Spinning fishing is very different from just fishing from shore or even classic trolling, requiring constant catches of perspective points, frequent change of positions and the ability to maneuver even in difficult conditions, which is why the boat for the spinning driver becomes not just a means of getting the fisherman to the point, but a full-fledged mobile platform on which catch and comfort depend.
Many novice anglers make the mistake of buying the first inflatable vessel they come across without taking into account the specifics of anchoring and active wiring of the baits. The right boat allows you not only to comfortably position your gear, but also to safely anchor in windy weather. In this article, we will discuss the key aspects of choosing, designing and equipping a boat that will become your reliable partner on the water.
Criteria for the selection of a watercraft for active fishing
The first thing to consider when choosing is flooringFor spinning fishing, it is critical to have a hard, flat surface that allows you to stand and move confidently through the cockpit. Air Deck inflatable floorboards are lost here because they are too soft and unstable. The optimal solution is a floor made of sea aluminum or plywood covered with anti-slip film.
The second important parameter is cockpit-widthIf you plan to fish alone, a boat that is too wide will sail and be less manageable, but for tandem or additional equipment installation, width matters. Narrow models are less resistant to throwing, which can lead to dangerous situations or the loss of expensive wobbles.
⚠️ Attention: Don't skimp on the width of the transom. Too narrow a transom will not allow you to install a full sonar and transom motor, which is often necessary for accurate positioning at the point.
Also consider the material of cylinders. For spinning, where there is a high risk of catching the fabric with gear, it is better to choose high-density PVC with reinforcement. The optimal density of fabric for a spinning boat starts from 750 g/sq.m.This ensures the durability and durability of operation.
- 🎣 The presence of an inflatable keel or a rigid V-shaped profile for better handling on the wave.
- 🎣 Location of paddle switches: they should not interfere with the wiring of the spinning.
- 🎣 The presence of liner cables along the sides for fastening tackles and safety.
Inflatable boats against rigid hull
The perennial dispute between PVC and tin cans in the spinning context has its nuances: Inflatable boats benefit from mobility: they can be folded into the trunk of a sedan and delivered to the water itself, but rigid hulls (aluminum or plastic) provide better stability and allow high speeds without the risk of seasickness.
If you fish in large reservoirs where the wave often rises, a hard hull or boat with inflatable sides and a rigid V-bottom (RIB) will be preferable. They cut the wave better and allow you to stand on your feet when you throw. PVC boats with a flat bottom on such water can be dangerous because of the risk of tipping over when large fish jump.
The Hidden Benefits of RIBs
Hard bottom and inflatable cylinder (RIB) boats combine the stability of the catamaran with the softness of the inflatable boards. They are ideal for sea spinning fishing, but require a trailer to transport.
For small rivers and overgrown lakes, where the ability to drag through reeds and shallow waters is important, the classic flat-bottomed inflatable boat is out of competition. It is lighter, more maneuverable and easier to maintain, although it is inferior in comfort on the current.
Tuning and refinement for spinning
Buying a naked boat is just the beginning of the journey, and turning it into an effective tool for a spinner requires a lot of refinement. transom-wheelThis device allows one person to easily move a motorboat over solid ground, which is critical when descenting frequently.
Next, you need to think about the gear attachment system, and the spinning driver needs to have quick access to 3-4 rods, without getting up and without risking dropping them into the water, and they use special holders that attach to the liner cable or sides, and it is important that they have an angle adjustment and a reliable lock.
- 🛠 Installation of a runduk for storing personal belongings and spare baits.
- 🛠 Installation of the platform under the sonar with the possibility of quick removal.
- 🛠 Organization of an anchor system with the possibility of dropping the anchor from the nose or stern.
☑️ Checklist of basic tuning
And comfort is also a good thing. A seat on a can quickly tires your back, and replacing regular seats with soft seats with a high backrest and adjustable seating can significantly increase your comfortable fishing time, and some models allow you to place your seats on a guideline, changing their position depending on the fishing conditions.
Equipment with navigation and electronics
Modern spinning is not possible without a sonar and GPS, and these devices allow you not only to find fish, but also to return to the verified points (waypoints), which is especially important when fishing for jigs or wobblears at great depths. The anchoring of the sonar sensor should be reliable, but allow you to quickly remove it if necessary.
