Fishing with the use of a boat opens access to the most promising fishing points, but requires competent organization of space. Spinning anchorage And not only is it a budget saving, but it's also an opportunity to create the perfect ergonomic knot for your angling style. Unlike factory-based, all-in-one solutions, homemade designs take into account the specific features of your boat, the location of the cans and the transom.
Incorrectly fastened gear can cause the loss of an expensive rod or even damage the balloon, which is critical for water safety. stainless steel or sea-aluminumAvoiding the cheap silumin that is often found in budget store models, which is especially important when used in salt water or in aggressive environments.
The process of creating a holder requires a minimum set of tools and basic skills in working with metal or plastic, the main thing is to understand the principle of load distribution and the features of attachment to soft sides or hard transom. In this article, we will discuss all the steps from the selection of the drawing to the final installation, so that your fishing is comfortable and safe.
⚠️ Warning: Any holes in the cylinders of the PVC boat should be sealed with a special glue for polyurethane fabrics, otherwise the structure will lose buoyancy.
Selection of materials and tools for manufacturing
The first step is always to select components that will come into contact with water and carry loads, and the support must be strong, but light, so as not to overload the cylinders. tubular is a polypropylene pipe with a diameter of 20-25 mm, as it does not rot, is easy to process and perfectly tolerates ultraviolet light.
For metal elements such as fasteners or rotary mechanisms, the brand’s aluminum is best suited. D16T stainless steel AISI 304The use of a regular black steel is unacceptable, because it will rust after the first season, spoiling the appearance of the boat and creating pockets of corrosion on the fittings. sewer-pipe PVC diameters 50 or 110 mm.
Use only stainless bolts, nuts and washers as fasteners. A conventional black fastener will quickly become unusable. To seal the passage of bolts through a cylinder or transom, you need two-component polyurethane adhesive, for example, Claiberite or Uranuswhich provides an elastic and water-resistant seam.
The toolkit depends on the technology you choose, but the basic kit will remain the same: you will need a metal hacksaw or a Bulgarian, a drill with a set of drills, burrs removal files and a marker for marking. If you work with metal, you will need a welding machine or a powerful soldering iron for plastic.
- 🛠️ Metal knife or pipe cutter for accurate cutting of blanks.
- 🔩 Drill and drill on metal/plastic to create mounting holes.
- 📏 Roulette, coal and marker for accurate marking of parts.
- 🔨 Fillers and sandpaper for processing edges.
Design features of holders for PVC boats
There are several basic types of fasteners, each with its own advantages depending on the fishing conditions. stationaryIt's a rod that is rigidly fixed to a cylinder or a jar, and it's easy to make, but it limits the mobility of the angler, because the rod is always in one spot.
A more advanced solution is a rotary mechanism that allows you to change the angle of inclination of the spinning, which is especially true when trolling or catching large fish, when you need to quickly change the vector of application of force, such designs often based on hinge joints or use ready-made rotary knots from car mirrors or furniture fittings.
Why is the angle of inclination important?
The angle of the holder's tilt affects the wobblear or the glitter when trolling. Too high can lead to a "screw" of the bait, and low can lead to a dip to unacceptable depth or a hook to the bottom. The optimal angle is considered to be at which the rod form is 15-20 degrees with the water surface.
Inside the hidden block: The angle of the holder's tilt affects the wobbler or the rays when trolling. Too high can lead to a stop at the bait, and a low one to a dip to an unacceptable depth or a hook at the bottom. The optimal angle is the angle at which the rod form is 15-20 degrees with the water surface.
Also worth considering is the option of mounting on a transom, which is suitable for boats with a rigid rear beam. Transs holders do not require drilling cylinders, which keeps the boat tight. However, they can interfere with the control of the engine, so they require careful adjustment of height and location relative to the lower unit.
⚠️ Warning: When installing holders on inflatable tubes, avoid sharp edges on contact areas so as not to damage the PVC fabric when frictioned or pumped.
Manufacture of a simple holder from a polypropylene pipe
The most affordable and quickest way to make a reliable mount is to use a plumbing polypropylene, which requires a 50 mm diameter, about 15 cm long, and a cap of the corresponding diameter, which can withstand the weight of powerful spinning coils and is not afraid of water.
The process starts with cutting the pipe at an angle, and if you want the rod to stand upright, the cut is perpendicular, and to create a 15-20 degree tilt that is considered optimal for most fishing, the end of the pipe is cut at an appropriate angle, and you can do this with a kerb or you can carefully mark the cutting line with a marker.
☑️ Holder assembly procedure
The bottom of the glass can be made from the same pipe by welding a stub, or carving a round pen of dense rubber or plywood soaked in olifu, fastening to the boat through a welded or glued pad, and a rectangular piece of plastic or aluminum that sticks to the cylinder is a great site.
- 📏 Measure 150 mm from the edge of the pipe and make a mark.
- ✂️ Cut the pipe at the right angle using a hacksaw with a small tooth.
- 🔥 Melt the edges with a lighter or hair dryer to remove sharp burrs.
- 🧪 Degrease the surface before sticking to the platform.
Reinforced design with a rotary mechanism
For those who value comfort and functionality, a more complex rotary knot scheme is suitable, based on a metal pipe or profile that is attached to the glass through a clampe or flange, the turning mechanism can be borrowed from old computer equipment, car holders for smartphones or buy a ready-made hinge at a construction store.
