Choosing a swimming aid for fishing or resting on the water often turns into a complex process of comparing dozens of models. Hunter Boat 320 It occupies a special place in this row, being one of the most popular solutions in the budget segment of inflatable vessels, its dimensions are ideal for operation on medium and large reservoirs, where wave resistance and the ability to install a full outboard motor are required.
Many users are looking for information about the bundle of the Hunter 320 boat with the engine, since it is in this tandem that the full potential of this model is revealed. PVC materialsThe silk-powered silk-powered engines used in manufacturing provide light weight, and the transom design allows for engines up to 9.9 horsepower, making the kit mobile and efficient. In this article, we will take a look at everything from specifications to practical assembly tips.
Design features of the body and bottom
The basis of reliability Hunter 320 It's the geometry and the quality of the materials. five-layeredIt's resistant to gasoline, oils and ultraviolet radiation, and the bottom of the boat is made with technology. AirDeck (high pressure inflatable floor), which provides excellent rigidity and hydrodynamics when entering the planing.
It is important to note the presence of powerful inflatable tubes, which give the vessel additional buoyancy and safety. The width of the case for cylinders is 142 cmThe shape of the bow is designed to effectively break the wave, minimizing impacts on water, and provides high stability even when fishermen move abruptly inside the cockpit.
⚠️ Warning: Despite the high strength of the material, avoid contact of the inflated bottom with sharp stones or shells on the shore. Always use a protective mat or special descent clothing to prevent mechanical damage to the valves or seams.
The transom board is built directly into the inflatable tubes and protected by a layer of durable plastic, and this solution allows you to withstand vibrational loads from work. boat-engine The transom rigidity is sufficient to fit electric motors or petrol units up to 10 hp.
Technical specifications and weight parameters
When choosing a boat, it is critically important to understand its real dimensions and carrying capacity. Hunter 320 It is designed as a versatile boat for 2-3 people, but its performance depends on the correct loading.
Below is a table with basic technical data to help you match the boat's capabilities to your needs:
| Parameter | Meaning | Note |
|---|---|---|
| Full length | 320 cm | Dimension assembled |
| Full width | 142 cm | Maximum cylinder width |
| Load capacity | 400 kg | Including boat and motor weight |
| Engine power | up to 9.9 hp | Recommended traction |
| Boat weight | ~34 kg | No attachments. |
The total weight of 34 kg makes the boat quite transportable on a passenger car, but carrying it disassembled alone can be difficult, especially when you consider the weight of the engine and battery. Weight distribution The cockpit must be uniform to reach maximum speed.
The capacious cockpit allows two fishing boxes, a sonar and a fuel reserve, while leaving enough room for comfortable paddle-racing in the event of motor failure. The oars that come with the kit have aluminum alloy and comfortable handles, but for frequent rowing, they are better replaced with lighter carbon fiber counterparts.
Motor group selection for Hunter 320
The question of which engine to choose is key for owners of this model. Hunter 320 It works most effectively with two-stroke engines with a capacity of 5 to 9.9 hp Installation of a lower power motor will not allow you to get on plane with two passengers, and excessive power can be dangerous.
The optimal option is a 9.9 hp engine with the possibility of software or physical flashing (strangulation) up to 15 hp, if the transom design and your skills allow it. 9.9 horsepower.
When installing the motor, it is important to correctly choose the height of the transom. PVC boat characterized by a small deflection of the transom board under load, so the motor is often put slightly higher than on a rigid body, or use battery stands to balance the trim.
Use an anti-cavitation stove on the engine's lower unit, which should run parallel to the bottom of the boat when it goes into planing, which will significantly improve driving performance and reduce fuel consumption.
Installation and attachments
Standard equipment Hunter 320 It usually includes the boat itself, the bag, the refit, the pump and the paddles, but to fully operate with the engine, you will need to buy a number of important accessories, without which you can not navigate safely and comfortably.
First of all, you need to purchase an anchor system. For a boat 3.2 meters long and 1.42 meters wide, the optimal anchor weighing 3-4 kg of the type "cat" or "Grappling" should be buoyant and have a length of at least two depths of the reservoir.
- 🎣 String transneur - necessary for reliable fixation of the engine, often comes with a set, but requires verification.
