Boat Fishing opens up opportunities for fishermen that are not available to shoreliners. You can quickly change the point, catch distant eyebrows and scorched pits where it is physically impossible to throw from the shore. However, classic bottom fishing in these conditions requires a specific approach, and this is where the help comes from. feeder.
Unlike standard rods, this tool has a unique design that allows you to catch effectively even in limited space. The fishing rod It doesn't require long-range throws, because the boat is already above the stern table, and it changes the tactics and the requirements of the tackle.
If you are planning to buy an onboard feeder from a boat, it is important to understand the difference between a classic feeder. feeder specialized rodThe first can be used for anchor fishing on the current, the second is often short hard whips, and the right choice of equipment will be the key to successful fishing in the depths.
Features of the design of onboard rods
The main difference between a specialized fishing rod is its length and rigidity. The standard length of such models varies from 1.2 to 2.1 meters. This is due to the fact that there is no place to wave long spinning in the boat, especially if it has two or three people.
The second important aspect is the bandwidth rings, which are positioned on high legs in quality models, which prevents the wet line from sticking to the blank. tulip The top is often reinforced with tungsten carbide or ceramics, because the load on it when you pull it out from a depth of 5-8 meters is enormous. The line must slide freely without creating parasitic friction.
The material of the form is also key. For boat fishing, the ideal choice is to make a boating trip. carbon It's a very tiring, high-graphite composite, and these materials provide the necessary stiffness and, most importantly, the minimum weight, and it's tiring to hold a heavy rod in your hand for hours, constantly controlling the tension of the line, and it's a little bit of a tiring, and a little bit of a gear that allows you to focus on the bite, not on the fatigue of the arm.
Some models are equipped with removable tops-quivertypes, as well as classic feeders, which allows you to adapt the gear to different conditions of the flow and weight of the feeder used, but for onboard fishing, you often choose a monolithic whip with a built-in alarm or a separate nod.
When choosing a rod, pay attention to the material of the handle. The cork is more comfortable in cold weather and does not slide in a wet hand, unlike pure rubber or EVA.
Selection criteria: test, length and structure
Before you buy an onboard feeder from a boat, you need to clearly define the conditions in which you plan to fish. The main parameter is the rod test. It depends on the strength of the current and the depth at the fishing point. On moderate rivers, such as the Oka or the Volga in mid-latitudes, the optimal test will be in the range of 40-80 grams. For a strong jet, such as on the Kama or in the lower reaches of large rivers, you will need a more powerful form with a test up to 120-150 grams.
The length of the rod is selected individually, but the gold standard is the range of 1.5-1.8 meters. Shorter models (up to 1.2 m) are good for fishing with a pin (verbal) or with a nod, but they are more difficult to control the catching of large fish. Long models (about 2 m) allow you to make neat throws away from the boat, which is useful for catching cautious fish afraid of the shadow of the boat.
Building the form is also important. fast or mid-fastThis is necessary for instant cutting, as the depth is often greater than 5-6 meters, and the fishing line has considerable extensibility. A slow form will eat part of the jerk when cut, and the fish can get off the hook.
Installation of equipment and selection of coil
The reeling of the onboard feeder is a separate topic to discuss, because long-range casting is not required, powerful traction meat grinders are not needed here, small, non-inertial coils of 2000-3000 size according to Shimano classification are ideal, the main requirement is the reliability of the friction and quality laying of the fishing line.
Many experienced fishermen prefer to use the Inertial coils or even simple coils attached to the form, which simplifies the design, reduces weight and eliminates the risk of failure at the most inopportune moment. For fishing at depths up to 10 meters, an inertial coil with a 1:1 gear ratio (or just a drum) is an excellent choice.
As the main line, it is better to use a wicker cord with a diameter of 0.10-0.14 mm. The wicker does not stretch, which is critical for registering cautious bites at great depths. Monophile fishing line at depths of more than 5 meters turns the tackle into a "telegraph wire" that does not transmit the fish touching the bait.
The feeder can be anything from a paternoster, a Gardner loop, an inline or a helicopter, but it's often a simplified version of the feeder, which is attached to a separate leash or is part of the main gear, and it's important that the feeder is not confused with the feeder when it's caught.
