Choosing a reliable fishing boat or outdoor activities on the water is often a challenge, especially when the budget is tight and quality requirements remain high. PVC boat Anchor 320 NDND It is widely regarded as one of the leaders in the budget segment, offering a trade-off between price and functionality that is hard to ignore, and it is this model that often becomes the first serious purchase for newcomers to water tourism.
In this review, we will take a closer look at the design features, the real performance and the nuances of operation that are not talked about in stores. NDMA (low bottom inflatable) is a game changer, and whether to overpay for more expensive brands if there is an available alternative. Security The water comfort depends on the right choice, so the information below is of an applied nature.
Many users are looking for objective data to see if a particular model will survive a particular operating environment, whether it's a quiet lake or a middle river, and we've analyzed the technical parameters and the experience of the real owners so you can make an informed decision. A key feature of the model Anchor 320 lies in the combination of a reinforced balloon frame with a low pressure inflatable floor, which provides excellent germination on the wave.
Design features and materials
The basis of the durability of any inflatable boat is the material from which its hull is made. Anchor 320 It uses a five-layer PVC reinforced fabric that is highly resistant to mechanical damage and ultraviolet radiation, with a material density of 750 g/sq.m., which is the standard for boats of this class, providing a balance between strength and weight.
Particular attention should be paid to the system. NDMAThis is an inflatable floor with built-in longitudinal and transom power belts, which allows the boat to keep its shape under load without the use of rigid plywood floorboards, significantly reducing the weight when assembled. Toughness The bottom is achieved due to high internal pressure, turning the balloon into a full-fledged platform for movement.
⚠️ Attention: When pumping the bottom of the NDND, carefully monitor the pressure gauge. Pumping in hot weather can cause the power tapes inside the cylinder to rupture, since the air tends to expand in the sun.
The seams of the product are made by a tape method, which guarantees the tightness of the joints even during prolonged operation in an aggressive environment. Glued stitches They are less susceptible to stratification than simple gluing, but they require careful handling in assembly and storage. The quality of fittings, including valves and handles, also corresponds to the declared price segment, although some elements may require strengthening over time.
Technical nuances of PVC fabric
The PVC fabric is made up of a polyester base coated with layers of polyvinyl chloride, and the reinforcement mesh inside gives the material tensile strength, and the outer layers protect against water and sun.
Dimensions, weight and capacity
When choosing a boat, it is critically important to take into account not only its length in an inflated state, but also the dimensions in a packaged form. Anchor 320 The boat is 320 cm long and 142 cm wide, allowing two adult passengers to comfortably accommodate their cargo, and when folded, it can easily fit into the trunk of a passenger car, making it ideal for spontaneous trips to water bodies.
The weight of the kit is one of the main advantages of this model. Due to the absence of heavy aluminum or plywood floor, the total weight of the boat with hinged elements remains within reasonable limits, allowing it to be carried by one person over short distances. Load capacity It is 320 kg, which formally allows the accommodation of two people and the necessary equipment, but for comfortable fishing it is better to focus on smaller loads.
For clarity, compare the main parameters with the typical requirements for fishing:
| Parameter | The value of Anchor 320 | Optimal for fishing |
|---|---|---|
| Length | 320 cm | 300-360 cm |
| Width | 142 cm | >140 cm |
| Boat weight | ~26 kg | <30 kg |
| Load capacity | 320 kg | >250 kg |
It is worth noting that the actual usable area of the cockpit can be reduced by bloated cylinders, so the legroom and placement of boxes with tackles should be evaluated with a margin. ergonomics Planting directly affects fatigue during long transitions or long waits for cool.
Comfort and ergonomics on the water
The low-pressure inflatable floor creates a unique feeling of softness that cannot be obtained on boats with hard floorboard flooring, which is especially true when on the water for a long time when the legs and back are stiff. Anchor 320 In this regard, it demonstrates itself from the best side, cushioning the blows on a small wave.
But there is a downside to the coin: the inflated bottom is more sensitive to punctures and requires careful preparation of the descent site. Many owners use additional inflatable seats or homemade ones to improve comfort, as regular cans can be tough for hours of fishing. Sustainable on water is achieved due to wide feed and proper contours of cylinders.
The arrangement of the paddle switches and the carry handles is logical, making it easier to operate the boat alone. electric motor It's important to center the transom in the right way to avoid yawing at the course. The wind sailing in the model is average, but with strong side winds, it can be difficult to drive a boat without a keel or a lower unit engine.
⚠️ Attention: The inflatable floor of the NDND becomes harder when cold water is hit, and softer in the sun. Always check the pressure before going out and pump the cylinders if necessary to maintain driving performance.
There are enough liner cables inside the cockpit to attach the gear, which is an important aspect for anglers. pole-transom It allows you to quickly convert the boat to the engine if you need it. Anchor 320 It is a universal tool for different tasks.
