Operation of the inflatable floating craft imposes its own, special requirements for the placement of any additional equipment. Fixing for sucker In a boat, PVC is not just a convenience accessory, but a safety feature that is often ignored before the first large catch, and the situation where a captured fish, already brought to board, is de-hooked and goes into the abyss due to the lack of a net at hand, is familiar to many.
The problem is that the classic metal holders used on rigid housings can damage cylinders. fisherman's-placeSo you can keep the poop on hand, but you can't get in the way of rowing or motor control, and you can have a good space to focus on your catching, without having to worry about finding your gear.
Choosing the right fixator depends on many factors: the type of fishing, the design of the boat and the personal preferences of the owner. There is no universal solution suitable for all models of inflatable boats, so it is important to take into account the geometry of cylinders. We will look at the various options for mountings, their advantages and disadvantages, and also give step-by-step instructions for safe installation.
Criteria for selecting the holder for the inflatable board
The first thing to look for when looking for the perfect holder is the material of its manufacture. Aluminum alloys and stainless steel are high strength, but require the processing of all the edges. Any roughness or sharp angle can be fatal to the skin. polyvinyl chloridePlastic models are lighter and safer to carry, but can yield in durability under extreme loads.
The second critical parameter is the way that you lock, and the market offers solutions that are attached to a transom, pasted in a floorboard, or fixed to belts that span cylinders. transom anchorages They're popular because they don't take up space inside the cockpit, but they limit the maneuverability of the motor. Internal holders are easier to access, but require careful seating so they don't get stuck with their feet or tackles.
It's also important to consider the diameter and length of the handle of your podsuck. Some holders have a fixed cell size, others have an adjustable clamping system. If you plan to use several different nets, you'd better choose a versatile one. The reliability of fixing the handle in a storm or when a boat rolls sharply is another factor that you can't discount.
- 🔍 Material: Aluminum, plastic, composite or stainless steel – the choice depends on the balance between weight and strength.
- 🔒 Type of installation: Stationary (pasture), temporary (belts, suckers) or transom.
- 📏 Compatibility: The diameter of the handle of the sucker and the possibility of adjusting the angle of inclination.
And ergonomics, too, should be placed so that you can safely pull out the suction with one hand and cut or grab the fish, too high can cause the handle to lose balance, too low can cause the handle to get stuck in the gear, and the ideal attachment point is within the direct reach of the sitting angler.
Types of fasteners: from transom to belts
The most common option is transom holders, which are attached to the top edge of the transom using screws or powerful clamps, which is ideal for boats where the interior space of the cockpit is limited, but when you install it, you need to make sure that the holder leg will not touch the lower unit motor when it turns or reclines. Tranza installation Often requires drilling holes, which is unacceptable for some PVC boat owners.
An alternative to drilling is belt or sling mounts, which cover a cylinder or a stiffener (kilson) and are fixed by fastexes or buckles, the main advantage is mobility, you can easily move the holder to any convenient place or remove it altogether when it is not needed, while the load is distributed over a large area, which minimizes the risk of damage to the cylinder.
There are also glued glasses that are mounted directly into the floorboard (floor) of the boat, which provides maximum rigidity of the structure, but requires a professional approach and the use of special glue for PVC. The mistake when pasting can lead to the removal of the element with a piece of floor, which is unacceptable on the water.
The dangers of cheap plastic clamps
Cheap plastic clamps, which come with some budget holders, become brittle in the cold and can burst when large fish jerk. Always check the quality of the plastic or replace them with reinforced metal counterparts.
When choosing the type of fastening, it is important to consider the operating conditions. For fishing in calm water, all options are suitable, but for large areas where wave is possible, the maximum rigid fixation is required. A suction dangling on a long leg can become a dangerous projectile. short-leg It is preferable for unstable inflatable structures.
Instructions for safe DIY installation
The process of installing the mounting depends on the type chosen, but the general safety principles are the same for all options. If you choose to install on the belts, first thoroughly wipe the surface of the cylinder from dirt, sand and moisture. Using dirty belts can cause abrasive particles to rub against the fabric when the boat moves, causing micro-traumas of the coating.
For transom fasteners that require drilling, special metal and wood drills (depending on the transmunian material) must be used, and the holes must be sealed to prevent moisture from entering the transmunic structure, a critical step, as water trapped inside the plywood transmunic will cause it to swell and rot.
☑️ Pre-installing check
When tightening bolts or screeding belts, it is important to observe moderation. Excessive force can deform the balloon or push through the fabric. The fastening should sit tightly but not crash into the material. After installation, be sure to test: pull the mounted holder hard in different directions, simulating the jerk of the cut fish. If the structure luftites or slides, the installation is not well done.Failure to comply with installation technology It could cost you your catch and equipment.
