You bought an anchored rum for your PVC boat, but you're not sure where to fix it properly? Installation errors can lead to the rupture of the rupture under load, damage to cylinders, or even loss of the boat on the current. 5 Best Places to Installsuitable types of glue, and Critical mistakes that 80% of newcomers make.

An anchor rim is not just a loop to anchor; it distributes loads when mooring, towing or parking on the current; an incorrect position can make a boat unmanageable or cause seams to rupture; we analyzed the experience of professional water-engineers and identified key rules to help avoid problems.

Why you can not glue the pome “in the eye”: the physics of loads

Before you grab the glue, you need to understand, What forces are working on the rim in different situations:

  • 🔹 Mooring to the pier - the load is horizontally directed, pulls forward or backward.
  • 🔹 Anchored parking lot - rum experiences vertical and lateral load from the current or wind.
  • 🔹 Towing Maximum dynamic loads, jerks up to 200-300 kg (depending on the size of the boat).

If the fry is placed too close to the transom, the boat will peck with its nose when it is towed, burrowing into the water, and if you attach it to the nose without considering the cylinders, the load will go on the seams, which can break, and the optimal position is calculated from:

  • 📏 The length of the boat (for models up to 3.5 m and over 4 m the rules are different).
  • 🔧 Designs of cylinders (round vs. V-shaped).
  • 💧 PVC materials (thickness and density).
📊 Where do you have an anchor rum?
On the nose.
On the transom.
On the sides.
I haven't installed it yet.

Top 5 places to install anchor dim: pros and cons of each

Let's see. fixationThe boat owners use Bark, frigate and corvetteEvery place has its own nuances:

Place of installation Advantages Deficiencies Suitable for boats.
Forest cylinder (top point) ✅ Optimal for mooring
✅ Minimum load on seams		 ❌ Uncomfortable for anchor (chains can scratch PVC)
❌ Risk of hooks during transportation		 Up to 3.5 m, with round cylinders
Airborne cylinders (at 1/3 of the nose) ✅ Uniform load distribution
✅ Convenient for towing		 ❌ It is difficult to attach to V-shaped cylinders
❌ Requires 2 rima (symmetrical)		 From 3.5 m, hard bottomed.
transom (centre) ✅ Convenient for anchoring and towing
✅ Minimum risk of damage		 ❌ Engine compartment load
❌ Could be in the way of management.		 Boats with a 5 hp engine.
Nose septum (between cylinders) ✅ Maximum strength
✅ Suitable for heavy anchors		 ❌ Complicated installation (you need to remove the balloon)
❌ Risk of damage to seams		 Boats from 4 m, with a strengthened nose
Bottom (at the transom, for towing) ✅ Perfect for towing.
✅ It doesn't interfere with fishing.		 ❌ Not suitable for anchor.
❌ Only for hard-bottom boats.		 Boats with inflatable keel

For most boats, the length 3.5 m combine optimally nose-mount (for mooring) and turret (for anchor) Model owners. Bark 380 or Frigate-360 It is better to avoid on-board installation - thin PVC may not withstand jerks when towing.

Check the thickness of the PVC at the anchorage (minimum 0.9 mm)

Clean the surface of dirt and fat (use acetone)

Choose a glue that is compatible with PVC (for example, Bostik 2402 or Polychloroprene)

Think about the trajectory of the cable (should not rub the cylinders)

-->

The quality of the glue depends on it. Will the rump withstand a load of 150-200 kg or break off at the first jerk?We tested 4 compounds on thick PVC samples. 1.1 mm (boat cylinder analogue) Corvette 420Results:

  • 🧪 Bostik 2402 - withstood 180 kg (PVC break, not seam) Best choice for professionals.
  • 🧪 Crystal moment — 120 kg (unstuck under dynamic load) It's only good for light crumbs.
  • 🧪 Polychloroprene glue (Tarckett) — 150 kgBut it requires a dryer.
  • 🧪 Superglue (cyanoacrylate) — 50 kgI'm not recommending it.

Use it for reliability. two-component (for example, Bostik 2402) and follow the instructions:

  1. Apply glue on both surfaces (spy and PVC).
  2. Let me dry. 10-15 minutes (to "Otlip")
  3. Then, put it in the back and put it in the back.60–80°C).
  4. Leave it under load on 24 hours. (minimum)
⚠️ Attention: If you put a snag on a boat that has already been operated, necessarily Remove the old layer of sealant or glue! Residues can reduce adhesion by 40%. Use a solvent. 646 mechanical cleaning (without damage to PVC).

Step by step: how to glue the pome without errors

Let's analyze the process on the example of installing a river on the bow balloon of a boat Bark 320You're gonna need:

  • 🔧 Base-fishing pond 5×7 cm (for example, Harkila or Alloy).
  • 🧴 Clay. Bostik 2402 or Polychloroprene.
  • 🧹 Acetone, rags, building hair dryer.
  • 📏 Line, marker, cargo 10-15 kg.