- 💺 Siedenia - Staff shops are tough, for long fishing it is better to buy soft inflatable seats with mounting in lyctross.
- 🛡️ Protective apron - protects cylinders from sparks from the exhaust pipe of the engine.
Also worth considering is buying a quality anchor dip, which may not be strong enough for frequent use, and adding an extra dip to your nose will make it easier to anchor from your nose, which is especially important when fishing in windy weather.
Assembly and preparation for launching
Assembly process Hunter 320 It doesn't require any special skills, but following a sequence of actions will prolong the life of the product. In the cold season, the boat should be brought into a warm room a few hours before assembly, so that the material becomes elastic.
☑️ Checklist for descent preparation
The pumping should be done in stages. First, the cylinders are filled to a pressure of 0.2 atmosphere, after which the boat is allowed to "rest"; this allows the internal partitions and seams to be straightened out. Then the pressure is brought to a working value of 0.25-0.3 atmosphere. It is strongly recommended not to exceed the pressure of 0.35 atm, especially in hot weather.
⚠️ Warning: Never leave a fully pumped boat in direct sunlight for long periods of time unattended. Thermal expansion of air can cause joints to rupture or deform valves. In heat, put excessive pressure.
The slingboard and seats are installed after the main pumping of the cylinders. It is important to ensure that the mounts do not clamping the material of the cylinders. The motor is attached last, before descending into the water, so as not to weight the carrier.
Operation and behaviour on the water
On the water. Hunter 320 It's a very predictable, very stable, very well-rounded boat, and it's very fast, very fast, very fast, very fast, very fast, very fast, very fast, very fast, very fast, very fast, very fast.
When fully loaded (two people plus gear), weight redistribution may be required to get on plane: passengers should shift closer to the nose or to the center, depending on the excitement. AirDeck It provides good stiffness, but on a large wave may feel some "wagging".
Gleaming secrets
For a better planing under full load experience, try lifting the boat's nose, moving cargo or passengers into the stern at the start, and then returning to the seats after the plane mode, and using transom plates or imitating them by placing bars under the front of the engine (with caution!) also helps.
High speed control depends on the position of the engine's lower unit, and proper adjustment of the different reduces water resistance. Speed. boats with one driver can reach 25-28 km / h, with two passengers - about 20-22 km / h.
Care, storage and winter conservation
Durability PVC boats After every trip to the water, especially the salt water, the boat needs to be washed with fresh water, which will wash away the residues of salt, sand and organics that can destroy material and accessories.
Drying is a mandatory step before packaging, and even a small amount of moisture inside the bag can cause mold and unpleasant odor, as well as oxidation of the valves, and dry the boat in the shade, in the straightened form.
- 🧼 Wash the boat with a soft sponge using specialized PVC products.
- 🌡️ Store the product at a temperature of -20 to +40 degrees Celsius in a dry room.
- 🔧 Regularly check the tightening of the fasteners of the fittings and the condition of the seams.
For winter storage, it is better to leave the boat slightly lower to compensate for temperature changes, it is optimal to store it in an unswerving form or in a freely rolled-up state, avoiding the formation of sharp cavities on the materials.
Proper drying and storage in its pure form is a guarantee that the Hunter 320 boat will last you more than 10 years without losing its tightness and strength.
Frequently Asked Questions (FAQ)
Can I install a 320 engine with a 15 hp on Hunter?
Technically, the transom will withstand a short-term load, but the manufacturer officially recommends engines up to 9.9 hp Installation of a more powerful motor (for example, 15 hp by removing the limiter from 9.9) is possible by experienced users at their own risk, but this can reduce the safety and stability of the boat, and also cancels the warranty.
What is the actual build time of Hunter 320?
With experience and an electric pump, it takes about 10-15 minutes to assemble, the first time or when using a foot pump, it can take 25-30 minutes, and it's important to take your time and monitor the pressure in the cylinders.
Does the boat fit in the trunk of the sedan?
The bag packs are approximately 115x45x40 cm In most sedans of the middle class (C-Class and above) bag fits if you fold the rear seats. In small cars (A and B class) boat may not enter due to the size of the bag.
Do I need to lubricate the valve before pumping?
No special lubrication is required, but you need to keep the valve clean. Sand or dirt trapped in the thread or locking mechanism can lead to etching air. Before screwing the valve, make sure it is clean.