Effective fishing with a swimming means requires not only high-quality gear, but also competent equipment of the vessel itself. Holder of spinning in PVC boat The lack of regular rod seats on most inflatable models forces owners to solve the problem of fixing them during crossings or catching trophies.
Incorrectly selected or mounted accessory can lead to damage to cylinders or loss of expensive equipment. In this article, we will discuss in detail the types of fasteners, how to install them and the nuances of operation that will help you make the right choice.
Criteria for selecting inflatable anchorages
The market of accessories for water-motor subjects offers a wide range of solutions, but not all of them are suitable for the use of water-motor equipment. squirrel-stuffThe main requirement is the absence of sharp edges and rigid elements that can damage the PVC fabric under load or friction. The product material must be resistant to the aggressive effects of salt water, ultraviolet light and mechanical shocks.
When choosing a model, you should pay attention to the type of fixation. For the side, soft attachments on Velcro or belts are most often used, which evenly distribute the load. Metal structures are permissible only if there is a wide rubber or plastic gasket at the point of contact with the balloon.
- 🎣 Material: Preferably, ABS plastic, AISI 316 stainless steel or anodized aluminum.
- 🛡️ Defense: presence of soft linings or a wide base to prevent the tissue from being pressed.
- 🔄 Universality: the ability to adjust the angle of inclination and compatibility with different diameters of handles.
It is important to bear in mind that spinner It must withstand the snatch load when cutting, if you plan to use it in active fishing. Cheap Chinese counterparts often break at the most inopportune time, so saving on this element of tooling is rarely justified.
Types of holders: transom and onboard models
Structurally, all devices for fixing rods are divided into two main groups: installed on a transom and attached to the board. Trans holders These are rigid structures that are mounted on a vertical plane of the feed, and they're ideal for trolling or plumbing, where you need to hold the gear tightly.
The onboard variants are more versatile and are often used by spinning practitioners who practice throwing, they can be removable or stationary, and the combined models that allow you to fasten the fishing rod both vertically and at an angle deserve special attention.
The choice between these options depends on your fishing style. If you change fishing locations often and need to quickly remove gear, removable onboard models will be more convenient. For static fishing at great depths, stationary transom solutions are preferable.
Instructions for mounting the holder on the cylinder
Installation of the mounting on an inflated boat requires caution and adherence to technology. Before starting work, make sure that the balloon is clean and dry. Fat or dirt can reduce the effectiveness of adhesive joint or belt fixation.
The process of installing a soft holder usually takes no more than 10-15 minutes, and it is important to position the element correctly so that it does not interfere with the rowing and does not block access to valves or anchor ditch.
☑️ Preparation for installation
⚠️ Attention: Never use adhesives based on aggressive solvents (e.g. acetone) directly on PVC fabric without first testing in a discreet area, as this can disrupt the structure of the polymer layer.
When using Velcro belts, try not to over-tighten them so as not to deform the balloon at the point of contact. Optimal tension should ensure that the attachment is fixed with a moderate jerk.
Installation on the transom: features and nuances
Installation on a transom involves working with a harder surface, but there are risks. The main problem is vibration transmitted from the motor, which can loosen the mounts, so the use of fixing nuts with growers or a threaded fixator is mandatory.
If the transom of your PVC boat is made of plywood coated with moisture-resistant paint, make sure that drilling holes does not violate waterproofing. In such cases, it is better to use overhead brackets that do not require violation of the integrity of the bulkhead.
| Type of installation | Essential tools | Time of installation | Complexity |
|---|---|---|---|
| On the belts (board) | No. | 2 minutes | Low. |
| Glue (board) | Brush, degreaser | 30 min + drying | Medium |
| Drilling (trans) | Drill, keys, sealant | 20 minutes | High. |
| Invoice (transom note) | Screwdriver, keys. | 10 minutes | Low. |
For metal transes that are found on premium boats or hybrid models, standard marine brackets are suitable. However, here too, you need to remember about the galvanic pair: aluminum and stainless steel in salt water can corrode without insulating gasket.