☑️ Checking tackle readiness
Fishing techniques and feeding tactics
Fishing from the boat is very different from the onshore one, where you don't feed the dot in advance, but you create a stern directly under the boat, and you use dump truck feeders or rockets that fill up with bait and sink to the bottom, and after the devastation, the feeder pulls up, fills up again, and the process repeats.
The wiring technique is also specific: the angler can play with bait, slightly lifting and lowering the rod, which is impossible to do from the shore at a long distance. This "animation" often provokes bream, booster and sazan to attack, especially effective in moments of complete negligence.
It's important to anchor the boat properly. For feeder fishing, the boat is either cross-current (stretch) or stern against the current. The first option is more convenient for catching a wide strip of bottom, the second is for catching at a specific point. With strong wind and current, the boat can shift, dragging the tool, so the anchor system must be reliable.
The secret to successful fishing
Use feeders of different sizes. Start with the big ones to create a table, then switch to the small thimbles so you don't overfeed the fish, but keep it at a point.
Comparison of popular models and brands
The market offers a variety of solutions, from budget Chinese products to professional Japanese tools, and to help you choose and buy an onboard feeder from a boat, we have compiled a comparative table of popular models available on the market.
| Model | Length (m) | Test (g) | Materials | Features |
|---|---|---|---|---|
| Salmo Diamond Boat | 1.80 | 40-100 | carbon | Removable tops, SIC rings |
| Volzhanka Bordeaux | 1.65 | 20-60 | Composite | Budget, reliable, soft system |
| Flagman Boat Strong | 2.10 | 60-120 | carbon | Reinforced rings, for flow |
| Kaida Teleskop Boat | 1.50 | 30-80 | Fiberglass | Telescopic, unkillable |
Model from Salmo It's a classic of the genre, it's light, it's sensitive, it's perfectly balanced, but carbon is very delicate. Volzhanka It offers a more affordable option that will forgive the beginner mistakes in transportation. Flagman with reinforced rings.
And the telescopic variants, which are the least space in the boat, which is critical for inflatable PVC boats, where every centimeter counts, but telescopes are worse and heavier than plug-ins.
Installation and storage of gear in the boat
Proper placement of gear in a boat is not only a matter of convenience, but also of safety. Chaotic fishing rods can catch on the motor, oars or clothing of the fisherman. For onboard feeders, there are special holders that are attached to the boat or to the transom.
For PVC inflatable boats, vacuum-suction holders or those attached to stringers (inflatable tubes) are ideal. It is important that the mounting does not damage the boat material. Metal boats allow the use of magnetic holders or mounts on bolts.
⚠️ Warning: Never leave rods just lying on the bottom of the boat without fixing. In a sharp maneuver or wave, the gear may fall overboard along with the coil and feeder.
When stored in the off-season, the on-board rods are better disassembled. Telescopes should be dried in the decomposed form to avoid mold inside the knees. The legs of the plug rods are recommended to be lubricated with paraffin or special lubrication for corks so that they do not "stick" to each other during downtime.
Boat safety is more important than convenience: use reliable rod mounts to avoid PVC punctures or loss of tackle.
Frequently Asked Questions (FAQ)
Can I use regular spinning for onboard fishing?
Technically, you can if it's short (up to 1.8 m) and has a suitable test. However, spinning wheels are usually fast and are not designed to constantly monitor the nod or work with heavy feeders at depth.
How long should the leash be when fishing from a boat?
The length of the leash depends on the activity of the fish and the strength of the current. The standard range is from 30 cm to 1 meter. On a strong current, the leash is made shorter so that they do not blow away from the forage spot.
Do I need a sonar for onboard feeder fishing?
It's not a mandatory device, but it's a very desirable device, and it allows you to see the bottom relief, the presence of fish, and precisely position the boat above the eyebrow or the hole, which greatly improves the efficiency of fishing.
Which line is better to put: a wicker or a monophile?
For depths of more than 4-5 meters, it is definitely a wicker. It does not stretch and transmits a bite instantly. Monophile only makes sense to use in shallow water or when fishing for very careful fish, when the stealth of the tackle is important.
⚠️ Warning: When fishing from a boat, always carry a knife to cut the line. A tangled wicker can be a serious problem if the fish is dragged under the boat.