The modern market of small craft is full of offers, but the model of the boat is not. Norvik 320 It's a well-deserved low-cost boat that's designed for those who are looking for a balance between affordable cost and the reliability they need to get on the water, and many water-engineers choose this length because it's universal for one or two people.
The design of the product is based on the use of high-strength materials, which allows you to withstand serious loads even in choppy conditions. Tissue density Here, it plays a crucial role, ensuring tightness and resistance to mechanical damage against stones or driftwood, and the owner receives a full-fledged fishing or recreational tool that does not require complex maintenance.
It is worth noting that in this model, reinforced PVC with a density of 850 g / sq.m.This safety margin allows you to operate a boat not only on calm lakes, but also on rivers with moderate currents. The right approach to choosing equipment turns this "inflator" into a serious combat boat.
Design features and materials
The basis of durability of any inflatable vessel is the quality of the polyvinyl chloride used. Norvik 320 The manufacturer did not compromise by using a five-layer reinforced material, which provides excellent resistance to ultraviolet, fuel and temperature changes, which is critical for operation in Russian latitudes.
The seams are made according to the technology of gluing on the floor using two-component glue. Tightness These compounds are tested in the factory, minimizing the risk of leakage in the field, but it is worth noting that any adhesive requires careful treatment and periodic inspection, especially after winter storage.
⚠️ Warning: Never keep a assembled boat under direct sunlight during the summer, and the air pressure inside the cylinders may exceed the permissible limits, leading to seam strain or tissue rupture.
The bottom of the boat deserves special attention, as it takes the main load when landing, uses an inflatable keelson, which gives the bottom rigidity and hydrodynamic properties, which makes it easier to go to the planing when installing the engine, saving fuel and engine life.
Secrets of longevity of seams
Manufacturers often use polyurethane glue, which remains elastic even in severe frosts. However, if you plan to operate a boat at temperatures below -20 °C, let it warm up in a warm room before pumping to avoid microcracks on the cloth folds.
Technical specifications and dimensions
The dimensions of the model make it easy to transport in the trunk of a passenger car in disassembled form. The weight of the kit remains within reasonable limits, which is important for single fishermen who have to carry equipment on foot to the water. Accurate figures will help you plan your purchase and understand whether this vessel will fit your tasks.
The internal volume of the cockpit is designed to accommodate two adults with a stock of equipment. Load capacity declared by the manufacturer with a good stock, but in practice it is better not to load the boat to the limit to maintain a high landing and stability.
| Parameter | Meaning | Unit of measurement |
|---|---|---|
| Total length | 320 | centimeter |
| general width | 140 | centimeter |
| Diameter of the cylinder | 36 | centimeter |
| Load capacity | 350 | kilogram |
| Weight of kit | 32 | kilogram |
It is important to consider that the actual weight may vary slightly depending on the configuration and year of release. transom hanging It allows motors up to 5-8 hp, which is optimal for a given length, and overpowering can lead to transomper failure or loss of handling.
Component and ease of assembly
Buying. Norvik 320You get a complete set of things to start with, and the standard package is usually the boat itself, the removable seats (banks), the pump, the remix and the bag for transportation, and having all the components out of the box eliminates the need to buy the little things separately.
The assembly and disassembly process is worked out to the smallest detail and takes about 15-20 minutes for an experienced user. Valves. They have a reliable design that excludes spontaneous air infusion, but requires careful closing. It is recommended to use a pressure gauge on the pump so as not to pump the cylinders.
- 🎒 The backpack bag is made of durable fabric and has convenient webbing for carrying.
- 🪑 Seats (banks) are easily installed in any position along the length of the cockpit thanks to the mounting system.
- 🔧 The remake contains patches and glue sufficient to eliminate small punctures in the field.
The can mounting system is particularly noteworthy, allowing you to change the position of the cans, making room for a large cargo or providing a comfortable fit for two, making the boat versatile for different use cases, from fishing to cruising with the dog.
☑️ Checking before getting on the water
Water operation and driving performance
On the water. Norvik 320 The wide cylinders provide good stability, allowing fishermen to make sudden movements or get up to throw gear without the risk of overturning. Kieliness The bottom helps break a small wave, making the move softer.
When you install the engine, the boat easily enters the planing mode with one passenger. However, it is worth remembering that the inflatable floor (BND) or sleigh has its own speed and load limits. Sharp turns at high speed can lead to shifting of the center of gravity and tipping.
⚠️ Attention: When driving against the current or in strong side winds, always keep the course at an angle. The drag on inflatable boats is higher than on hard-hull boats, which requires more engine power.
The boat’s handling depends on the correct distribution of cargo. Centrification It should be such that the nose is slightly raised, and if the nose is buried in water, it not only reduces speed, but also increases the risk of being swept overboard by a wave.
To improve driving performance and protect the bottom from abrasion on sand or stones, it is recommended to use a special protective tape (keel protector) or a motor mat.
Care, maintenance and storage
Long service life Norvik 320 It depends on how you care for it, and after every fishing, you should wash the salt, sand and silt with fresh water, and pay special attention to the valves and gluing places where dirt can interfere with the tightness of the connection.
Drying before packaging is a must, and even minimal moisture inside the bag during long-term storage can lead to mold and an unpleasant odor that is difficult to remove. PVC fabric It does not rot, but contamination can be a catalyst for the destruction of the material structure.
- 💧 Dry the boat carefully in the shade before packing, avoiding direct sunlight.
- 🧼 Use mild detergents, avoiding aggressive chemicals and solvents.
- ❄️ Store the product in a warm room at temperatures above 0 degrees Celsius.
Periodically check the pressure in the cylinders, especially if the boat was long in the assembled form. Loss of pressure can be a sign of a microscopic puncture or valve malfunction. Timely detection of the problem will save you from trouble on the water.
Proper storage in the off-season (in a dry, warm place, in a straightened or slightly deflated form) prolongs the life of PVC material by 5-7 years.
Opportunities of tuning and modernization
The basic equipment is good, but many owners are looking to improve their boats. Norvik 320 One of the most popular improvements is to install a reinforced transom if the regular one doesn't seem powerful enough for your engine.
They also often install additional straps (safety cables) around the perimeter of the cylinders, which allows you to hold them when you emerge from the water or attach additional equipment outside. tuning may include the installation of a sonar, fishing rod holders and hinged pockets.
Some fishermen replace standard cans with lighter aluminum or plywood cans with soft upholstery, which increases comfort during long transitions, and it is important to ensure that the weight of additional equipment does not exceed the permissible carrying capacity.
Should I buy a second-hand Norvik 320?
Buying a used boat can be justified by saving, but requires careful checks. Inflate the boat and leave it for a day: if the pressure has not fallen, then there are no punctures. Examine the seams for layers ("mustache") and check the condition of the tissue by touch - it should not be sticky or crumble.
What pressure to pump into cylinders?
The optimum working pressure is usually 0.2 atm (about 200 mbar or 3 psi). The exact values are always indicated on the manufacturer's plate or in the instructions. Pumping is dangerous by rupturing seams in the sun, under-pumping reduces the rigidity of the structure.
Is it possible to use a boat in winter?
You can use PVC boats in winter, but the material becomes tough and brittle in the cold, requires extremely careful transportation and assembly, and avoids contact with sharp edges of ice, as the risk of puncture increases many times over.