The key to this system is the rotational axis and the position lock. The axis is often used as a bolt M8 or M10, passing through two plates. Between the plates you need to install a friction washer of dense rubber or fluoroplastic, which will provide resistance when turning, not allowing the rod to dangle on the wave.
To fix the angle of inclination, you can use a spring-loaded pin that enters the holes in the holder's arc, or a simple screw lamb that presses the pipe against the bracket. The second option is easier to implement yourself. Metal parts are necessarily painted with powder paint or covered with epoxy soil to protect against corrosion.
The finished structure is mounted on a solid foundation, which is then attached to the boat. It is important to check the amplitude of movement: the spinning should be freely in and out of the glass, and the holder should not touch the sides or equipment when turning.
Comparison of installation methods: glue, bolts or Velcro
The choice of how to attach the holder to the hull of the boat depends on the design of the boat and your preferences. Each method has its pros and cons, which must be considered before starting work. Below is a comparative table of the main methods of fixation.
| Mounting method | Reliability | Difficulty of installation | Impact on the boat |
|---|---|---|---|
| Polyurethane glue | High. | Medium (requires drying) | It only breaks integrity when dismantled. |
| Bolts through the cylinder | Maximum | High (needs sealing) | Requires slugging holes |
| Velcro straps (Velcro) | Low (for light fishing rods only) | Minimum | Safe, doesn't spoil the fabric. |
| Twin-twin rods | Medium/High | Low. | Safe for PVC, need a place on the transom |
The adhesive method is considered the gold standard for PVC boats, and it provides a monolithic bond that is not afraid of vibration and water, but it is impossible to dismantle such a holder without damaging the fabric. The bolt connection through the cylinder requires careful sealing with washers and glue, but allows you to remove the structure if necessary.
The use of Velcro straps is only justified for temporary solutions or very light tackles, and on a serious wave or when a large fish is jerking, this fixation may not be possible. Strubcines are good for transom boards, but can interfere with the installation of the engine if the boat is small.
⚠️ Attention: Before drilling holes under bolts, be sure to apply markings on a pumped boat, since in a deflated state the geometry will change and the holes can "go".
Step-by-step instructions for installation on a cylinder
The mounting of the holder on board the boat is the most important step, requiring care. First, you need to determine the optimal place of installation. It should be easy to access by hand, but not interfere with rowing or moving on the cockpit. Usually, holders put on the sides just ahead of the seats (banks).
The surface of the PVC at the installation site is carefully degreased with alcohol or a special solvent for PVC. Then the first layer of glue is applied to the fabric and to the back of the holder (platform). After drying the first layer (usually 15-20 minutes), a second one is applied, and the parts are joined with a strong press.
Sticking sequence:1. Surface cleaning (fine grain sandpaper).
Degreasing (acetone/alcohol).
3. Applying glue layer 1 -> Drying 20 minutes.
4. Applying glue layer 2 -> Drying 5 minutes.
5. Strong pressing of parts (waller).
6 Drying 24 hours until full polymerization.
If you've chosen a bolt mount, then after you stick the pad, it's further fixed by bolts. The holes in the cylinder under the bolts are also glued. The bolt is inserted outside, a wide washer and a nut are put inside. All threaded joints are preferably cut or used by growers.
The main secret of durability is the quality of surface preparation (cleaning and degreasing) is more important than the brand of glue itself.
Once installed, let the structure dry for at least 24 hours before first use. Check the strength of the fixation by trying to shake the holder with your hand. If it is dead, you can start fishing.
Safety and tackle care
Operating homemade holders requires periodic monitoring of their condition; plastic can become brittle with ultraviolet light over time, and metal can become covered with microcracks of corrosion; Regularly inspect the mounting sites for cracks or adhesive detachments.
When transporting a boat in deflated form, it is better to dismantle removable elements or protect them with a soft cover so that sharp edges do not damage the cylinders when packing. If the holder is not removable, make sure that all protruding parts are rounded shapes.
- 🧼 After each fishing, wash the holders with fresh water, especially after fishing in salt water.
- 🔍 Once a season, check the tightening of bolt joints.
- ☀️ Try not to leave the boat for long in direct sunlight unnecessarily.
Keeping these simple rules will prolong your tuning life and ensure water safety, and remember that a reliable mount is a guarantee that your favorite spinning will not sink at the most inopportune time.
Can I use wooden elements for the holder?
You can use wood, but only hard rocks (oak, larch) with very high-quality oil impregnation or yacht lacquer. However, wood is heavier than plastic, swells from moisture and requires constant maintenance. For PVC boats, this is not the best choice due to weight and the risk of rotting.
What diameter of the glass to choose for spinning?
The optimal internal diameter of the glass is 50-60 mm. This is a versatile size suitable for most spinning handles. If you use specific thick handles, the diameter can be increased to 70 mm, but then the thin rods will dangle.
Do I need to make a hole in the bottom of a water glass?
Yes, a hole in the bottom (drainage) is mandatory. The glass will get water from rain, splash or wet gear. If you do not drain, the rod will be constantly in the water, which can damage the coil or handle.
Will the plastic holder withstand a large pike?
A qualitatively made holder of polypropylene pipe with a wall thickness of 3-4 mm will calmly withstand a pike jerk up to 5-7 kg. The main thing is the reliability of the mounting of the pipe itself to the boat, and not the material of the glass.