The choice of a boat for fishing or recreation on the water always begins with an analysis of the specific needs and operating conditions. Azimuth boat 330 NDND It is well positioned in the mid-sized inflatable keel boat segment, offering a balance between payload and mobility. The low-pressure inflatable floor design (LBBB) is a major change in how the vessel is assembled and transported, making it accessible to a wide range of water-powered operators.
Unlike models with plywood peyol, there is no need to drag heavy sheets and waste time docking them. PVCThe silk-based silk used in manufacturing is highly dense, which guarantees durability even when in contact with a rocky bottom or shell, and is ideal for those who value time and comfort in preparation for the launch.
It is worth noting that the versatility of this model allows you to use it both for quiet fishing in quiet bays and for passing small thresholds. Hydrodynamic properties The hulls provide a stable course, and the presence of quill over the length of the balloon It creates a rigid structure comparable to rigid-hull counterparts, and it's this design nuance that often becomes the deciding factor when choosing between different modifications.
Design features and materials
The basis of reliability of any inflatable boat is the quality of materials and assembly technology. Azimuth 330 It uses a five-layer reinforced fabric that is resistant to ultraviolet, fuel and mechanical damage, and the seams are made by hot welding, which eliminates the possibility of leakage even during prolonged use under load.
The key element here is the system. NDMAThe inflatable floor is made up of many cells that, when pumped, form a rigid plane, which not only eliminates the need for additional equipment, but also increases the overall level of the air. floatability The boards also have complex geometry, which ensures excellent germination on the wave.
It is important to take into account the pressure distribution in cylinders. To achieve optimal structural rigidity, the manufacturer's recommended values must be followed. Working pressure in cylinders should be 0.2 atm, while in an inflatable keel it can reach 0.25 atm to ensure maximum longitudinal rigidity.
⚠️ Warning: Never leave a fully pumped boat in direct sunlight unattended. Heating the air inside the cylinders leads to an increase in pressure, which can cause seams to rupture or cloth deformation. Lightly blow the air in hot weather.
The equipment used in the kit also deserves a separate mention. Brass valves Frog or Bravo (depending on the year of manufacture) provide tightness and ease of pumping, and the fastenings for cans and stringers are made with a margin of safety, withstanding dynamic loads when moving along the wave.
The secret of valve durability
To keep the valves longer and do not let air through, periodically lubricate rubber seals with silicone lubrication. This will prevent the rubber from drying out and the appearance of microcracks that are invisible to the eye but lead to a slow leak.
Dimension, weight and load capacity
When choosing a boat, physical parameters often become decisive, especially if transport is carried out by car or public transport. Boat Azimuth 330 The vehicle is 3.30 meters long, which is the “golden mean” for two or three people with a full set of equipment.
The weight of the kit is where the NDND is superior, the absence of heavy plywood slabs and aluminum profiles reduces the overall weight, and when assembled, the boat is packed in compact bags that can easily fit into the trunk of the sedan, making it attractive for single fishermen without a trailer.
- 📏 Length full: 330cm
- 📏 Full width: 146 cm
- ⚖️ Weight of the boat in the kit: about 36-38 kg (depending on the configuration)
- 👥 Passenger capacity: 3 persons
- 🎒 Cargo capacity: up to 450 kg
Distribution of the payload allows you to take with you a significant supply of gear, sonar, anchor and even a small fuel reserve. Specific load capacity The per passenger remains high, which ensures comfort and safety of boarding.
For comparison with analogues and understanding of the place of the model in the line, we turn to the table of specifications:
| Parameter | Azimuth 330 NDLD | Azimuth 300 NDLD | Azimuth 350 NDLD |
|---|---|---|---|
| Length, cm | 330 | 300 | 350 |
| Width, cm | 146 | 146 | 150 |
| Weight, kg | ~37 | ~33 | ~42 |
| Motor power (max), hp | 10-15 | 8-9.8 | 15-18 |
Driving qualities and compatibility with motors
The dynamics of the movement is what owners love the series for. AzimuthThe shape of the cylinders is designed to minimize water resistance and provide a quick exit to plane, and when loaded properly, the boat holds its course confidently even in lateral winds.
The choice of powertrain is a pressing issue, and for this model, the optimal power range is motors from 5 to 15 horsepower. Two-stroke engines Weight up to 25 kg is preferred due to the shifting of the center of gravity, but modern four-strokes are also successfully used provided that the transom angle is observed.