Step 1. Markup. Measure. 15–20 cm from the bow of the boat (for the model) 3.5 mor 25-30 cm (for boats) 4 m+Put a marker on the contour of the ribe. Make sure the spot doesn't get on the seams!

Step 2. Prepare the surface. Clean the PVC with acetone, then lightly shook the base of the smear and the place of attachment with sandpaper. P120 (This increases adhesion by 30%).

Step 3. Sticking. Apply glue on both surfaces, let dry, connect and warm up with a hair dryer. Place a load on top (for example, a battery). 12V 60Ahon 24 hours..

Step 4, check. After a day, try to tear it off with your rump hand, and if you don't, you can test it on water. 2-3 exits Avoid any big jerks!

What do I do if I'm out of shape?

If the rum is torn off with a piece of PVC, the damage site should be reinforced with a patch of the same material. Bostik 2402 If you have a damaged tank seam, call the service, self-repairing can be dangerous!

Common Mistakes and How to Avoid Them

Even experienced water-engines sometimes make mistakes that lead to breakdowns. TOP-5 misses And how to prevent them:

  • 🚫 Rivet instead of glue. Rivets tear PVC when you're under load. glue-only Or combine them with soft pads.
  • 🚫 Set-up. The stitches are the weakest part of the balloon. 5cm from the seam.
  • 🚫 Using a silicone sealant. It doesn't hold dynamic loads. polychloroprene or polyurethane glue!
  • 🚫 Neglect of the load when glued. Without pressure, the glue does not penetrate the pores of PVC.
  • 🚫 Fixing to a dirty surface. Fat spots or sand reduce adhesion by 50%.
⚠️ Attention: If you are installing a rat on a boat with keel (for example, Saturn or Zodiac), never attach it to the keel! This disrupts hydrodynamics and can lead to coup Use only cylinders.
💡

Before the first outlet to the water after installing the river, check it on land: tie the cargo to it. 30-40 kg And if you don't move, you can go out into the water.

Additional accessories: what will come in handy with the snail

Installing a riddle is only half the battle, and for safety and convenience, you'll need to:

  • 🔗 Rope or cable. Optimally. polyester diameter 8-10 mm (not stretched in water).
  • 🔒 Carbine with lock. Prevents spontaneous uncoupling of the anchor.
  • 🛡️ Protective pad. If the cable rubs against PVC, use a silicone tube or leather case.
  • 📏 Adjustable towing cable. For motor boats, length 3-5 m- With a shock absorber.

For boats that are often towed (for example, behind a boat), we recommend installing the transmutation use tow-arcIt'll reduce the load on the cylinders and improve handling.

💡

The most reliable fastening is a combination of glue Bostik 2402 And a soft pad of neoprene, which is a compound that can hold up to 250 kg dynamic load.

Overview of ready-made solutions: Rips from proven brands

If you don't want to mess with the glue, you can buy poppy with a pre-mounted mount. 3 popular models:

Model Materials Max, load. Features Price (2026)
Harkila Anchor Eye Stainless steel + PVC base 200 kg Self-adhesive base, suitable for PVC 0.9–1.2 mm ~1 200 ₽
Fishing slurry Galvanized steel 150 kg Requires glue, universal size ~800 ₽
Bark Professional Aluminum + neoprene pad 250 kg For boats with hard bottom, resistant to corrosion ~1 500 ₽

For budget boats (e.g., Frigate-330) fits the model from AlloyBut if you often walk on the current or tow a boat, it is better to overpay for the boat. Harkila or Bark.

FAQ: Answers to Frequent Questions

Can I install a rivet on a boat with rivets?

No, rivets. PVC breakout Only adhesive attachment or a combination of glue with soft pads is allowed, except for boats with hard bottoms (for example, aluminum), where you can use nut and sealant bolts.

How many rims do you need for a boat 4 meters long?

Optimally. 2 squirrel: one on the nose (for mooring), the second on the transient (for anchoring/towing). If the boat is used for trolling or fishing on the flow, you can add tarmac (one on each side).

How to remove old rum without damaging PVC?

Carefully tuck in a scaly plastic spatula soaked in acetone, then clean the glue residue with solvent. 646 Or mechanically (without pressure) If you have any traces, grind them with sandpaper. P400 And apply a thin layer of glue to level the surface.

Can I use epoxy glue for the squirrel?

Epoxy glue wrong For PVC, it's not elastic and it cracks when the balloon curves. polychloroprene, polyurethane or Bostik 2402.

What to do if the squirrels start to unplug?

If the rump has partially retreated, Don't try to glue it on top.Remove the old glue, clean the surface and re-stick the fracking with a warm-up hairdryer, and if the PVC breaks, install a patch of the same material.