Homemade spinning holder for PVC boat on lyctros

Equipping an inflatable floating craft is a process that often turns into fascinating engineering creativity, especially when it comes to fixing tackles. Holder of spinning for PVC boat himself on lyctros It's one of the most practical solutions to free the fisherman's hands and keep expensive rods from falling overboard, and unlike rigid attachment to the board, the lyctross system offers flexibility, allowing you to reconfigure the cockpit depending on the type of fishing you're fishing for.

Many anglers mistakenly believe that a complex metal welded structure or expensive factory accessories are necessary to reliably fix the fishing rod. lyctros The key here is understanding the tension mechanics of the cable and the proper load distribution.

In this article, we will take a look at the steps to build such a device, from the choice of materials to the final installation, what tools you will need, how to avoid typical installation errors, and why this system is considered the gold standard for inflatable boat owners. The main advantage of the system on lyctross is the absence of the need to drill cylinders or glue additional sites.

Design features and advantages of the system on lyctros

Before starting the manufacture, you need to clearly understand what is lyctros And why it's so popular with water engines, and the lyctross is a cable that's put in pockets along the boat's beam, and it's the cable that's attached to the various accessories, like tables, anchors, and of course rod holders, and the main advantage is that the mounting is done without breaking the tightness or integrity of the PVC material.

A homemade holder designed for this system usually consists of a vertical rack and a horizontal platform with a tube under the combo or spinning handle. flyboat It's a dynamic platform that's constantly in motion, even in a parking lot because of the water turbulence, so it has to have a certain inertia and not be too light, or it's going to fall down all the time.

The use of lyctross allows the holder to move anywhere on the side, especially when fishing in overgrown bodies of water where you need to change position often, or when trolling, when the fishing rods need to be spread as widely as possible, and when transported, such a holder is easily dismantled and takes up a minimum of space in the backpack bag, which is a critical factor for owners of compact boats.

It's worth noting that the right weight distribution of gear on the lyctros reduces the sailing of the structure. multicoilThe center of gravity shifts, and the holder has to compensate for this advantage. In factory models, this is solved by thickened walls, but in homemade versions, you can use more massive base materials, which will only increase the stability of the entire system.

Required materials and tools for manufacturing

To create a quality and durable holder, you do not need to buy from specialized aircraft modeling stores or fishing products. Most materials can be found in a construction hypermarket or even in your own garage. The holder base must be made of a material that is resistant to corrosion and ultraviolet. stainless steelDuraluminum or quality plastic (e.g., PVC pipes for external sewerage or polypropylene).

The key to lyctross attachment is a special clamp or hook. It can be made from a steel strip 3-4 mm thick or use ready-made components from old bicycle trunks or furniture fittings. It is important that the metal is treated with anti-corrosion compound, since salt water and fish mucus quickly destroy unprotected surfaces. fastener: stainless steel bolts, nuts with grovers or threaded studs.

The list of tools you will need in the process is pretty standard, but their availability is necessary to get a neat result:

• 🛠️ Corner grinding machine (Bulgar) with metal and wood discs for cutting materials.
• 🔩 drill or screwdriver with a set of drills on metal and wood (diameters are selected for your fastener).
• 📏 Marking tool: roulette, coal mine, metal marker and core.
• 🔨 Fillers and fillers for removing burrs and finishing edges.
• 🧪 Chemistry: degreaser, epoxy glue (if a composite is used) and metal paint.

⚠️ Attention: When working with PVC pipes or plastic, avoid overheating the material when drilling, otherwise the edges of the hole will melt and become brittle. Use sharp drills and medium rpm.

If you plan to use wooden elements (which is acceptable for temporary or budgetary decisions), choose moisture-resistant rocks such as larch or oak, and be sure to cover them with yacht lacquer in several layers. However, for permanent use on water, wood is not the best choice due to the risk of rotting and swelling, which can disrupt the geometry of the holder.

Step-by-step instruction: creating a drawing and revealing details

Any quality homemade product starts with a sketch. Don't rely on an eyewatch, especially if you're making paired holders for the left and right sides of the boat. On a piece of paper or in a simple CAD program, draw a profile of the holder. You need to determine the height of the rack (usually 25-35 cm from the mounting level), the angle of the tube under the rod and the distance to the mounting axis on the lyctros.

The optimal height of the holder is selected individually, but the standard size is considered to be the size at which the handle of the spinning is just above the level of the seat (banks) of the boat. This allows you to quickly intercept the fishing rod and minimizes the risk of hooking hooks overboard when you are out. steel-strip It is 30-40 mm wide and the sidewalls are cut out, which are then connected by lintels.

When opening tubular elements (if you use tubes with a diameter of 20-25 mm for a glass under a comet), it is important to observe accuracy. The hole must be deep enough to hold the handle, but not so deep that the comet rests on the bottom and interferes with the installation. Often, a cork of dense rubber is pasted or inserted into the bottom of the glass, which serves as a shock absorber and prevents the handle from hitting the metal.

Pay special attention to the lyctross attachment node. This can be an U-shaped brace covering the cable, or a hook with a spring-loaded hold. If you make a brace, its inner width must correspond to the diameter of your lyctross with a small gap (1-2 mm), so that the holder does not hang around, but does not squeeze the cable. Too strong compression of the lyctros can damage its braid, which will lead to the loss of the tightness of the balloon in the place of the shaft.

