Choosing a reliable fishing boat or a family holiday on the water always involves a compromise between cost, weight and functionality. In the small metal vessel segment, models designed to meet Russian operational realities occupy a special place. Mishimo 335 Light It was a boat that became popular thanks to the combination of lightweight aluminum hull and sophisticated ergonomics, and unlike the classic "Kazank" or "Oba" models, this project was created with an emphasis on minimizing weight without critical loss of strength.
Owners who encounter this vessel for the first time are often surprised at how easily it can be transported even on the roof of a passenger car. The aluminum-magnesium alloy used in manufacturing provides excellent corrosion resistance, which is critical for bodies of salty or contaminated water. However, to fully unlock the potential of this model, you need to understand its design features and limitations.
Further analysis will allow you to understand whether it is suitable for you. Mishimo 335 Light We'll look at the nuances of the assembly, the specifications of the running, and the specific requirements of the outboard motor, and understanding these aspects will help avoid the typical mistakes in buying and operating a small vessel.
Design features of the body and materials
The basis of durability of any small vessel is the material of its manufacture. Mishimo 335 Light It is made of the AMG5M alloy, which has a high tensile strength and excellent weldability. The thickness of the bottom and sides varies depending on the load zone, which allows you to optimize weight specifications. In the most loaded places, such as the cheekbones and transoms, a sheet of greater thickness is used to resist impacts on water and logs.
The hull is designed with a flat bottom and pronounced zygomatic bends, and this geometry provides parking stability, which is especially appreciated by anglers-barrels, while the flat bottom requires careful wave control, since the shocks against the wave can be severe. The radius of rounding of the cheekbones of the model 335 Light is selected specifically to reduce splash formation at low speeds.This is different from the faster versions with a deep V.
⚠️ Warning: Aluminum-magnesium alloys are sensitive to electrochemical corrosion when in contact with other metals in salt water. Do not install steel brackets on the transom without insulation pads.
The hull is assembled by argon-arc welding, which ensures that the seams are tight without the use of sealants, which can eventually dry out. The quality of the seams is a key factor in durability. When inspecting a new boat, you should pay attention to the uniformity of the seam roller and the lack of porosity. Uneven heating during welding can lead to microcracks in the future, especially in stress areas.
Technical specifications and load capacity
Understanding the numbers stated by the manufacturer is necessary for the correct selection of equipment and the evaluation of operational safety. 335 light It is positioned as a two- or three-seat vessel, but the actual payload depends on many factors, including wave height and weight distribution.
An important parameter is the power of the recommended outboard motor. For this modification, the optimal range is considered to be engines with a capacity of 2 to 5 hp Installation of a more powerful motor is possible, but requires caution and can lead to a violation of the centering and reduced safety. The maximum speed with a 5 hp engine is about 15-18 km / h, which is enough to move on calm water bodies.
Below is a summary table of the main technical parameters that will help compare the model with competitors:
| Parameter | Meaning |
|---|---|
| Full length, mm | 3350 |
| Full width, mm | 1350 |
| Height of the side, mm | 380 |
| Load capacity, kg | 200 |
| Body weight, kg | 35 |
It is worth noting that the actual weight of the kit may differ from the passport due to the variability in the thickness of the metal in different lots, also the weight is affected by the presence of additional elements, such as shingles or reinforced clamps. When calculating transportation on the roof of the car, consider that the weight of the boat will be added to the weight of the engine, fuel and equipment.
Ergonomics and interior equipment
Interior space Mishimo 335 Light The boat floor is usually reinforced with transom banks that serve as seats for passengers, and the cans are designed to be dismantled when needed, making room for large cargo, such as catch or tourist equipment, and fastened so as to exclude backlash during movement.
The nose often has a platform for anchoring or tackle, although it can be minimalist in basic configuration, and many owners customize this knot by installing bollards or dice for reliable fixation. Onboard elements are made with a bend inwards, which increases the rigidity of the structure, but may interfere with the installation of certain types of linings or onboard protections.
- 🛶 transom plate: reinforced and designed for the engine attachment, has protection from flooding waves.
- 🪑 Banks: Removable, made of the same aluminum sheet steel, have an anti-slip coating or notch.
- ⚓ Forpic: The space in the nose can be used to store things, covering them with an awning or a lid.
