Any fishing or walk on the floatboat It's much more comfortable when your hands are free and all the accessories are on hand. The right PVC mounting solves the problem of placing spinning, sonar, anchors, and even navigational devices. Unlike a hard transom or bottom, the board requires a special approach to fixing equipment because of its soft and movable structure.
The modern market offers many solutions, from universal holders to specialized platforms designed for specific models. PVC boatsIt is important to understand that improper installation or selection of poor quality material can lead to the loss of expensive equipment or, worse, damage to the cylinder itself. A critical factor in the choice is the compatibility of the attachment material with PVC fabric in order to avoid chemical reactions.
In this article, we will discuss in detail the main types of locks, methods for their safe installation and the nuances of operation in various conditions, you will learn how to turn your boat into a full-fledged fishing boat without violating the tightness and integrity of the structure.
Main types of inflatable board anchorages
All devices for mounting on board can be divided into several key categories depending on the method of fixation and destination. suckerHowever, for serious fishing or long crossings, more reliable solutions are required, such as platforms on belts or clamps covering a balloon.
The second type is rigid structures that can be integrated into regular structures. ring-ring These systems provide maximum stability, but often require factory mounts on the boat itself, and the third type is universal clamps with soft sponges that do not damage the fabric when compressed.
- 🎣 The rod-holders: designed to fix spinning at an angle or vertically, often have a rotary mechanism.
- ⚓ Anchor points: allow you to quickly drop anchor and fix falin without the risk of entanglement.
- 📟 Electronics platforms: flat areas for sonars, GPS-navigators and smartphones with spray protection.
- 🔦 Universal brackets: equipped with a standard threaded connection for mounting any equipment with an adapter.
The type of fish you choose depends on your tasks. If you're a troller, you'll need reinforced holders that can withstand the jerks of large fish. If you're an amateur fisherman, you'll need lightweight plastic structures to fish from shore or in standing water. aluminum Alloys are more durable, but heavier than quality plastics.
Manufacturing materials and their impact on durability
Aggressive aqueous environments, ultraviolet radiation and mechanical stresses dictate stringent material requirements. The most common solution is to use marine aluminium with anode coating. This material is not rusting, lightweight and strong enough. However, when in contact with certain types of PVC or adhesives, aluminum can oxidize, so manufacturers often use plastic or rubber pads.
⚠️ Warning: The use of conventional steel mounts without corrosion-resistant treatment is strictly prohibited. rust will not only spoil the appearance of the boat, but can also chemically destroy the fabric of the cylinder at the point of contact.
Plastic mounts made from ABS plastic or polypropylene are becoming more popular, completely inert to water and the sun, do not conduct current or heat up in the sun as much as metal, but at extremely low temperatures, some plastics can become brittle. Fiberglass And composite materials represent a middle ground, combining the strength of metal and the lightness of plastic.
Special attention should be paid to the elements that come in direct contact with the balloon, which can be nylon belts, silicone suckers or soft rubber linings. The quality of these components determines how safe the equipment will be used. Cheap rubber in the cold tans and can rub the fabric, and poor-quality nylon quickly loses strength under the influence of UV rays.
Instructions for safe installation of equipment
The process of mounting the balloon requires care and a certain sequence of actions. First, you need to choose the installation site. It should be easy to access, but not interfere with rowing, boarding a boat or engine operation. Often the optimal place is the junction of the balloon and the transom plate or the area of the stringers.
Before installation, the surface of the balloon should be clean and dry. If you use suction cups, they should be degreased. For belt fasteners, it is important to calculate the tension correctly: too weak fastening will hang, and excessive fastening can deform the balloon or squeeze the valve. When working with adhesive elements (if the model requires it), you must strictly follow the instructions for the time of polymerization of the adhesive.
☑️ Pre-installing check
After the physical installation, be sure to do a strength test. Try to pull the fastener sharply in different directions, simulating a fish jerk or a wave strike. Make sure the sharp edges of the metal or plastic do not touch the fabric. If you install a rod holder, check the angle of tilt: it should not rest on the opposite side when the boat rolls.
