Choosing a boat for fishing and recreation on the water is always a search for a compromise between cost, durability and comfort. In the Russian climate and often unpredictable weather events, many water engines turn their attention to domestic products, in particular, to the products of the domestic manufacturer. LASH (Leningrad Aluminum boats) Model LAS 2 It is deservedly considered one of the most popular in its class, offering excellent seaworthiness and capacity.
This boat is a welded structure, which distinguishes it from many of its counterparts assembled on rivets. It is the monolithic hull that ensures high reliability and safety when going out into the open water, whether it is Lake Ladoga or the wide river expanses of the Volga. Many owners note that it was the lack of riveted joints that was the decisive factor in the purchase.
But despite the obvious advantages, this model has its own nuances that must be considered during the planning stage of the purchase, the proper preparation for operation and understanding of the technical limitations will allow you to enjoy water trips for many years without unnecessary headaches.
Design features and geometry of the body
The basis of reliability LAS 2 The AMG5M aluminum alloy used in manufacturing is highly corrosion-resistant and tough, which is critical for aggressive aquatic environments. Unlike many competitors, you won't find current seams here even after several seasons of active use.
The bottom geometry is designed to plane with confidence even at average engine power, and the keel-width angle of the transom allows you to effectively cut the wave, providing a soft ride and reducing the impact on the body and passengers, and this is especially true in the wind, when there is a ripple or short wave on the water.
⚠️ Attention: Despite the high strength of welds, avoid touching underwater obstacles at high speed. Aluminum is a plastic material, but a strong impact on a stone or log can deform the skin, disrupting hydrodynamics.
An important element of the design is a reinforced transom, which is able to withstand significant loads from outboard motors, and the design of the side includes a hinge beam that protects the side during mooring and mooring. A workhorse ready for serious workloads.
Technical specifications and load capacity
For many potential buyers, the ratio of dimensions and payload becomes a decisive factor. LAS boat 2 It has an impressive size that allows you to comfortably accommodate several people and the necessary equipment, standard length is 4.8 meters, and the width on the midsection reaches 1.95 meters, which provides excellent stability.
The load capacity of this model allows you to take on board up to five people, although the optimal is to accommodate three adult fishermen with a full set of equipment. The engine set can vary widely, but the most rational choice is considered the “golden mean” in power.
Let’s look at the main parameters in more detail in the table below:
| Parameter | Meaning | Note |
|---|---|---|
| Longest length | 4.80m | Excluding the attachments |
| largest width | 1.95 m | By zygomatic bend |
| Height of board | 0.80m | Midle. |
| Hull mass | ~190 kg | No motor or equipment. |
| Load capacity | 600 kg | Including passengers and equipment |
It is worth noting that the actual weight of the vessel may vary slightly depending on the year of production and configuration. Passenger capacity The vessel is designed to be buoyant, making it safe even if a small amount of water gets inside.
Performance in water
Conduct LAS 2 on the water depends on the installed power plant and load distribution. When going to planing with a 30-40 hp engine, the boat demonstrates a confident set of speed and good course stability. However, for a comfortable ride with two or three loads, it is recommended to consider engines with a capacity of 50 hp and above.
The seaworthiness of the vessel allows you to go out on the water at a wave of up to 1 meter, which is an excellent indicator for an aluminum boat of this size. The high side protects against splashes, and the keeled shape of the bottom softens the shocks against the wave. However, in strong lateral winds, the sailing of the high side can affect handling.
To improve handling at high speeds and in windy weather, it is recommended to use transom plates or hydrofoil on the lower unit engine.
So, sound insulation is an important aspect, and the aluminum body is very good at sound, so the engine noise and the water splashing will be very good, and many owners solve this problem by putting an extra layer of vibration and noise insulation on the bottom and on the side, which also has a positive effect on thermal insulation in cool weather.
Choice of engine and attachment equipment
Motor selection for LAS 2 is a task that requires a balanced approach. The manufacturer allows the installation of engines with a capacity of up to 60 hp, but practice shows that the most economical and effective option is the motors in the range of 30-50 hp Two-stroke models will provide better acceleration dynamics, and four-stroke will please silence and economy.
When choosing a motor, you should also consider its weight, and installing a too heavy engine on a transom can lead to overloading the stern and reduced driving performance, and many consider Japanese or American brands that have proven to be reliable in our latitudes to be the best solution.
