Choosing a swimming facility is always about finding a balance between weight, capacity and price. Boat Aqua 320 For many years, it has been a leader in the low-cost inflatables segment, attracting the attention of both beginners and experienced anglers, and this domestically produced model has proven to be a reliable tool for getting on the water with minimal investment.
Many users are looking for this particular dimensional range, because it is considered universal. On the one hand, the length of 320 centimeters allows you to confidently hold the wave and course, and on the other hand, the dimensions still allow you to transport a boat in the trunk of a passenger car. Aqua 320Whether it is worth your attention this season.
It is worth noting that the popularity of the model has generated many modifications and disputes about the quality of materials. boat design It's been changing, and it's important to understand the differences between early and modern versions, and the right way to operate will significantly extend the life of the product.
Design features and materials
The basis for creating the body is a high-strength reinforced PVCUnlike cheap polyethylene, this composite is very good at handling temperature changes, ultraviolet light and mechanical stress, and the density of the fabric is usually around 750-850 g/sq.m., which provides good resistance to punctures against rocky bottoms or driftwoods.
Particular attention should be paid to the system. floor-floor (NDND) Unlike the plywood models, which require a hard floor assembly of aluminum or plywood boards, it uses a high-pressure cylinder, which makes it instantaneous: just pumped up, and the boat is ready to descend, but it has its own nuances in rigidity.
⚠️ Attention: When pumping the bottom of high pressure, carefully monitor the pressure gauge. Pumping in hot weather in the sun can cause joints to rupture or deform the valves, as the air inside expands.
Seams on high-quality specimens are made by tape method, which guarantees tightness for many years. Trans insert It is made of moisture-resistant plywood and painted with special paint to prevent the slipping of the legs. The attachment of the transom to the cylinders is carried out by reliable slings or metal brackets, depending on the year of the model.
The secret to the longevity of seams
The quality of the seam depends not only on the glue, but also on the surface preparation. The plant uses an activator that degreases PVC and creates a chemical bond with the adhesive compound, which is why artisanal repairs often last worse than factory design.
Dimension, weight and load capacity
For many aquatic motorists, the physical parameters of the vessel are critical, as they affect the logistics of trips. Boat Aqua 320 assembled has a length of 320 cm and a width of about 140-146 cm These parameters allow you to comfortably accommodate two adults with the necessary equipment.
The weight of the kit varies depending on the configuration, but usually ranges from 35 to 42 kg. This is a fairly light indicator that allows one person to carry the equipment to the water, although it is still more convenient to carry the assembled boat together. The model's load capacity is stated in the region of 400-450 kg, which with a margin covers the weight of two passengers and the engine.
| Parameter | Meaning | Note |
|---|---|---|
| Full length | 320 cm | Including inflatable tubes |
| Full width | 146 cm | Maximum cylinder width |
| Diameter of the cylinder | 36 cm | Provides good stability |
| Weight of an empty boat | ~38 kg | Without motor and equipment |
| Load capacity | 400 kg | data-sheet figures |
It is important to remember that the actual payload is always less than the passport. Operational safety It requires you to keep a buoyancy reserve in case of water getting in or an emergency, and you should not load the boards to the limit, especially when going out into open water.
The optimal load of the boat Aqua 320 is two people of average build and a motor with a capacity of up to 5 hp Exceeding this limit reduces speed and handling.
Performance specifications in water
Water behavior is the main criterion for judging. Aqua 320 It has a very good wave germination, a soft side that extinguishes impacts, which makes it comfortable to swim even with a little excitement, and it doesn't hit the water as hard-bottom boats.
But you have to remember sailing. High cylinders create an area that is easily blown away by the wind. When you use an electric motor or a low-power gasoline engine, you can notice drift. To compensate for this effect, experienced anglers use a cat anchor or special floating anchors.
- 🎣 Sustainability: The wide cockpit allows you to fish standing up, which is convenient for spinning players.
- 🌊 Driving specifications: On planing comes with a motor from 3.5 hp. with one passenger.
- 🔄 Maneuverability: The clutch is average, depending on the shape of the keel and the presence of redane.
When moving against the current, the boat behaves predictably if the weight is distributed correctly. Centrification It plays a key role: moving passengers or cargo to the nose or stern can significantly worsen the exit to planing. It is recommended to place heavy things (batteries, anchors) closer to the center of the diameter.