Assembly technology and anticorrosion treatment

Holder assembly is the stage where disparate parts are transformed into functional products. If you use welding, be sure to clean the seams until smooth. Sharp edges or metal infusions can damage not only your hands, but also equipment, and even the boat itself, if handled sloppy. For bolt joints, use larger diameter washers to spread the load over the contact area.

Anti-corrosion treatment is not just a cosmetic procedure, it's a necessity. stainless steel In an aggressive marine environment or frequent contact with fish mucus, spot corrosion may occur. Ideally, powder paint is ideal, but at home, you can use metal soil (e.g., GF-021) and enamel in aerosol cans. Apply a coating in 2-3 thin layers, allowing each to dry according to the instructions.

For a tube that is inserted in the spinning, the inner surface can be pasted with a soft material, such as foamed polyethylene or a piece of car camera. shock-absorbing It will prevent scratches on the handle of your favorite spinning, and it will also reduce vibration and rattle of the gear while the boat is moving.

Secrets of durability of fasteners

Use a thread fixator (anaerobic sealant) on all bolt joints. Engine vibration and waves quickly unwind the normal nuts, which can lead to the loss of the holder along with the tackle.

If the holder design involves removable elements, make sure that they do not get lost. You can use chains or carbines. All moving parts, if any (for example, a swivel mechanism), should be lubricated with silicone lubrication that does not destroy the rubber seals and is not washed away with water.

Installation of the holder on the PVC boat

Installation of the finished product on the boat is the most important moment. Before inserting the holder into the lyctross, carefully examine the cable itself. It should not be scuffed, sticking out threads or dirt. If the lyctros is dirty, wipe it with a wet cloth. The insertion of the holder should be made smoothly, without jerking, so as not to damage the internal structure of the timber.

Once installed, check the stability of the fixation. The holder should not be loosely hanging from side to side. If there is a backlash, it can be eliminated by placing small pieces of rubber or plastic between the clip and the lyctross. However, it is better to immediately make a clip with the exact dimensions. Make sure that when fully loaded with the tackle (spinning + coil), the structure does not heel excessively and does not pose a threat of tipping.

The position of the holders on the boat depends on your preferences and the type of fishing. For spinning, it is optimal to place behind the angler's back or along the sides in the cockpit area. It is important that the spinning handle is in the fast access zone in the ready position, and the splash or vertebrae does not touch the surface of the water if the boat is anchored.

Parameter	Optimal value	Permissible range	Note
Stand height	30cm	25-40 cm	Depends on the height of the fisherman.
Diameter of the glass	32-35 mm	30-40 mm	Under the arm of spinning
Basic material	Nerzh.	Aluminum, Plastic	Steel is more reliable
Weight of holder	0.5-0.8 kg	0.3-1.0 kg	Balance of stability and weight

⚠️ Attention: Never attach the holder to the inflatable part of the balloon directly with glue or Velcro without a rigid base. This can cause the cylinder to deform under load and rupture, only lyctros or rigid elements (banks, transom).

Operation, care and modernization

After each fishing, the holder must be removed from the boat, even if it is made of stainlessRinse it with fresh water to wash away the salt, sand and organics. Pay special attention to the ligtross attachment node, the grains of sand that get into the clamp mechanism work like an abrasive and can rub the cable. Periodically lubricate the moving parts with silicone.

Over time, you may notice that the standard design needs to be reworked, for example, you can add a removable pocket for trifles (flat-slingers, spare hooks) directly to the holder's rack. Some anglers put an LED flashlight on top of the rack, which is convenient for night fishing. Modernization is a natural process of improving their gear for specific tasks.

If you plan to catch at high speeds (for example, when moving to a catching point with decomposed tackles), holders are better dismantled. They create sailing and can cause accidents when abruptly maneuvering. Store homemade holders in a dry place, wrapped in fabric to avoid mechanical damage during transportation in the trunk of the car.

Frequently Asked Questions (FAQ)

Can I use a lyctross holder with heavy marine spinnings?

Yes, you can, but you need to strengthen the design. For heavy rods (test above 100-150 grams), it is recommended to make a holder with two points of support on the lyctross or use a wider and thicker steel strip (4-5 mm). It is also important to check the condition of the lyctross itself - it should be stretched evenly and not be damaged.

Will the metal holder damage the boat's cylinder when rolling?

The risk is minimal if the holder is fixed correctly and does not have sharp protrusions directed into the boat. The metal should not touch the inflatable part of the balloon. If the holder is mounted on the lyctros, it is in a timber that is structurally protected. However, when there is a heavy chop, it is recommended to monitor the position of the gear.

What diameter of the pipe is best used for a glass under spinning?

The standard spinning handle has a diameter of about 28-32 mm. The pipe should be taken with an internal diameter of 34-36 mm, so that the handle enters freely, but does not dangle. If the pipe is wider, you can use sealing rings made of rubber or neoprene, which will also extinguish the vibration.

Creating a PVC spinning holder yourself on lyctross is a challenge that is available to any angler with a minimum set of tools. The result of your work will be not only a functional accessory, but also confidence in the reliability of your equipment. Experiment with shapes and materials, and your fishing will become even more comfortable and productive.