⚠️ Warning: When installing a motor with a power of more than 40 hp, be sure to check the condition of the transom plates and reinforcing scarves. Excessive vibration of a powerful motor can weaken the welded joints over time if the transom design has not been strengthened.
Besides the motor, the anchor is an important element. For a boat of this size, an anchor weighing at least 5-6 kg, preferably a cat or admiralty type, is required to reliably keep the vessel on the current or in the wind.
boat transport and storage
Transportation The LAS 2 is in front of the owner immediately after purchase, the hull weighing about 190 kg makes it impossible to launch a single person without the use of special equipment or a gentle concrete slip.
When stored in the off-season, the aluminum case does not require such thorough conditions as fiberglass or PVC. However, it is recommended to keep the boat upside down under the canopy to prevent precipitation and debris from entering. This will also prevent condensation on the interior surfaces.
☑️ Preparation for winter storage
If you plan to keep the boat on water all season, you need to check the status of the fouling of the bottom regularly and clean it if necessary. Although aluminum absorbs less than some other materials, in standing water this process can go quite quickly, reducing speed specifications.
Maintenance and extension of service life
Aluminum alloys of the AMG series are resistant to corrosion, but that doesn't mean the boat doesn't require maintenance at all. LAS 2 This is electrochemical corrosion that can occur when in contact with other metals in salt water or when wandering currents on metal berths.
Regular inspection of the body for chipped paint and scratches will eliminate the oxidation foci in time. Even small damage to the protective coating is better immediately painted with a special primer and paint for aluminum to prevent the development of deep corrosion.
To wash the case, use only soft sponges and special products that do not contain abrasive particles and aggressive alkalis. The use of metal brushes is strictly prohibited, as they leave microparticles of steel, which will subsequently rust and spoil the appearance of the board.
The Secrets of Aluminum Pollining
To return the shine to the tarnished aluminum, you can use specialized polishes with chromium oxide. However, you should not overdo it, since each time you remove the micron layer of metal.
Comparison with competitors and final conclusions
In the aluminum boat market at LAS 2 There are serious competitors, such as Crimea or different models from Master. and saluteHowever, it is the combination of price, welding quality and time-tested design that makes this model the leader in sales in its segment. LASH It's from riveted boats, tired of the constant leakage of seams.
Compared to the inflatable analogues, LAS 2 It's a choice for those with storage space and trailer transport, and for overnight fishing or long hikes, it's one of the best entry-level options.
The LAS 2 boat is an investment in safety and durability that, if properly maintained, will last for decades, even by inheritance.
So to sum up, this boat is a very popular boat, simple as a hammer, and reliable as a Kalashnikov, and if you're looking for a universal boat for fishing, hunting and family water recreation, and you're willing to put up with the need for a trailer, you can't afford to have a trailer. LAS 2 It's a great choice.
Do I need to register the LAS 2 boat in GIMS?
Yes, the boat must be registered if the power of the installed engine exceeds 8 kW (approximately 10.8 hp) or if the weight of the curb vessel exceeds 200 kg. Since the weight of the LAS 2 is about 190 kg, the addition of the engine, fuel and equipment is almost guaranteed to take you beyond the limit of 200 kg, which makes registration mandatory.
What is the maximum weight of the motor that the transom can withstand?
transom LAS 2 is designed to fit motors up to 60 hp The weight of such a motor (about 100-110 kg for a four-stroke) is the limit. When installing more powerful or heavy motors, it is recommended to consult with the manufacturer or strengthen the transom with additional elements.
Can I make a crack in the body by myself?
Theoretically, you can use argon welding and filler material of the same brand (AMg5). However, professional equipment and welder skills are required for quality repairs. Incorrect cooking can lead to overheating and weakening of adjacent areas, so critical damage is better trusted to specialized workshops.
What is the real speed of a boat with a 40 hp engine?
With a 40 hp engine and one operator on board, the LAS 2 boat is able to reach speeds of up to 35-40 km / h. With a full load (3-4 people), the speed will decrease to 25-30 km / h, which is quite a comfortable mode for moving around the water area.
Does LAS have 2 modifications?
Yes, there are various modifications and versions, for example, LAS-2M or crumbling versions, and often there are boats with already installed equipment from previous owners. When buying a used copy, it is important to check the compliance of the actual configuration of the declared model in the documents.