Fishing bream from a boat to a ring is one of the most lucrative and gambling ways to fish on large rivers with strong currents. The essence of the method is that the feeder with bait sinks to the bottom and is held by a powerful stream, creating a long plume that collects the fish. The main line with a cargo-ring slides along this feed thread, delivering the bait directly to the table of active fish.
Many anglers mistakenly believe that high-quality gear can only be bought in the store, but store options often sin poor quality metal or improper geometry. A homemade ringIt's a lot more efficient than the weight of your feeder, and in this article, we'll look at all the details of making the perfect tool, from the choice of alloy to the intricacies of rod assembly.
The main advantage of self-manufacture is that you can create a versatile tool that won't get stuck at the bottom or, conversely, too quickly to tear the current. You can adapt the hole diameter to the thickness of the main line, which is critical for the right cut. Let's take a step-by-step look at the process of creating this unique device.
Working principle and gearing
The rig "ring" is a massive loader-limiter that moves freely along the main line coming from the feeder. The key element And what you see here is the shape and weight of the ring, which should be lying on the bottom, but when you cut it, it's easy to get off the ground, and the elevator design is like this: you lift the feeder, the ring slides up the fishing line, and you fish it without mixing up the gear.
It's important to understand the physics of the process: the current presses the feeder line to the bottom, forming a strained string, and the ring is put on this string and its weight fixes the hooks with the bait in the bottom layer, where the bream feeds, and if you make the gear too light, it will be demolished, and it will lie on the feeder line, preventing you from cutting. The right balance - the key to success.
⚠️ Warning: Never use rings with an internal diameter well above the thickness of the feeder line, which will cause the ring to "walk" along the fishing line, get confused, and create false bites that you cannot implement.
There are two main types of construction: non-removable rings and detachable rings (often called "eggs" or "slit ring"). For beginner anglers, it is better to start with the manufacture of the car. plug-inBecause it allows you to change the fishing site without pulling a heavy feeder on board, and it saves you a lot of time and effort.
Selection of materials for manufacture
The first step in creating a quality gear is to find the right metal. lead Because it's so dense and soft, it makes it easy to process the workpiece, but pure lead is too soft and can deform when it hits a rocky bottom, so skilled craftsmen often use lead alloys with a little tin or antimony added.
You can use old batteries, remelted loaders, or even plumbing lead to cast the ring, and it's important that the metal is cleaned of dirt and oxides. aluminum For this purpose, it is categorically not suitable because of its lightness, and steel will require too complex processing to give the desired shape and weight.
- 🎣 Lead. - the main material that provides the necessary weight at compact dimensions of the product.
- 🔩 Steel wire - will be required to create an axis or a fixing element in connector models.
- 🛠️ File and file. - necessary for finishing the edges so that they do not cut the line.
- 🌊 Waterproof paint - used to mask the loader and protect the metal from oxidation (optional).
When choosing the shape of the workpiece, you should consider that the classic ring is shaped like a flattened bagel. This geometry ensures a stable position at the bottom: it does not roll like a ball, and does not stand on the edge like a flat puck. Wall thickness The future product should be sufficient to withstand the loads when catching large fish.
Drawing and casting process of the ring
Making begins with creating a mold. The easiest method is to cast into sand or clay, but for a home craftsman, a plaster-shaped option is more available, or even a brick-cutting template. The outer contour is usually 55-65 mm in diameter, and the inner diameter of the hole is matched under the feeder line (usually 1.5-2 mm).
The process of smelting lead requires caution: the metal is heated in a metal mug or bucket until it is completely melted, removing the resulting stain; it is important not to overheat the lead so that it does not start to burn out and become brittle; the pouring into the prepared form is made quickly and confidently to avoid voids.
The Secret to Perfect Shape
To get a smooth surface without sinks, the mold (especially if it is made of gypsum or sand) must be warmed up and slightly lubricated with engine oil before pouring lead, which will also prevent the metal from sticking.
If you make a severable ring (eggs), the technology becomes more complicated. You need to cast two halves or one solid workpiece, which you then have to carefully cut through the metal without reaching the end and fit a locking mechanism. Often, as a hold, you use a spring from a ballpoint pen or an elastic steel plate.
| Parameter | Meaning for quiet water | Meaning for strong current | Importance for night fishing |
|---|---|---|---|
| Ring weight | 40-60 grams | 80-120 grams | 60-80 grams |
| Diameter external | 50 mm | 60-70 mm | 55 mm |
| Diameter of the hole | 2.0 mm | 2.5-3.0 mm | 2.0 mm |
| Shape of section | Circle | Oval (fluid) | Circle |
Once the workpiece has cooled, it must be removed and carefully treated, the edges of the hole through which the line passes must be perfectly smooth, and any barb will damage the expensive wicker or monolescence, which can lead to the rupture of the gear at the most inopportune moment.
