Effective fishing with a swimming means is impossible without competent distribution of space and proper placement of gear. Spinning holder It's one of the key pieces of equipment that frees the fisherman's hands, allowing him to control the boat, change baits or cook. In a limited area of an inflatable vessel, every centimeter counts, so installing this accessory requires a thoughtful approach.
Incorrectly selected or installed fixator can not only spoil the pleasure of fishing, but also damage the board. PVCThe current market offers many solutions, from simple plastic glasses to complex pivot mechanisms with angle-of-attack adjustment, and understanding the design features of each type will help you avoid unnecessary costs and errors when tuning.
In this article, we'll go through all the nuances of the choice, look at the ways of attachment and provide step-by-step instructions for installation. You'll learn how to turn your inflatable boat into a full-fledged fishing boat, equipped with convenient points for rods. Safety and functionality are two whales on which a competent body of water is built. tuning.
Criteria for choosing a reliable rod fixator
Before buying, you need to clearly define the operating conditions and type of gear used. There are no universal solutions, since light spinning for ultralight and heavy trolling rod require fundamentally different approaches to fixation.
Plastic models are popular due to their low price and lack of corrosion, but they can be brittle at low temperatures or severe impacts on the side. Metal products, especially stainless steel or anodic-coated aluminum, are highly durable, but require careful handling so as not to damage. PVC tubesIt's important that all the faces are rounded and no sharp edges are present.
⚠️ Note: The use of holders with sharp metal elements without protective linings is strictly prohibited, as one awkward movement can lead to a puncture of the balloon and an emergency situation on the water.
You should also pay attention to the diameter of the boarding glass. The standard size is 35-40 mm, but some specialized rods can have a comet of a different diameter. The presence of a drainage hole at the bottom of the glass is an important nuance to prevent water accumulation, which, when frozen or just rolled, can create extra stress.
Types of structures and methods of fastening
There are several main types of holders, each with its own advantages and disadvantages, and the choice of the specific type depends on the design of your boat and your personal fishing preferences.
- 🎣 Tranza models - fasten directly to the wooden transom, providing a rigid fixation, ideal for trolling or fishing in plumb.
- 🎣 Inflatable holders - glued or screwed to the soft elements of the boat, often have a flexible basis for compensation of pitching.
- 🎣 Rail anchorages - are installed on an aluminum profile (slat), if it is provided by the design of the vessel, allowing you to move gear along the side.
Transse variants are considered the most reliable for active fishing, because they take the load on the rigid structure, bypassing the soft sides. However, their installation requires the drilling of the transom, which is not always desirable. Inflatable modifications are easier to install, but require the use of special platforms or reinforced inserts into the fabric. PVC for load distribution.
Special attention should be paid to the rotary mechanisms that allow you to change the angle of rod inclination, which is especially useful when catching large fish or when you need to quickly free up space, such devices are more difficult to maintain, but significantly increase the comfort of fishing.
Preparation for installation: tools and materials
You can't have a good installation without a good tool, and you can't have a rush, because a mistake can cost you the integrity of the boat, and you can have everything you need in advance to make sure that it goes smoothly and safely.
To work you will need: a drill with a set of drills (including drills for metal and wood), a sealant for PVC materialsIf you plan to glue the platform, you will also need a degreaser and a special glue that is compatible with the material of the boat.
☑️ Checking readiness for installation
It is important to choose the right place to install, it should be easily accessible, but not interfere with the movement of the boat. Make sure that in the selected area there are no hidden structural elements that can be damaged by drilling. Careful marking - the key to successful installation.
Step-by-step instructions for installation on a transom
Mounting on a transom is the most common way to ensure maximum rigidity, a process that requires precision, but is quite feasible at home. Follow the step-by-step instructions for the best results.
- Try on the holder to the transom and choose the optimal place of installation, taking into account the angle of inclination of the rod.
