When choosing a boat for fishing or family vacation on the water, potential owners often face the need to accurately calculate the space. The length of the boat Kazanka 5M2 It is one of the key parameters that determine not only capacity, but also transportation on the roof of a car or in a trailer, a model that has become legendary for its reliability and seaworthiness, requires careful planning of storage.
Understanding the actual dimensions of the housing helps to avoid unpleasant surprises when you go down to the water or park in the garage. aluminum-magnesium alloysThe hulls are made of hulls that don't allow the boat to be folded into a backpack, so every centimeter counts. boat-engine.
In this article, we will discuss in detail all the nuances of the hull geometry, the effect of trans on the total length and practical aspects of operation. You will learn how to measure the vessel correctly and why data-sheet figures may differ from the actual measurements on older copies. small-boat.
data-sheet figures and actual dimensions of the hull
Official documentation accompanying Kazanka 5M2 According to the technical data sheet, the length of the hull on the waterline and the maximum length is 5000 millimeters, however, when buying a used boat or ordering transportation services, it is important to take into account possible deviations associated with years of operation and repairs.
Metal tends to deform when hitting solid objects or when installed incorrectly on a trailer. bottom-up Or we could use a piece of tape to digest the seams, and the geometry could change by a few centimeters in one direction or another, and for the precise measurement of the dimensions, it's always better to use a tape measure, applying it from the most protruding point of the nose to the edge of the transom.
The width of the midline body also plays an important role in the overall picture of dimensions, being 1600 mm. In combination with a length of 5 meters, this gives excellent stability, but creates sailing in the wind. When calculating space in the garage or in the parking lot, you need to take into account the maximum protruding points, and not only the theoretical figures from the manual.
⚠️ Warning: When measuring an old boat, be sure to check the condition of the forehead. If the bow was crumpled on impact and then straightened, the real length may be 2-3 cm less than the passport, which affects the centering.
For owners planning to install additional equipment, The actual length of Kazanka 5M2 with an anchor box or reinforced forespeak installed can reach 5100-5150 mm. This is critical for picking a case or calculating a place in a narrow garage box.
Effect of transom design on total length
One of the main features of the model 5M2 The design of the transmutor (stern bulkhead) directly affects how the boat will behave on the go and what its final length is with the engine installed. The standard transmuter is designed for motors up to 30 hp, but enthusiasts often strengthen it for more powerful units.
Installation boat-engine The overall length of the composition increases significantly. The lower unit engine acts behind the stern, and this distance must be taken into account when descending from a flat shore or anchoring. Kazan 5M2 The departure of the engine in the transport position adds about 80-100 cm to the dimensions.
- 📏 The standard departure of the engine's 9.9 hp is about 85 cm from the plane of the transom.
- ⚓ When installing an electric motor on the tubel control, the length increases less than with a gasoline analogue.
- 🔧 The reinforcement of the transom with the linings can visually change the geometry of the feed, but does not affect the length along the waterline.
It is also important to consider the angle of inclination of the transom: if the angle has been changed during repair or tuning, this can affect the driving performance and the position of the daywoot relative to the water. Properly installing the motor ensures that the anti-cavitation plate is in the right position, without creating excessive resistance and without increasing the effective length of the submerged part.
When installing the motor on Kazanka 5M2, use transmutation boards made of moisture-resistant plywood with a thickness of at least 25 mm to avoid deformation of the mount and displacement of the engine back.
Table of the main overall specifications
For ease of comparison and planning, the basic dimensions below are helpful. Kazan 5M2 The figures may vary slightly depending on the year of manufacture and the specific modification (e.g., the presence of a bow awning or trunk).
| Parameter | Value (mm) | Value (m) | Note |
|---|---|---|---|
| Longest length | 5000 | 5.0 | By the side. |
| largest width | 1600 | 1.6 | Midel. |
| Height on midship | 700 | 0.7 | No patches. |
| Hull mass | 190 (kg) | - | No motor. |
| Load capacity | 400 (kg) | - | Including the crew. |
Analyzing the table, you can see that the ratio of length to width provides good speed, but requires accuracy in the side wind. the height of the side of 70 cm is comfortable for safe on board, but when fully loaded (400 kg), the waterline rises, and the buoyancy margin decreases. Load capacity It is distributed evenly, but the center of gravity shifts to the stern when installing a heavy motor.
Why is the weight of the boat different from the passport?
The weight of 190 kg is averaged. The actual weight depends on the thickness of the metal used in the repair, the number of paint layers applied, the presence of installed equipment (anchors, crates, seats) and the humidity inside the structure. Old boats can weigh up to 210-220 kg due to accumulated fat, dirt and corrosion.
Transportation: the roof of the car and the trailer
Issue of transport The Kazan 5M2 is particularly acute because of its five-meter length. Not every car is able to take on the roof a load of this length without special elongated arcs. Standard crossbars are often 110-120 cm long, which is not enough to reliably fix the 160-centimeter width of the boat.
