Finding a reliable boat for weekend fishing or family walks often leads to a model. Aqua 3200It is one of the most talked-about boats in the budget segment, attracting attention with its inflatable floor of the NDNDM. It is the ability to quickly go plane with minimal number of passengers that makes this size popular among motor anglers.
However, before placing an order, you need to weigh all the pros and cons. Unlike classic models with hard floorboard, NDND has its own features of operation, which can be a decisive factor. inflatable floor It provides a high level of comfort, but requires compliance with certain rules during assembly and storage.
In this article, we will discuss in detail the specifications, the real experience of operation and the hidden nuances that often keep vendors silent about, you will find out whether this is the right modification for you or you should consider alternatives, this analysis will help you make an informed decision about buying.
Design features of the model Aqua 3200
The basis of the design is a solid PVCThe size of the boat (3.2 meters long, 1.46 meters wide) balances the roominess with maneuverability. The 0.38-meter tall side ensures dryness in the cockpit even in small waves, which is critical for a fisherman who spends several hours on the water.
The main “chip” of this model is the presence of an inflatable floor NDMA (Low Pressure inflatable floor) Unlike hard floorboard, it uses a balloon structure with a cellular structure that inflates to a pressure of 0.25 to 0.3 atmosphere, which allows you to get a flat, hard surface that resembles plywood, but with the ability to roll the boat into a compact backpack.
⚠️ Attention: Despite the rigidity, the bottom of the NDND is sensitive to punctures with a sharp stone or snag in shallow water.
To strengthen the structure are used stringerAnd these are the ones that run along the side and hold the cylinders tightly, and this prevents the hull from deforming when it's moving at high speeds. keelIt improves the exchange rate stability and protects the bottom from impacts.
The design of the NDND provides comfort comparable to hard-deck boats, but requires a more careful attitude to the bottom when pulling ashore.
The advantages of inflatable floor over floorboard
Many beginners ask themselves, why should you choose NDND over classic plywood? The answer lies in weight and comfort. Building a hard-floorboard boat is a physically demanding process that requires stacking a lot of sheets and fixing them. Aqua 3200 This stage is minimized: it is enough to straighten the bottom and pump it.
In addition, the inflatable floor has excellent thermal insulation properties, and sitting on a cold plywood sheet in the early morning is a questionable pleasure, while the air layer of NDNDND retains heat, especially for autumn fishing or the spring season, when the water has not yet warmed up.
- 🚀 Assembly speed: The time of preparation for launching is reduced by 30-40% compared to the plyol models.
- 🎒 Transportability: The absence of heavy plywood sheets allows you to pack the boat in one compact case, which is easier to carry.
- 🛡️ Safety: When hitting the bottom, the boat with NDND absorbs, reducing the risk of injury to a passenger who fell from the seat.
But there's a flip side to the coin, and the inflated bottom has less hardness on the kink than thick plywood, and if you put two people over 90 kg each, you can see a slight deflection, although for the 320 model, it's not critical because of the small size.
Capacity and load capacity
rated carrying capacity of the boat is 400 kg, which formally allows you to accommodate three adults, however, for comfortable operation and exit to planing with a 5 hp engine, it is recommended to take on board no more than two people. Optimal loading For this model - one fisherman with a full set of equipment or two vacationers with a minimum load.
The useful area of the cockpit allows you to freely fit with fishing rods. thong-engine It's important to consider that the center of gravity is shifting backwards, and if you're planning to take a trophy fish, it's best to spread the weight evenly across the sides so that you don't break the differentiation.
| Parameter | Meaning | Comments |
|---|---|---|
| Full length | 320 cm | Optimal for 2 people |
| Full width | 146 cm | Landing/disembarkation stability |
| Load capacity | 400 kg | Including the weight of the motor and equipment |
| Boat weight | ~28 kg | Without motor and accessories |
For fishing alone, this size is the "middle ground": the boat is light enough to be carried to the water alone (using wheels or red tape), and wide enough to feel confident when throwing a spinning.
Performance and motorization
Boat. Aqua 3200 NDLD Designed for operation with outboard motors up to 5 hp When installing an engine of such power, the boat goes on plane with one person weighing up to 80-90 kg. The speed on the water can reach 20-25 km / h, which is quite enough to move between fishing points.