Use wide washers or special plastic nut pads when attached through a fabric or a thin transom, this will increase the contact area and prevent the material from pressing under load.
The final step is to check compatibility with other equipment. Make sure that the handle of the suction stick inserted into the holder does not block access to the runduks, fuel tank or engine control lever. Also check whether the structure of the oars does not affect the paddle when rowing. Safety and usability are the main priorities of any modification of the boat.
Comparison of materials: which is better for PVC?
The choice of material holder directly affects its life and safety of the boat. Below is a comparative table that will help determine the best option for your conditions.
| Materials | Weight. | Strength | Safety for the board | Resistance to corrosion |
|---|---|---|---|---|
| Stainless steel | Highly | Very high. | Requires edge treatment | Great. |
| Aluminum (anodized) | Medium. | High. | Medium (softer than steel) | Good. |
| Plastic (ABS, polyamide) | Low. | Medium | High. | Great. |
| Composite (carbon) | Low. | High. | High. | Great. |
Stainless steel is the best choice in terms of reliability, but it is heavier and more expensive. Aluminum is the middle ground, but requires careful inspection for oxide chips. Plastic and composite materials are becoming more popular due to its light weight and inertness to water. However, at low temperatures, some plastics can become brittle.
⚠️ Warning: When using metal holders, always check the quality of welds and joints. Even a microscopic barb on metal under the influence of vibration and water works as a blade that can damage the balloon.
If you're going to metal, you should go through all the joints and edges with fine sandpaper and cover them with a layer of epoxy paint or varnish, and this simple procedure will significantly reduce the risks, and you should also consider that the metal in the sun is very hot, and taking on a hot handle holder can be unpleasant.
Maintenance and maintenance of fittings
Any equipment on the boat is exposed to aggressive environmental influences: salt water, ultraviolet light, temperature changes all test materials for strength. Regular maintenance of fasteners will prolong their life and preserve the neat appearance of your boat. After every fishing, especially on salt water, it is recommended to rinse metal elements with fresh water.
Plastic elements can fade under the sun, losing their elasticity. Periodically check the condition of the belts and plastic fasteners for cracks. If you notice that the plastic has begun to crumble or the belts have worn out, they should be replaced. Preventive substitution The cost of worn-out items is cheaper than buying a new sucker or repairing a boat.
Regular lubrication of mobile joints (if any) with silicone lubrication will prevent acidification and creaking, ensuring smooth operation of the mechanism in any season.
Keeping a boat with metal holders installed in a rolled-up form is not recommended unless the design provides for it. Rigid elements can create stress points on fabrics during long-term storage in a compressed state. Removable models are better dismantled and stored separately in a dry place.
Frequent errors in selection and operation
One of the most common mistakes is to buy a sticker by eye, without considering the actual size of the handle of the sucker, and the result is that a thin hand hangs in a wide glass, and a thick one just doesn't fit. Always bring a sucker when choosing accessories or know exactly the diameter of its handle. Universal models with rubber liners help solve this problem.
Another mistake is to install the holder in the area of active legs or tackles, and the fisherman may accidentally touch the handle of the podsuck when throwing the spinning, which will lead to loss of bait or even injury. Security zone You need to be free of unnecessary protruding objects around the workplace, so you plan to place the equipment so that the movements are natural and nothing interferes with the maneuvers.
- ❌ Ignoring checking the fasteners before going to water.
- ❌ Use rusty bolts that can stain clothes and tackles.
- ❌ Installation of the holder too close to the sharp corner of the cylinder or transmolent.
Remember that sucker is not only a tool for fishing, but also a safety net. In an emergency (for example, if a person falls overboard), a securely secured and quickly available bugor or sucker can save lives, so you need to take the selection and installation of this element seriously.
Can you use a car holder for a fishing rod as a mount for a sucker?
Theoretically, if the diameter of the handle is the same, but this is not recommended. Car holders are not designed for lateral loads and vibration on the water, and can also have aggressive spring mechanisms that damage the handle of the sucker.
How to remove a stale metal handle from the holder?
If the handle is jammed (often due to corrosion or dirt), do not use excessive force to avoid damaging the boat. Try pouring WD-40 joint or similar penetrating lubricant, waiting 10-15 minutes, and then gently scrolling the handle. In extreme cases, you can slightly heat the holder's glass (not the handle itself!) so that the metal expands.
Do I need to lubricate the holder's threaded connections?
Yes, you must. Use graphite or copper thread lubricant to prevent bolts from boiling. This is especially true in salt water, where corrosion is rapidly developing. Regular lubrication will allow you to easily dismantle the mount at any time.
Does the suction mount affect the load capacity of the boat?
The holder itself weighs a little (100 to 500 grams), so it has little impact on the overall load capacity. However, if you install a massive stainless steel structure with additional elements, this should be considered when calculating the maximum load, although the contribution will be minimal.