Comparative table of popular types of fasteners
To make the choice easier, consider the main specifications of the different types of fixers in a comparative table, which will help you quickly navigate the variety of proposals and choose the best option for your business. flyboat.
| Type of attachment | Materials | Difficulty of installation | Reliability |
|---|---|---|---|
| Suction cup. | Plastic/Silicon | Low. | Low (for mild static) |
| Belt (coverage) | Aluminum/Nylon | Medium | High. |
| On the leer rings. | Stainless steel/Plastic | Low. | Medium (depending on the rings) |
| glue platform | PVC/Aluminum | High. | Maximum |
| Clamp on board | Plastic/Resin | Low. | Medium |
As you can see from the table, adhesive platforms are as reliable as possible, but they are irreversible and require skill. Belt structures are the gold standard for most anglers, as they allow you to change the configuration of equipment depending on fishing conditions. Suction cups should only be considered as a temporary solution for calm water.
Nuances of the use of adhesive platforms
The installation of the adhesive platform requires careful surface preparation. You need to clean the cylinder area with fine sandpaper, degrease and apply a special glue for PVC (often polyurethane-based). It is important to apply glue to both the fabric and the platform itself, wait a specified time and press hard. Full polymerization takes up to 24-48 hours. A mistake in choosing the glue can lead to detachment of the platform along with a piece of the cylinder fabric.
Operation and maintenance of fasteners
Even the best fasteners require regular maintenance. After every fishing, especially in salt water, it is recommended to wash metal elements with fresh water. Salt accelerates the corrosion of even anodized aluminum and destroys plastic compounds. Periodically check the condition of belts and rubber linings for cracks or scuffs.
When storing the boat in a deflated state, it is desirable to dismantle removable mounting elements. Prolonged pressure of rigid parts on the crumpled fabric can lead to the formation of cracks and microcracks in the PVC material. If dismantling is not possible, make sure that there are no sharp corners at the contact point, and use additional soft pads.
Watch the condition of the threaded joints. Vibration when the motor is running or moving along the wave can unwind even well-tightened nuts. Using a thread lock or periodic lifting of elements is a mandatory maintenance procedure. Rust on screws can "stick" to aluminum, after which disassembly of the unit will be impossible without damage to parts.
⚠️ Warning: Never use petroleum-based lubricants (such as solidol or petroleum petroleum) to care for mounts on a PVC boat. Petroleum products break down the structure of polyvinyl chloride, making it sticky and unstable. Use only silicone lubricants.
Frequent errors in selection and installation
One of the most common mistakes is trying to save money and buy a universal mount "for all boats". The reality is that the shape and rigidity of cylinders from different manufacturers (see below).Nissamaran, Badger, hunterThe universal clamp may either not hold or may clamp the cylinder to a dangerous state.
Another mistake is ignoring the wind load: At speed or in a strong side wind, the sail of fixed objects (especially sonars with screens) increases many times; a weak holder may not withstand the load and fly out, dragging expensive electronics with him. Always choose fasteners with a margin of safety.
Tip: Before buying a complex multi-seat set of fasteners, make mockups of cardboard or foam and try them on a pumped boat, which will help you understand whether they will interfere with each other or row.
Also, beginners often forget about balance: placing heavy equipment (batteries, drawers) on just one side can lead to dangerous boat rolls; distribute weight symmetrically relative to the boat's diametrical plane; it's not just a matter of comfort, but also safety.
The main conclusion: The safety and functionality of the mount depend not so much on the price, but on the correct selection for a particular model of the boat and compliance with the rules of operation.
Questions and Answers (FAQ)
Can I glue the mount to the boat on my own if the factory unstuck?
Yes, it is possible, but it requires the use of a special two-part glue for PVC (polyurethane) the surface must be thoroughly cleaned and degreased. However, for holders under heavy loads (for example, for anchor), it is better to use belt or mechanical options, since the adhesive seam is a weak spot in dynamic jerks.
Will metal mounting damage the balloon in the cold?
Direct contact of cold metal with PVC at negative temperatures is undesirable. PVC becomes less elastic, and hard metal can push or rub the fabric when the cylinder is deformed. Always use intermediate rubber or plastic pads between the metal and the cylinder.
Will the plastic holder withstand a large pike or pike?
High-quality engineering plastic (ABS) has high strength on the kink. However, when catching large fish, the bending load can be critical. For trophy fishing, it is preferable to use aluminum holders with reinforced construction or models with an additional safety belt.
How to remove the suction cup without damaging the balloon?
Never pull the suction cup over the edge. Put your nail or flat object (like a coin) on the edge of the suction cup to get the air in. Once the pressure is equalized, it will be removed easily. If the suction cup is dry, wet the edge lightly with water.