Choosing the first boat is always a balance between the desire to get the maximum functionality and the need to meet a limited budget. flyboat Three meters and twenty centimeters long from Flinc has become a real bestseller in the Russian market, combining availability and time-tested design, and many boaters consider this model as the ideal entry ticket to the world of outdoor activities on the water, which does not require complex maintenance.
However, behind the external simplicity hides many nuances that determine the durability and comfort of operation. Flinc 320 Often referred to as a “workhorse” for fishing alone or together, but is it suitable for your specific tasks? In this article, we will examine the real possibilities of the case, the features of the engine installation and the hidden advantages that are not always written about in advertising booklets.
It's worth noting that the popularity of the model has spawned many modifications and fakes, so it's important to understand what exactly you're buying. Competent approach to the selection of equipment will avoid disappointments and save money on upgrades in the future. Below is a comprehensive analysis that will help you make an informed decision.
Design features and quality of materials
The basis of the reliability of any inflatable vessel is the material from which its cylinder is made. Flinc 320 reinforced PVC The density of the fabric directly affects the resistance to puncture and abrasion on the bottom, especially if you plan to pull the boat on pebble shores or rocky beaches without special protection.
An important element of the design is kielsonIt's a squirrel that runs along the bottom, and it not only reinforces the bottom, but it also serves as a guide for the installation. cross-plate Without a hard keel at speeds above 15 km/h, the boat can start to prowl, losing course stability, which is especially noticeable in lateral winds.
⚠️ Attention: When buying, pay attention to the quality of the seams. If you see glue bubbles or uneven joints, this may indicate a violation of the gluing technology, which will lead to etching of the air at the most inopportune time.
The engine trawl is made of moisture-resistant plywood and is covered with special enamel, which is usually removable in the 320, making it easier to transport, but requires careful drying after each fishing trip. Inflatable cans (if selected in the configuration) is much lighter than wooden, but less resistant to mechanical damage by sharp objects.
To increase the life of the PVC fabric, it is recommended to treat it with special UV protection air conditioning after each trip, especially if the boat is stored outdoors or in the balcony.
Dimensions, weight and transport specifications
One of the main arguments in favor of Flinc 320 In a packing bag, the boat takes up the minimum space in the trunk of a passenger car, making it ideal for spontaneous trips into a pond. The weight of the kit without motor and equipment is about 28-30 kg, which allows you to carry it to one person, although it is still inconvenient to do it for long distances.
The model's load capacity is stated by the manufacturer in the area of 350-400 kg. Theoretically, this allows you to accommodate two adult fishermen with all the equipment, but in practice, it feels most comfortable on it is one person or a couple with a minimum load. passport capacity leads to a decrease in the height of the board above the water, which increases the risk of flooding with a wave.
- 🚗 Length in the package: about 100 cm, which allows you to stow the boat across the cabin or in a small trunk.
- ⚖️ Weight distribution: the centre of gravity is shifted to the stern when installing a heavy motor, requiring proper seating of passengers.
- 🎒 Modularity: the ability to use the boat only with oars or to complete the engine and attachments.
Transportability is not just about size, it's also about assembly time. It takes 10-15 minutes for an experienced user to pump cylinders and install stiffness elements. Using an electric pump with auto-stop function significantly speeds up the process and ensures compliance. pressureThis is critical to preserving the geometry of the bottom.
Motorization: engine selection and speed indicators
The choice of engine for Flinc 320 It's particularly acute, because it's not just about speed, it's about safety. The maximum engine power recommended for this model is 5-6 hp. Installing a more powerful unit can cause the transom to collapse or lose control, turning the boat into an unguided projectile.
The optimal choice is considered by many owners to be two-stroke engines with a capacity of 3.5-5 hp They provide access to planing with one person on board and develop speeds up to 20-25 km / h Four-stroke analogues are heavier, which for a small boat can be critical, as it shifts the center of gravity and reduces the useful loading capacity.
| Engine power (hp) | Number of people | Mode of traffic | Average speed (km/h) | Fuel consumption (l/hour) |
|---|---|---|---|---|
| 3.5 | 1 | Full gas. | 12-14 | 0.8 - 1.0 |
| 5.0 | 1 | planing | 22-24 | 1.2 - 1.5 |
| 5.0 | 2 | Full gas. | 16-18 | 1.5 - 1.8 |
| 6.0 | 1 | planing | 25-27 | 1.6 - 2.0 |
When operating with a motor, it is important to consider the length of the lower unit. Flinc 320 Short lower unit (S) is ideal, as long can rest on the bottom when rolling or in shallow water. transom-wheelAs manually dragging a boat with an installed engine and tank is quite difficult.