Installation of the motor and transax plate
The transom plate is the "foundation" for your engine. Aqua 320 It's made of multi-layered plywood, soaked in water-repellent compounds, and the standard departure of a transom is 381 mm (15 inches), which is the short lower unit of most outboard motors.
The motor is fastened by screw clips or rods. It is important to (regularly check) the condition of the fasteners, since vibration can weaken the puff. Security requires that the motor be additionally a safety cable attached to the fry bolt on the transom, in case of slipping of the rods.
The maximum recommended power of the motor for this model is usually limited to 5-6 hp Installation of a more powerful engine is possible, but requires caution. If you exceed the power, there is a risk of transone tearing off or loss of control at high speeds, which is strictly prohibited by the instruction manual.
⚠️ Warning: Never start the motor out of water or with a raised lower unit without a special nozzle on the water pump.
For electric motors, this boat is ideal because it is quiet and has no vibrations. Electric thrust is often mounted on the nose or transom, depending on the model of the motor. Light weight allows you to quickly dismantle the power unit when approaching shore.
Installation and additional equipment
Basic equipment usually includes the boat itself, the bag-pack, the pump, the remix and the seats (banks), but this may not be enough to fully operate. Accessories They can turn the basic model into a full-fledged fishing boat.
First of all, you should think about protecting the bottom: additional PVC linings or special carpets (linoleum) will save the cylinders from abrasion against sand and stones, and also popular transom wheels, which facilitate the movement of a motorized boat on the shore.
- 🛡️ Protective apron: It is applied to the nose, protecting against splashes and blows.
- 🪝 Holders of rods: They are mounted on board, freeing the hands of the fisherman.
- 💡 The hinged transom: It allows you to install a second motor or sonar.
And don't forget the attachments for navigation and safety, and the installation of sonar, GPS and running lights (if you plan to go out at night) greatly expands the boat's use, and all electrical appliances must be securely secured and protected from water.
☑️ Pre-season checks
Care, storage and repair
Durability boats Aqua 320 It depends on how you care for it, because PVC doesn't like to be in the direct sunlight for long periods of time, and it's pumped up, and UV light breaks down the polymer structure, making it fragile and faded.
After each fishing, the boat should be washed with fresh water, especially if you have been swimming in salt water or a body of water with a lot of tin. Sand and dirt left on the fabric work like an abrasive, rubbing the fibers when bending and inflating. Drying before packaging is a must.
Store the product in a dry, cool place, in a straightened or half-folded form, sudden temperature changes and storage near heating appliances are unacceptable. tenure Products can be 10 years or more.
⚠️ Warning: If the boat was stored at negative temperatures, it is forbidden to sharply inflate or bend it. Let the material warm to room temperature for 2-3 hours, otherwise PVC may crack on the folds.
In case of a puncture, you should not panic. The repair kit that comes with it contains everything you need to repair minor damage. For more serious damage, there are special two-component adhesives and patches that allow you to restore leakage even in the field, if you follow the technology.
To quickly look for a puncture at home, use a soap solution. Put on suspicious places and wait for bubbles to appear - this will indicate the exact location of the air leak.
Frequently Asked Questions (FAQ)
Is it possible to go to large water bodies on the Aqua 320 boat?
The only way to reach large bodies of water (Ladoga, Onega, large reservoirs) is calm and in close proximity to the shore, and this boat is not designed for open waves and strong winds because of its sailing and low board. For large areas, it is better to choose models with an inflatable keel and higher sides.
Which glue is best for PVC repair?
Polyurethane two-component adhesives (such as Kleyberg or specialty PVC adhesives for boats) are the best choice, creating an elastic seam that doesn't crack when the material is deformed. Conventional household adhesives like Momenta produce a rigid compound that can detach.
How many people can comfortably fit in a boat?
The Aqua 320 is a comfortable boat with two medium sized people, three adults only fit in an emergency, but this will critically reduce buoyancy and handling, making swimming a dangerous event.
Do I need to register this boat with GIMS?
According to Russian legislation, vessels weighing more than 200 kg (in running order) or with an engine power of more than 8 hp (5.88 kW) are subject to registration. Since the weight of the Aqua 320 is usually less than 200 kg, registration is not required when installing an engine up to 5 hp inclusive. However, laws may change, so current information should be clarified at the local GIMS office.