Fishing from a PVC boat is radically different from coastal fishing, requiring the fisherman to have greater mobility and a specific approach to equipment. The fishing rod It is a key tool in the boating's arsenal, allowing efficient capture of coastal dumps, snags and grass thickets without the noise of oars or motors. Unlike classic spinning, this projectile has a shortened rod and is often equipped with a multiplier or non-inertial coil, which provides maximum control over the bait.
The choice of the right gear directly affects the effectiveness of fishing, especially when catching a predator in the wiring or plumb. Short rod It allows you to react instantly to a bite and safely fish without the risk of entanglement of the fishing line on the side or the engine, and the correct organization of the fishing area using the onboard fishing rod frees up your hands and space in the cockpit, which is critical for safety on the water.
In this article, we will explore all the nuances of choice, from the materials of the form to the methods of secure attachment of the gear to the inflatable board. You will learn why standard spinning rods often lose to specialized models and how to equip the workplace yourself. A competent approach to equipment will turn your boat into a full floating platform for trophy fishing.
Design features and types of onboard rods
Modern fishing-rod The main difference from traditional fishing rods is the length of the form, which usually varies from 1.2 to 2.1 meters, and this compactness allows you to work comfortably in a limited cockpit space without touching the motor, fun keys or a boatmate.
The materials of manufacture play a crucial role in the specifications of the gear. carbon Carbon sheets instantly transmit even the most careful touch of fish to the bait, which is impossible to feel with heavy fiberglass analogues.
⚠️ Note: When using carbon rods in a PVC boat, be sure to watch for sharp edges of fittings and hooks - one wrong stroke can damage the boat cylinder or break the form itself.
By type of construction, the onboard fishing rods are divided into several categories, each of which is designed for certain fishing conditions. Fast is ideal for jig wiring and working with heavy loads on the current, while slow is better for catching light splashes or wobblers, where cushioning of fish jerks is important.
- 🎣 rods for sheer flaming - ultrashort models with a rigid set for vertical wiring.
- 🎣 Spinnings for catching in the throw - are up to 2.1 meters long and allow accurate throws along the side.
- 🎣 Universal models - medium option, suitable for both wiring and for neat throwing.
An important element of the design is the bandwidth of the rings. On the side fishing rods, the rings often have an increased diameter and a reinforced design to withstand the loads when catching large fish from close range. Particular attention should be paid to the quality of the insert in the last ring (tulip), as it experiences the maximum friction of the fishing line when cut.
Fish rod attachment systems to PVC boat
Without a reliable mount, you can't use a fishing rod, especially when fishing in windy weather or on the current. The fisherman needs to have free hands to control the boat, sonar or preparation of gear while the rod is waiting for the rod to bite. There are several basic ways to fix the tackle on the inflatable side, each of which has its advantages and disadvantages.
The most common option is inflatableThese are sealed chambers with a pocket for a rod, which are attached to the side of the boat with Velcro or special belts and do not require drilling or gluing additional elements, the main advantage of such holders is their mobility and no risk of damage to the cylinder with rigid attachments.
A more permanent solution is the installation PVC-pipe holders This method requires precision and the use of a special glue for PVC fabrics, but provides the rigid fixation necessary to fight a large predator, fixed holders do not shift during sharp jerks and are always in a pre-selected convenient place.
☑️ Checking the fishing rod attachment
| Type of attachment | Difficulty of installation | Reliability | Mobility |
|---|---|---|---|
| Inflatable pocket | Low. | Medium | High. |
| Sticking the pipe | High. | High. | Low. |
| Strubbine on the jar | Low. | Medium | Medium |
| Railing system | Medium | High. | High. |
For those who do not want to mess with glue, a great option are holders attached to the banks (seats) These are fixed by screw clips or belts and allow the rod to be positioned according to wind or current direction, but it should be borne in mind that mounting on a jar may limit leg space or the placement of a gearbox.
Selection of coil and fishing line for onboard fishing
The in-flight fishing rod must be fitted with a special approach, as the conditions of operation on the water are very different from coastal fishing. First of all, the coil must have high corrosion resistance, constant contact with splashes of salt or fresh water, as well as high humidity dictate their requirements for the materials of the shell and mechanism.
The optimal choice is considered to be non-inertional coils sized from 2000 to 4000 according to the Shimano classification. multicoilMultipliers are also more convenient for vertical bait play, as the thumb always controls the cord's descent.
⚠️ Warning: After each fishing, be sure to wipe the coil with a dry cloth and periodically lubricate the mechanism, even if it is labeled "Waterproof" - the warranty does not protect against salt corrosion.
The choice of fishing line or wicker cord depends on the transparency of the water and the type of prey expected. The wicker cord (plait) is practically not stretched, which gives maximum information when fishing at depth. Monophile fishing line, having extensibility, can serve as a shock absorber for catching sharp fish, but at depths greater than 5-7 meters, its use becomes inefficient due to sailing.
- 🧵 A wicker cord - for jig fishing and great depths, where sensitivity is important.
- 🧵 Monolesque - for catching glitters and wobblers, where a natural game of bait is required.