Making a fishing rod for a ring
The ring itself is just part of the system. To catch efficiently, you'll need a special rod, often called a "board," which is a short but durable rod that is 1.5 to 2 meters long, and it's inconvenient to use long spinnings from a boat because it can confuse the gear against the side or neighbors.
You can make the form yourself from an old spinning, sawing off a comet, or buy a ready-made rod, and the key requirement is the presence of a rigid whiplash that allows you to make a confident cut at a depth of 5-10 meters. nod in such gear is usually not used, since the bream peck is transmitted directly to the hand or visible by the tension of the fishing line.
- 🎣 Coil - a simple inertial "Nevskaya" or a cheap non-inertial meat grinder of 3000-4000 size is used.
- 🧵 Leska - the main line with a diameter of 0.3-0.4 mm, leashes of 0.2-0.25 mm 30-50 cm long.
- 🪝 Hooks. - are selected for the size of the bait, usually No. 8-12 according to the international classification with a long forearm.
The way to install the gear is to have a vertebral line at the end of the main line, which is fastened by a ring through the carbine, and then one or two leashes are tied below the ring, and the distance from the ring to the first hook should be such that the gear is not confused when lowered, but is in the zone of the bait plume.
Use fluorescent fishing line for leashes when fishing at dusk. Bream is not afraid of glowing threads, and you will find it easier to untangle the gear in the dark.
Feed: The heart of your tackle
Without a proper feeder, ring fishing makes no sense. The feeder must be large enough to hold enough bait for a long period, and have holes of the appropriate size. Too small cells will not allow the bait to wash out, and too large will empty the feeder in 5 minutes.
The best option is a cylindrical mesh feeder made of metal or plastic with a large cell (10-15 mm), the load must be placed inside so that the feeder itself does not blow away, and often fishermen use stones found on the shore or special lead pancakes.
An important element is a float marker that shows the location of the feeder on the surface of the water, and it is attached to the phala (cord) that holds the feeder. Bright color The float will help you not to lose the catch point in the wave or in poor lighting.
⚠️ Warning: Never tie the feeder line directly to the boat. If a large fish jerks or gets caught, this can lead to the boat tipping over, use a separate uncoupling cord or hold the tile in your hand across the side.
The bait mix must be heavy and inert. Adding clay or soil from the shore is necessary so that the stream of feed goes strictly down, and not carried away by the current to the side.
Fishing tactics and safety
The fishing process starts with placing the boat across the stream or at an angle so that the gear doesn't get tangled under the bottom, the feeder goes vertically from the side where the angler is sitting, and once the feeder has reached the bottom, the line is pulled and fixed, and now you can lower the gear with the ring.
The ring is put on the fishing line of the feeder, and the fishing rod goes into the water. You feel the load lying down. Now your task is to pick out the slack of the fishing line and fix the fishing rod. The pecking of the bream is usually confident: the nod (if any) bends, or the fishing line sags if the fish comes at you. The slash should be short and sharp.
☑️ Checking before getting on the water
Special attention should be paid to safety on the water. Ring fishing requires constant attention and quick reactions. Having a life jacket is a must, even if you are a great swimmer. The boat must be stable and the anchor must hold a position.
It is critically important to remember: when fishing from a boat alone, it is strictly forbidden to use more than one tackle (one feeder and one fishing rod), since the risk of entanglement and loss of control over the situation increases many times over.Once the fish is caught, the ring is pulled up to the surface, but not removed completely from the water so as not to scare the flock. The bream is quickly brought to the boat, taken in the suction and sent to the cage. The feeder during the fishing, try not to jerk, so as not to scare the fish that came.
The success of the ring fishing depends on 80% of the boat being properly positioned relative to the jet of bait, and if you don't get into the plume, the fish won't work, no matter how much you change the bait.
Frequently Asked Questions (FAQ)
Can I use the ring without a boat?
It's theoretically possible to catch from a bridge or a pier where the current is strong and vertical, but from shore, this method is ineffective because the feeder line will fall to the bottom at an angle, and the ring will not be able to slide freely to hooks.
What diameter of the fishing line is better to use for a feeder?
Optimally use a capron cord or fishing line with a diameter of 0.8-1.2 mm. a thinner line will sail strongly on the current, taking the feeder to the side, and a thicker one will create excess resistance and make noise in the water.
Why is the ring stuck in the feeder?
This happens if the diameter of the hole in the ring is too large for the feeder line, or if the feeder has defects on top, and the reason may be too long a leash, which gets tangled around the feeder line.
Do I need to feed the dot manually?
When using a volumetric feeder (5-10 liters), no additional feeding is required. The feeder works as a constant source of food. Hand-feeding only makes sense at the beginning, to quickly collect fish.
How do you make a gear noiseless?
Use soft wickers, grease the line with silicone, avoid metal rings that beat against the side of the boat, the main thing is smoothness of movement and no slaps on the water.