☑️ Check before buying a used boat
Special attention should be paid to the drainage system. In the basic version, the drain hole may be absent or be made as a simple stopper. For comfortable operation, it is recommended to immediately install a quality drain valve that will prevent backflow of water when driving, this is especially true when fishing, when water from fish and gear constantly enters the boat.
Operation on water: driving performance
Conduct Mishimo 335 Light In quiet water, lakes and small rivers, the boat shows itself as a stable platform; flat bottom allows you to easily jump into the boat from a flat bank and pass shallow areas where cider boats could get stuck. However, going out into open water in winds above 3-4 points requires experience and caution.
When driving with an engine, the boat tends to yaw if the engine is not centered correctly, and owners often have to experiment with the tilt angle of the lower unit and the position of the engine in height to find a balance between course stability and speed. planing This one-man 5-hp model is possible, but it will be unstable and dangerous at the slightest wave.
⚠️ Warning: Going out on a flat-bottomed boat with one person on board is prohibited by safety regulations due to the high risk of tipping over.
To improve driving performance, many enthusiasts install transoms or hydrofoils on the engine, which allows you to raise your nose a little and reduce water resistance. However, it is worth remembering that any modification changes the weight. Before installing additional equipment, you should consult with specialists or experienced boaters.
Transport and storage
One of the main advantages of the model 335 light The hull weighs only about 35 kg, which allows one person to easily move the boat to the water or load it onto the trunk of a car. No special permit is required to carry a car on the roof, because the dimensions do not exceed the permitted limits, but the mounting must be reliable, using dynamic belts.
Storing a boat is also easy, and you can hang it in a garage, shed, or even on a balcony (length permits), and aluminum is not afraid of extreme temperatures and humidity, so it's safe to leave it under a canopy in the summer cottage, and the only thing you should do before long-term storage is to turn the boat upside down so that there's no moisture or debris inside.
- 🚗 On the roof: requires the presence of strong crosses and reliable nodes attaching the nose and stern to the body.
- 🏠 In the garage: Suspended storage on brackets is ideal, saving space on the floor.
- 🌲 Outside: Storage is permissible under an awning, but it is better to avoid direct contact with the ground using stands.
When transporting long distances on the highway, it is important to consider sailing. An empty boat on the roof creates significant aerodynamic drag, which increases the fuel consumption of the car. In addition, in lateral winds, driving the car can become difficult. Always slow down when there are strong winds.
Comparison with analogues and final conclusions
There are many analogues on the market, such as Kazanka-M, Ob-2 or various Chinese models. Mishimo 335 Light Compared to the Kazanok, the metal version is more resistant to puncture and does not require complex painting care (if unpainted aluminum is used).
Choosing between a new budget metal boat and a used model of a well-known brand, many are inclined in favor of the new model. Mishimo It's a workhorse for a fisherman who values simplicity and reliability, and it's not designed for high-speed walks, but it does a great job of getting the fisherman to the point and back.
So in conclusion, this model is worth considering as a newcomer or as a second boat for an experienced water-engineer, and its simplicity minimizes the number of units that can fail, and when operated carefully and safely, it's not a problem. Mishimo 335 Light It will last for many years, maintaining its driving qualities.
Do I need to register Mishimo 335 Lights in GIMS?
Registration is required if the weight of the curbed vessel (hull + engine) exceeds 200 kg or if the engine power is more than 8 hp (8 kW). Since the hull weighs about 35 kg, you can use the engine up to 5-6 hp and do not register the boat unless the total weight exceeds the limit. However, the rules may change, always check the current legislation.
Can I paint an aluminum boat Mishimo?
Yes, but it requires special training. The usual paint will not fall on aluminum and quickly peel off. You need to use special soils for non-ferrous metals (for example, on an epoxy basis) and polyurethane enamel. Often owners simply polish the metal or use protective compounds such as "liquid aluminum".
Which anchor is best used for this boat?
For flat-bottomed boats with a length of 3.35 meters, the optimal anchor of the type "cat" weighing 3-4 kg or an anchor of Hall / Sailor weighing about 2-3 kg. The main thing is the presence of a sufficient number of anchor lines (at least 15-20 meters) and a reliable mounting of the tile on the nose so that when snatching, the boat does not turn side to the wave.