- 🧵 fluorocarbon - as a leash material for protection from pike teeth.
How do you extend the life of a coil?
After the active season, it is recommended to completely disassemble the coil, remove the old lubricant and apply a new one, specialized for fishing gear, which is especially true if you have been fishing in salt water.
The timbering and winding quality are important. On the side fishing rod, the coil is often in a position close to horizontal or inverted, so the mechanism must hold the turns reliably. Friction brake It should be set up in advance, since it can be difficult to quickly regulate it with wet hands in the midst of catching a trophy.
Fishing and wiring from the board
Boat fishing offers the fishermen the opportunity to use techniques that are not available on shore. wiredWhen the boat is slowly drifting over a promising area, and the angler is catching different horizons of water, the onboard fishing rod allows you to keep the bait in the bite zone much longer than when throwing from shore.
When you're fishing in a plumb (vertical flare), the range of rod motion is minimal. The fisherman sets rhythmic brush sways, causing the bait to "dance" in place. Here, the rigidity of the hand-bait bond provided by the short rod is critical. Any resistance or bump is immediately transferred to the hand, allowing instant cutting.
For successful wiring, the direction of wind and current must be considered, and the boat should be placed so that it drifts with its nose or stern to the wind, but not with the side, otherwise the control of the gear will become impossible. Anchor falla It must be configured to allow it to move slowly in the wind without getting stuck in one place.
Use the sonar while wiring to see the fish's reaction to your game. Adjust the amplitude of the rod's flaps depending on whether the predator is climbing for the bait or staying at the bottom.
Fan tactics are often used, where anglers anchor and catch a sector around the boat, changing the angle of throwing or lowering the bait, and the onboard fishing rod allows you to do this quickly and silently without getting up, especially when catching a cautious perch or perch, which can be frightened by the noise of movement in the boat.
Safety and preservation of tackles on the water
Boat Fishing is not only a pleasure, but also an increased risk of losing expensive equipment. Falling a fishing rod overboard is one of the most common troubles that occur due to a sharp jerk of fish or a gust of wind. To avoid losing gear, experienced water-engines use special special equipment. safety-cord (links) which are attached at one end to the rod combo and at the other to the element of the boat or the fisherman's vest.
In addition, you need to monitor the position of sharp hooks and tees. In the tight space of the PVC boat, there is a high risk of hooking on clothes, a life jacket or, worst of all, the fabric of the cylinder. Puncture of the inflated side at a depth can lead to a serious accident, so all manipulations with the tooling should be carried out as carefully as possible.
⚠️ Warning: Never leave the fishing rod unattended, even if it is secured in the holder. Large fish can drag the tackle along with the holder if it is not reliable enough, or confuse the fishing line around the propeller of the motor.
Storage of gear during transportation also requires attention: rods should be disassembled and placed in tubes or covers, protecting them from mechanical damage and ultraviolet radiation. Prolonged exposure to direct sunlight on thin carbon can lead to degradation of the binder material and loss of strength of the form.
- 🛡️ Use it. retro (See) the safety cord so that it does not interfere with the catching.
- 🛡️ Always have an extractor or clamp on hand for quick extraction of the hook from the fish's mouth.
- 🛡️ Check the condition of the fasteners before each release to the water.
The safety of the boat and the fisherman is always more important than the fish caught – use insurance for rods and watch out for sharp hooks.
Maintenance and care of onboard gear
Aggressive aqueous environments, temperature changes and mechanical stress quickly disable gear if not given proper attention. Regular maintenance of the onboard fishing rod will prolong its life and maintain its performance. The main enemy of metal elements is corrosion, and for graphite - microcracks from impacts.
After each fishing, especially in salt water, the rod and coil should be wiped with a soft wet cloth, removing salt, sand and silt. Particular attention should be paid to the joints of the knees and the handle, where dirt can accumulate. It is recommended to treat the graphite form with special polishes that create a protective layer and mask small scratches.
The coil should be periodically disassembled and lubricated, according to the manufacturer's instructions. If you notice a backlash in the spoole or a jamming mechanism, do not postpone repairs - on water, a break in the coil can mean a loss of trophy and good mood. Timely replacement of bearings And the gears will cost less than buying a new coil.
Keep the gear in a dry, cool place, in a vertical position or in a disassembled form in a case. It is not recommended to leave the collected fishing rod with a stretched fishing line for a long time, as this can lead to deformation of the form and loss of its elasticity. Proper storage ensures that next season your fishing-rod He will be ready for any tests.
How to properly store the rod in winter?
In winter, the rod should be stored at room temperature, away from the heater. Before long storage, loosen the friction of the coil so that the springs do not lose their elasticity, and treat the form with a protective composition.
Can I use a sea fishing rod in fresh water?
Designed for saltwater, rods have enhanced corrosion protection and will last even longer in fresh water, and the key is to keep them washed after fishing.
What is the optimal length for a boat 3 meters long?
For a boat with a length of 3 meters, the optimal length is considered to be a rod length of 1.5-1.8 meters. This will allow you to work comfortably with both hands without touching the sides and the engine, and at the same time give you enough leverage for cutting.