When transporting on the roof, you need to take into account overhangs. The nose and stern will project far beyond the dimensions of the car. According to traffic rules, if the load protrudes by more than 1 meter, it must be marked with signal (flags or a flashing orange light at night), ignoring this rule can lead to a fine and create an emergency situation.
- 🚗 For transportation on a passenger car, elongated arcs or a specialized trunk from 2 meters long are required.
- 🚛 Using a trailer-boat trawl is a safer option for long journeys.
- 🔒 Mounting should be carried out at least four points: two at the nose and two at the transom, using dynamic belts.
The alternative to the roof is to use a trailer, in which case the length is the length. Kazan 5M2 A standard lounge trailer must have a platform length of at least 4.5-4.8 meters so that the bow of the boat does not hang in the air, which can lead to vibrations and damage to contours when driving on the highway.
⚠️ Warning: When transporting over long distances, be sure to check the tension of the belts every 50-70 km. Vibration and oncoming air flow can weaken the mounts, which will cause the body to shift.
☑️ Checking transport readiness
Features of storage and placement in the garage
Planning a purchase Kazan 5M2And so, you know, a lot of people forget about the size of the storage space. Five meters is a lot of space. If your garage is a standard 3x6 meter garage, the boat will occupy almost all the usable space, leaving little space for passage or storage.
The best storage option is to install the boat on keel blocks or special stands, which prevents deformation of the bottom under its own weight for a long period. The metal body must "breathe", so storage on the ground or in water all year round without preservation is unacceptable and will lead to accelerated corrosion.
If the garage is narrow, you might consider keeping the boat upside down, which takes up less space in width because the cheekbones don't interfere, but you need either special equipment (thalrep, winch) or the help of several people to turn the 190-pound hull over. Bottom-up storage It also protects the cockpit from dust and rodents that like to nest in soft seats.
It is important to provide ventilation in the storage area. Condensation formed on cold metal at temperature changes can lead to foci of rust. Regular ventilation and use of silica gel sacs or moisture absorbers will help to preserve the environment. aluminum-magnesium alloy All in one.
Storing a boat on keelblocks in a dry, ventilated room increases the life of the hull by 30-40% compared to storing it on the ground or in the open air.
Comparison with analogues and modifications
There are many modifications on the market. KazanThe 5M2 is often compared to the 5M, 5M4 and 5M7. The main difference between the 5M2 and its predecessor (5M) is the presence of factory transmuter cans and reinforced transmuter, but the length of the body is identical to 5 meters.
A new model Kazan 5M4 It has rounded contours and slightly altered nasal geometry, but it also fits into a 5-meter standard. Kazan 5M7 It's already 4.8 meters long, making it a little smaller, but less roomy, and understanding these nuances will help you find parts or blueprints for repairs.
Comparison with competitors, such as salute or Ob, shows that Kazanka 5M2 wins in width, but loses in length to some six-meter models. For fishing in large reservoirs, 5 meters is a middle ground, providing both speed and stability. Shorter boats (4 meters) can be dangerous on the wave, and longer ones are more difficult to transport.
When choosing between the used Kazanka 5M2 and more modern analogues, you should consider not only the length, but also the condition of the metal. An old boat with perfect geometry is better than a new one, but with a broken seam structure. Carefully examine the angles and connections to the deck - this is where cracks often occur in age-old specimens.
Can I extend the 5M2 Kazanka?
Theoretically, you can weld a welder in the middle of the case, but it will violate the design stability and strength. The factory design is designed for certain loads, and any change in length requires professional engineering recalculation, which is impossible to do at home.
Frequently Asked Questions (FAQ)
What is the real length of Kazan 5M2 with the engine installed?
With an average power engine installed (e.g. 9.9 hp), the total length of the composition is approximately 5.8 - 5.9 meters. This depends on the length of the daywut of the particular engine and its angle of inclination. For transport on the trailer, consider a margin of at least 6 meters.
Will the 5M2 fit into a standard garage?
A standard garage measures 3x6 meters. A boat 5 meters long will fit into the length, but will occupy almost the entire width (1.6 m), leaving narrow passages. If the garage is already (for example, 2.5x5.5), then you can only place the boat diagonally or upside down, which will make access difficult.
Does the length of the boat change after the seams are reinforced?
When properly repaired and reinforced seams, the length of the case does not change. However, if you replace the sheets of coating with overlapping or add large-thick hinged bars, the overall width and length can increase by 1-2 cm.
Do you need a special permit to transport a 5-meter boat on the roof?
Special permission is not necessary if the cargo does not protrude beyond the dimensions of the car by more than 1 meter behind and front. If Kazanka 5M2 is issued far beyond the roof, you need to mark the protruding ends with flags (day) or a lantern (night) according to traffic rules.
What is the maximum wavelength safe for Kazanka 5M2?
Kazanka 5M2 refers to the planing boats and confidently holds the wave height of 0.75 meters (three points). With a larger wave, there is a risk of overboarding or damage to the hull on the crest of the waves, especially when moving against the wave.