Inflatable boats often use airtight boxes to power electronics, which hold the battery, which protects the battery from splashes and ensures safety, and it is better to run the wiring inside special channels or lock it with clamps so that it does not get confused under the feet.
| Type of device | Place of installation | Features of installation |
|---|---|---|
| Echo sounder (sensor) | On the transom or bottom | A smooth patch of water without bubbles is required |
| GPS antenna | On the nose or the counter | Open view of the sky, away from metal |
| Battery | In a germ box at the bottom | Reliable fixation, protection from moisture |
| Display. | On the bracket before the fisherman | Angle of view, protection against glare |
⚠️ Warning: When installing electronics, be sure to use fuses in the power chain. Short circuit in a wet boat can lead to fire or failure of expensive equipment.
Anchor system and methods of anchoring
For a spinning man, an anchor is not just a load, but a boat-control tool. Unlike trolling, where a cat anchor simply holds a vessel, spinning often requires you to stand "stretched" or position accurately above the brow. The classic cat anchor is good for a hooked bottom, but holds poorly on sand or silt.
The best solution is the Danforth anchor, or its analogues, which have legs and are buried in the ground. Inflatable boats, the weight of the anchor is important: it must be sufficient to hold, but not excessive, so as not to overload the transom. The length of the anchor tile should be triple the depth at the fishing site.
Use a foam buoy on the phaloid, which will allow you to easily find anchor when sampling and not pull a dirty cable with your hands, and also save the boat if you have to sharply break the anchor from the hook.
The fast anchoring system from the bow of the boat (anchor trolley) has a huge advantage: it allows you to change the angle of drift of the boat relative to the wind and current, without getting off the anchor. It is an indispensable thing for catching steep dumps when you need to slowly walk along the brow.
Safety and equipment on the water
Spinning fishing is often associated with active movements, so the safety requirements are higher here. Having a life jacket is a must, even if you are a great swimmer. The vest should be comfortable, not constraining your hands when throwing and have pockets for trifles.
Shoes also play an important role, and the sole must be non-slip, as the deck of a boat is often wet and slippery, and regular sneakers can cause a fall overboard, especially when catching large fish.
- 🛡 Mandatory availability of a first aid kit and means of communication (phone in a sealed case).
- 🛡 Check the pressure in the cylinders before each fishing.
- 🛡 The presence of a remix and pump in an easily accessible place.
⚠️ Warning: Never leave the boat in the sun completely pumped unattended. The air pressure rises when heated, which can cause the seams or valves to rupture.
Seasonal features of operation
The boats have their own specifications in different seasons, and in summer, the main problem is overheating and the risk of puncture on sharp sand or shells, during which time it is important to check the pressure often and avoid dragging the boat on a hard shore without protection.
Autumn fishing requires protection from cold and wind. Inflatable sides in cold water take away body heat, so you should use special mats or inflatable mattresses to insulate yourself from the cold floor of the boat. Also in autumn, storm warnings become more frequent, and the launch should be strictly justified by weather conditions.
Properly prepared and equipped boat expands the capabilities of the spinner, allowing you to catch inaccessible areas from the shore and catch in any weather.
Winter storage requires careful washing and drying, and mud and silt can be preserved in the cloth, causing it to break down by next season, and fold the boat freely without dragging the bag straps so that the folds do not form microcracks.
Frequently Asked Questions (FAQ)
How long should a boat be for a spinning player?
The optimal length for single fishing is 320-340 cm The shorter length (270-290 cm) will be unstable and cramped for equipment, and more than 360 cm will already be difficult to transport to one person without a trailer.
Can I use a boat with an inflatable floor for spinning?
You can use it, but it's very inconvenient. Air Deck doesn't provide a rigid platform, it's hard to stand on, and when you're wiring the jig, you can't balance it, it's only for cruising or very calm water.
Do I need a keel for a spinning boat?
The inflatable keel greatly improves the course stability and controllability, especially in wave and side winds, and for large bodies of water, its presence is desirable, although on small rivers you can do with a flat bottom for better maneuverability.
How to properly store the boat in assembled form?
Keeping a fully assembled boat is not recommended due to the space and risk of damage, but it is better to blow it away, wash it, dry it and put it in a bag in a dry room at plus temperature, avoiding direct sunlight.