Protecting PVC tissue from damage
The main enemy of an inflatable boat is point pressure and friction. fishing-rod The cloth may be wiped over time if it is constantly shifted relative to the surface of the cylinder, and additional protective elements are recommended to minimize risks.
A great solution is to line a piece of thick rubber, linoleum or special reinforced tape under the base of the mount, which will increase the contact area and reduce pressure on a square centimeter of the surface.
How to check the wear of the fabric under the holder?
Every time you service the boat, take off your attachments and look carefully at the fabric, look for scuffs, color changes, or small villi, and if the fabric is thinner or has changed structure, it's a signal to replace the protective lining or change the attachment location.
Check the condition of your belts and Velcro straps regularly. A weak attachment will start to "ride" on the cylinder while the boat is moving, working as an abrasive. Timely lifting or replacing worn-out belt elements will prolong the life of your vessel.
Operation and care of accessories
After each fishing, especially in salt water, the fasteners must be rinsed with fresh water, and the salt crystallizes and can damage the movable angle adjustment mechanisms or damage the coating of metal parts.
Keeping the boat with the hard elements removed, if possible, will reduce the load on the cylinders during deflation and folding, and will also prevent accidental punctures during packaging.
- 🧼 Cleanup: Use a soft sponge and neutral detergents.
- ☀️ Drying: Before packaging, make sure that all the elements are completely dry.
- 🔧 Check: Check the swelling of the bolt joints once a year.
⚠️ Attention: Do not leave a boat with rigid holders installed in direct sunlight for a long time unattended. Heating metal or dark plastic can cause local overheating and deformation of PVC tissue at the point of contact.
Homemade solutions and tuning
Many anglers prefer to make their own holders using PVC pipes, residues of reinforced fabric and fittings, which allows you to create a device that is ideal for the specific model of the boat and the style of fishing of the owner.
The foundations are often made with sewer pipes with a diameter of 50-110 mm, which are strong and chemically resistant, and the attachment to the board is realized through welded or glued ears made of the same fabric as the boat itself.
Use the residues of fabric from the repair of the boat to make soft bases for homemade holders, this will ensure the perfect match of color, texture and expansion coefficient of materials at temperature changes.
When self-manufactured, it is important to balance the rigidity of the structure with the safety of the cylinder. Unnecessarily rigid homemade can cause a water accident, so always test new solutions on the shore.
The homemade holder should be lighter than the factory analogue, but have a large support area to reduce the specific pressure on the cylinder.
Frequently Asked Questions (FAQ)
Can I use a car holder for a phone in a boat?
Technically, you can adapt the mount, but it's a bad idea. Car mounts aren't designed to be in constant contact with water and salt, their mechanisms will quickly rust, and their suction cups don't hold well on the rough surface of PVC tubes.
What is the maximum spinning diameter of a standard holder?
Most universal models are designed for handles with a diameter of up to 35-40 mm. For powerful rods with thick lumps (for example, for sea fishing), you should look for specialized models with the marking "Big Game" or an increased diameter of the glass.
Will PVC glue damage the boat fabric during dismantling?
If you use a specialized polyurethane adhesive for PVC, then with careful removal (heating hair dryer and mechanical rolling), the damage is minimal. Aggressive adhesives can dissolve the top protective layer of tissue, leaving an inexorable trace.
Do I need to remove holders when transporting a boat in a trailer?
Hard transceiver holders are better removed so that they do not vibrate or loosen the mounts. Soft side mounts can be left, if they are securely fixed and will not rub against other objects when laying the boat in the case.
Is there a difference between a casting holder and a spinning holder?
Yes, there is. Casting rods have a coil on top and spinning rods on the bottom, and the cups of holders can have different cutout shapes or adjustments to make up for this difference and ensure that the gear is vertically positioned.