When installing the motor, you must take into account transom-angleIt's adjusted by pads or washer adjustments on the lower unit, and if you don't fit it properly, you'll either be nagging or you'll have too much differentiation on the stern, which will increase fuel consumption and slow down speed.
The maximum speed with a 9.9 hp engine and a single driver can reach 25-28 km / h. With full load, the speed drops, but the boat remains controlled. cross-board may not withstand increased load on the cut, which will lead to deformation or separation.
⚠️ Warning: When operating with a maximum power motor (15 hp), be sure to use the safety cable for the engine. Sharp shocks to the wave can cause the engine to lose overboard.
To improve driving performance when fully loaded, try to shift the seats (banks) a little forward, which will help unload the transom and facilitate the exit to planing, especially with low-power engines.
Comfort and internal equipment
Interior space Azimuth 330 It's ergonomically organized, and you have two inflatable seat cans that allow you to choose the optimal seating pattern, and you can lock the cans in your pockets or with a system. lyctros-licpaseThis prevents them from moving during the process.
For fishermen, the possibility of installing additional equipment is an important aspect, and the sides have liner cables for which to attach gear or lifeline. sonar and navigational devices.
Inflatable seat elements provide softness, but for long transitions, many users recommend using additional soft linings. The nose often has a knob or storage space protected from spray balloons.
- 🪑 Removable inflatable seats complete
- 🔒 Reinforced handles for carrying around the perimeter
- ⚓ A timber around the perimeter to protect against impacts
- 🛡️ Reinforced overhead keel to protect the bottom
It's important to keep the interior clean. Sand and small pebbles, when they get between the bottom and the mat (if used), work like an abrasive. Regular cleaning will prolong life. PVC material And it'll keep its aesthetic look.
☑️ Checking before getting on the water
Assembly, packaging and storage
Preparation process Azimuth 330 NDLD It's much easier to go down the slope than the plyols, you don't have to spend time laying the floor and mounting the stringers, you just have to spread the boat, pump the cylinders and install the cans, and the whole process takes 10 to 15 minutes, even for an inexperienced user.
It's important to keep the pump sequence going, so you blow the sides a little bit, then the keel, and then you finally adjust the pressure to the working values, so you can straighten the fabric evenly and avoid distortions.
Packaging requires care, and the boat must be thoroughly washed with fresh water, especially if it is operated in salt water. After drying (but not in direct sunlight!), the boat rolls from transom to nose. Curtailment It should be tight, but without fanaticism, so as not to create excessive pressure on the seams in the places of folding.
Keeping the boat in a case at room temperature is best. Avoid being close to sharp objects, chemicals and open fire sources. When stored in an unheated garage in winter, make sure the material is completely dry to prevent mold formation.
⚠️ Warning: Do not keep the boat rolled up for long periods (months) without periodically straightening, which can lead to the formation of persistent cloth cloth cladding and the destruction of the internal reinforcing layer.
The main advantage of NDND is the speed of assembly and the absence of heavy elements, which makes the boat ideal for mobile use and frequent trips to different water bodies.
FAQ: Frequently asked questions
Can I use the Azimuth 330 for sea fishing?
Marine use is possible, but with limitations. The boat is suitable for coastal areas and calm waters. However, salt aggressively affects the metal fittings and seams, and open sea waves can be dangerous for an inflatable hull of this size. After each outing, thorough washing with fresh water is required.
Which glue is best for puncture repair?
For repairs. PVC tissueThe two-component polyurethane adhesives (e.g. Radical, 88-NP or specialized adhesives for boats) are best used to create an elastic and water-resistant seam that can withstand deformation on water.
Do I need to register a boat with GIMS?
According to the current legislation of the Russian Federation, registration is subject to small vessels weighing more than 200 kg in running order or with an engine power of more than 8 kW (about 10.88 hp). Azimuth 330 If the engine weighs less than 200 kg, registration depends on the power of the installed engine. If the engine is more powerful than 10.88 hp, registration is required.
How to dry a boat after fishing?
Dry the boat in the shade, straightened or suspended upside down. Direct sunlight combined with moisture can accelerate the aging of the material. Make sure that all hard-to-reach places, especially under the stringers (if any) and in the valve area, are dried to avoid the appearance of fungus.
lifehack for packaging
To keep the boat in the trunk less space, you can use vacuum bags for clothes (with caution!) or just twist it very tightly, starting with maximum air removal through open valves, pressing your knee. But remember the risk of claws during long-term storage.