A more powerful engine (e.g. 9.9 hp) is possible, but not always justified, and the increase in power will require a heavier engine, which, when paired with passengers, may exceed the recommended load capacity.
An important element is sink-boardIn this model, it's reinforced and protected by pads, and when you install the motor, you have to watch the right angle of the lower unit tilt to avoid burying the boat's nose in the wave, and you have to adjust it with washers or hydraulic lifts, if you have one on the motor.
⚠️ Warning: Operating a motorized boat above 5 hp requires special attention to weight distribution. It is not recommended to bring a full crew (2+ people) with a powerful engine to planing.
This model is great for trolling, and the flat bottom of the NDNDM creates less drag than hard-floorboard keel boats, which saves fuel when driving at low speeds.
Fuel economy secrets
When moving on planing, try to keep the engine in the rpm range where vibration is minimal. For 5 hp, this is usually 80-90% of the maximum power. Half-gas driving often leads to fuel overruns due to the engine's inefficient operation.
Assembly, pumping and preparation for water
The process of assembling a boat with NDND is very different from the usual sleeve options, so there's no need to insert sleighs and fix them, the whole process is to lay out the cylinders, pump and install the attachments, which is especially valuable when there's a strong wind or it's raining.
It is important to control the pressure in the cylinders: a sun-pumped boat can burst, and a poorly pumped boat will lose driving performance. The pressure in the cylinders is usually 0.2 atm, in the keel - 0.25 atm, and in the bottom of the NDNDM - up to 0.3 atm.
- 🔧 Tools: You will only need a pump and possibly a key for tightening valves (usually included).
- 🌡️ Temperature: When assembled in the cold, use only special frost-resistant pumps, ordinary ones can crack.
- 🧼 Gone: After each fishing, be sure to wash the boat with fresh water, especially if you have been swimming in salt water or dirty pond.
Drying a boat is a must before packing, and if you put the wet product in a case, in a couple of weeks you run the risk of mold and an unpleasant smell that will be extremely difficult to remove, dry in the shade, avoiding direct sunlight, which can overheat PVC.
☑️ Checklist before packaging
Repairability and durability
Materials reinforced PVCThe Aqua 3200 is a very abrasive, but like any inflatable, the boat is at risk of puncture, and it takes 15 minutes to repair that damage, and it's always a glue and patch remake.
The seams of the boat are coated, which ensures high leakage. Over time, especially when used in the sun, the adhesive may require updating. This is a normal aging process of polyurethane adhesives.
To extend the life of the boat, it is recommended to use PVC protective sprays containing UV filters, which prevent fading of the material and the appearance of microcracks, and avoid contact of the boat with fuel (gasoline, oil), as they destroy the structure of polyvinyl chloride.
⚠️ Warning: Never use Moment or other household cyanacrylate-based adhesives to repair PVC. They make the material brittle and inelastic. Use only two-component polyurethane adhesives.
With proper care and storage in a dry room at a temperature of not lower than -10 ° C, the boat can last 7-10 years or more. The critical factor is storage: rolled up in a tight roll boat for years lies in the garage without loss of properties.
Keep the boat in a straightened or semi-folded state in the off-season to avoid the formation of clutters on the folds of PVC fabric.
Frequently Asked Questions (FAQ)
Can I install a sonar on the Aqua 3200 NDND boat?
Yes, it's possible to install a sonar, and it's mounted on a transom board or a special bracket that you can attach to the cylinder, and it's important to make sure that the wires don't rub against the side when you're moving.
How long does it take to build a boat alone?
It takes about 10 to 15 minutes for a power user to fully assemble and pump, and the first time it can take up to 30 minutes, which is much faster than assembling a flatbed boat of the same size.
Will the bottom of the NDND withstand the weight of two people 100 kg?
Technically, the boat will withstand this weight, but the driving performance will deteriorate, the bottom can bend, creating additional resistance to water, and for such a load, you should consider models from 3.5 meters in length.
Should the valves be lubricated?
You can't oil the valves with oil or fat, and that will cause the rubber seals to collapse, and if the valve is tight, you can clean it carefully from the sand or replace the sealing ring.