⚠️ Warning: Never start the motor out of water or with a raised lower unit – this will overheat and jam the water-cooled pump in seconds.
Comfort and ergonomics on the water
Despite their small size, manufacturers are trying to improve ergonomics as much as possible. Flinc 320A key element of comfort is a hard bottom, which can be made of floorboards (aluminum or plywood sheets) or be inflatable low pressure (LDPL). Hard floorboards provide better course stability and allow you to stand more confidently during the throw of tackles.
Built-in pockets For the little things, the spinning holders and the perimeter liner cable are the little things that make a simple inflatable boat a full-fledged fishing tool. D-ring for anchoring, sonar or hinged hazel allows you to organize the space efficiently without cluttering the cockpit.
☑️ Checking before getting on the water
However, it is worth considering that the cockpit width of the 320 is not large, and two fishermen will be a little cramped to turn around, especially if you use bulky winter gear or large tackles. ergonomics It gives way to functionality, and each movement must be coordinated.
Comparison with competitors and modifications
There are many analogues on the market, such as Hunter 320, Flagship 320 or Aqua 320. Flinc This is a series that is distinguished by the balance of price and build quality, and unlike some competitors, it is more likely to use double bottom or reinforced protection, which increases the survivability of the boat.
The modifications may vary by the type of bottom (inflatable or rigid), the presence of a reinforced transcreant under the electric motor and the color of the fabric. Camouflage coloring is popular among hunters, while bright colors (salad, orange) are preferable for cruising purposes for reasons of consideration. safety And watery visibility.
Special attention should be paid to the possibility of installation electric motorFor quiet fishing in pressurized waters, this is ideal, the electric motor is lighter than gasoline, requires no fuel and allows you to maneuver with high accuracy, which is important when fishing in a snag.
The secret of durability of the transom board
To keep the trans from rotting, remove them after each trip, rub them with dry rags and leave them to dry upright, and once a season, it's good to treat the ends and slices with a special moisture-repellent compound for the tree.
Care, storage and extension of service life
Durability Flinc 320 The PVC material is afraid of open fire, sparks and prolonged exposure to direct sunlight in an inflated state (pressure increases inside the cylinders). After using the salt water, the boat must be rinsed with fresh water so that the salt does not corrode the fabric and accessories.
Keep the boat clean and dry, preferably straightened or folded without strong clogs. Sharp temperature changes are also undesirable, so a garage or storage room is preferable to an unheated balcony or shed. Regular check valve And the gluing places will help identify problems before they become critical.
- 🧼 Wash: Use soft sponges and soap solution, avoid aggressive chemicals and abrasives.
- 🌡️ Temperature: Do not leave the boat in the cold in a deflated form, the material can become brittle and crack.
- 🔧 Repair: Always have a remake kit with glue suitable for PVC and a piece of fabric for the lats on hand.
⚠️ Warning: Do not use solvents, gasoline or acetone to clean the boat – they can dissolve the top PVC protective layer, making the material sticky and vulnerable.
Proper drying and storage at room temperature is the guarantee that the Flinc 320 will last you more than 10 years without losing its tightness.
Frequently Asked Questions (FAQ)
Can the Flinc 320 be used to go to sea or only to rivers?
The boat is designed for use on calm water: rivers, lakes, reservoirs, access to the open sea or large bodies of water with high waves (see below).score above 2-3) is strongly discouraged because of the low side and the short length, which creates a risk of rollover.
What pressure does pumping cylinders require?
The optimal working pressure is 0.2 atm Exceeding this value in hot weather can cause the seams to rupture, so in the sun pressure must be controlled and if necessary, put out excess air.
How many people are comfortable on this boat?
Comfortable on Flinc 320 One adult with full gear or two adults with a minimum load is accommodated, and for long walks or active fishing with a large number of tackles, a single mode is preferred.
How to properly seal a puncture in the field?
You need to degrease the puncture site, apply glue (usually polyurethane), dry for 10-15 minutes, then apply the second layer and tightly press the patch. heat-impact (dryer or hot water in a bottle), if the specific glue instructions allow.
Do I need to register Flinc 320 in GIMS?
Under current regulations, inflatable boats less than 3 meters long and weighing less than 200 kg (along with the engine) are not subject to registration. However, if you install a motor more powerful than 8 hp (or 5 hp for some interpretations depending on the year of production and total power), the rules may change, so it is worth clarifying the current ones. standard in your region.