- Drill holes in the transom, pre-protecting the area around the drilling with paint tape from scratches.
- Treat the edges of the holes with a sealant to prevent moisture from entering the wood of the transom.
- Install fasteners and tighten them with moderate effort so as not to crush wood or plastic.
When drilling, use a slightly smaller diameter drill for the guide hole, and then expand it to the desired size. This will help avoid chipping and cracks. After installing the fastener, be sure to check the reliability of the fixation with a jerk of moderate strength.
⚠️ Note: When tightening bolts do not use excessive force - the pull can warp the transom or break the thread, especially if plastic or soft alloys are used.
Once completed, it is recommended that the sealant be allowed to dry for the time specified by the manufacturer before getting on the water, and only after complete polymerization of the composition can the installation be considered complete and safe.
Nuances of work with composite transverses
If your boat’s transom is made of composite materials or has a honeycomb structure, standard drilling may not be sufficient, and in such cases it is recommended to use an epoxy resin to strengthen the hole walls before mounting the bolts to prevent material from stratifying under load.
Features of fastening on soft elements of the boat
Installation of holders on boards or special pockets requires special approach, since the load is distributed over a soft surface. Direct screwing to the cylinder is impossible and dangerous, so special platforms or stickers are used.
The most reliable option is to use ready-made platforms made of plywood or plastic, which are glued to the cylinder in a factory way or independently, and you can already mount standard glasses on such sites, self-pasting requires careful surface preparation and the use of high-quality glue.
| Type of attachment | Complexity | Reliability | Risk for PVC |
|---|---|---|---|
| Trants. | Low. | High. | Minimum |
| On the platform (glue) | Medium | Medium | Low. |
| Inflatable pocket | Low. | Low. | Missing. |
| Rail rail. | High. | High. | Medium. |
If you use inflatable pockets, make sure they are securely fixed and do not shift when rolling. To reinforce the structure, you can use additional belts or slings that run under the bottom of the boat, although this is less aesthetic, the main thing is to ensure the stability of the rod position.
To reduce friction of the line on the side when installing the holder on the soft side, use protective silicone linings or pieces of Cambrick at the contact point of the tackle with PVC.
Accessories security and maintenance
Regular maintenance of fishing equipment extends its life and ensures safety on the water, after each fishing, especially in salt water, you need to wash the metal parts with fresh water, which will prevent corrosion and jamming of moving parts.
Check the condition of the fasteners before each exit. Vibration and constant load can weaken the nuts and bolts. growers (spring washers) or using a thread fixer will help keep the connection reliable for a long time.
Check the place of attachment for fabric scuffs PVCEven a small scratch can develop into a serious problem under water pressure, and if defects are detected, repair or replace the mounting element immediately.
Regular prevention and inspection of the holders’ attachment sites is a mandatory procedure that prevents the loss of tackles and damage to the boat during operation.
Do not leave the tackle in the holders unattended for long periods, especially in windy weather. A gust of wind can rip out a rod or, worse, turn over a light boat if the tackle's sailing is too large. Prudence and foresight are the angler's best friends.
Frequently Asked Questions (FAQ)
Can you stick the holder directly to the balloon without a platform?
No, it's strongly discouraged. The glue will not withstand the point load and the fish jerks, which will cause the holder to tear off along with a piece of cylinder fabric. Always use a rigid platform base.
What diameter of the glass to choose for spinning?
The standard diameter is 35-40 mm. If you use specific rods with a very thin or thick set, it is better to take an adjustable glass or model with a rubber liner.
Do I need to lubricate the bolt thread during installation?
Yes, the use of graphite lubricant or carving fixer will prevent corrosion and spontaneous unwinding of the fastener from vibration, which is especially important for outboard motors and attachments.
Will the plastic holder withstand the large fish?
High-quality engineering plastic (such as ABS) is able to withstand significant loads, but for trophy fishing and hard trolling, it is preferable to use reinforced stainless steel metal models.