Assembly and descent preparation
The process of preparing the boat for launch takes a certain time, and you need to be prepared for this. Having an inflatable floor requires sequential pumping of the cylinders first and then the bottom itself to ensure the correct geometry of the hull. Using a quality pump with a gauge is a prerequisite for the long service of the product.
☑️ Checklist for boat preparation
The first step involves laying the boat on a clean surface, free of sharp objects, branches and stones. Even a small knot can damage the fabric, so the litter or a special platform will significantly extend the life of your boat. Pumping. is made in stages: first cylinders to working state, then, after straightening the folds of the bottom, the final pressure is carried out.
It is important to ensure that the valves are tightly closed and protected from sand and dirt that can interfere with the tightness. After assembly, it is recommended to leave the boat in the sun for 10-15 minutes to check the pressure, as the air inside will heat up and the pressure will rise. Check-up seams and joints before each descent - a rule that saves from trouble on the water.
The boat must be thoroughly dried for storage and transportation, especially if used in salt water or muddy river, and salt and silt can corrode adhesives and fabrics when stored in rolled-up form for long periods. Packaging should be free, without excessive compression, to avoid cloth cloth cloth on the folds.
Expert advice: Always bring a repair kit and a piece of soap to the water. Soap water helps you quickly find a puncture site for the emerging bubbles, and a repairman will fix the hole right on the shore.
Operation with and without motor
Boat. Anchor 320 designed with the expectation of installing an outboard motor with a capacity of up to 5 hp, although many consider 2.5-3.5 hp to be the best option When using more powerful units, there is a risk of overweight of the stern and loss of controllability, especially when moving against the current or wave. Tranza It is quite robust, but requires (regular inspection) for cracks and backlashes.
On propelling, the boat behaves predictably, although it is inferior in speed to specialized rowing models due to the shape of the cylinders. For short runs or maneuvering in quiet weather, oars are an excellent addition, requiring no fuel and complex maintenance. Aerodynamics The body allows you to develop a decent speed for an outboard motor, saving fuel.
When operating with an engine, it is important to correctly set the angle of inclination of the lower unit so that the boat does not google on the planing. inflatable floor creates a certain resistance to water compared to the aluminum body, so it can take a little longer to get to the plane. speed It is very comfortable for cruising and fishing.
Owners should be aware of the resource of the squirrel board and the amplifying plate. Frequent overloads or impacts on logs can damage this structure, so maneuvering in overgrown reed areas requires increased caution. Careful attitude The sleeves extend the life of the entire boat.
Care, storage and durability
The durability of a PVC boat depends on its storage conditions and regular maintenance, and after each operation, especially in salt water, the hull must be thoroughly washed with fresh water and dried. MoistureThe remaining in the folds of the fabric can lead to the appearance of mold and an unpleasant smell, which is then difficult to get rid of.
Store the boat should be in a case, in a dry room at a temperature that excludes freezing or overheating. Sharp temperature changes adversely affect the elasticity of PVC, making the material more brittle over time. The ideal storage temperature is from +5 to +20 degrees Celsius.
⚠️ Warning: Never keep the boat rolled up immediately after fishing if it is wet, guaranteed to rot the fabric and break the seams within one season.
Periodically, it is recommended to treat the surface with special means to protect PVC, which restore elasticity and protect against UV rays, such compounds create an additional barrier to prevent color burnout and the appearance of microcracks. Regular services It also includes checking the pressure in the cylinders and lubricating the valves with silicone.
Proper drying and storage at room temperature is the guarantee that the boat Anchor 320 will serve you 5-7 years or more without loss of tightness.
Frequently Asked Questions (FAQ)
Will Anchor withstand a 320 trophy pike or a large perch?
Yes, the cylinder design and PVC material are strong enough to support the weight of large fish, but when poaching trophies, you should use a bolt to prevent the thorny fins or teeth of the fish from damaging the side, and it is also important to avoid the fish from hitting the side at full speed.
Can I use this boat in winter for fishing?
The use of PVC boats in winter is possible, but it requires extreme caution: the material in the cold swells and becomes brittle. Before going on the ice, the boat must be kept warm, and in the cold avoid any shocks and sudden movements. cruising around the ice boat in winter shoes is absolutely forbidden.
Which pump is best suited for this model?
For pumping cylinders and the bottom of NDND, it is best to use a two-mode foot pump with a pressure gauge. Electric pumps are convenient for primary pumping, but the final pressure (especially for the bottom) will still have to be finished manually or with a special compressor with precise control of PSI.
Is it possible to build a boat for one person?
Yes, with the use of an inflatable floor of NDND and a relatively light weight, one person can easily handle assembly and launching, but carrying a boat assembled with motor and gear alone will be difficult, preferably using a trolley or a partner's help.