The modern inflatable boat has ceased to be just a budget means of transportation by water, turning into a full-fledged projectile for serious fishing and recreation. 300 WSW pilotThe silk car, which has gained popularity due to the optimal combination of price, quality of materials and functionality, is often the first serious acquisition for beginners, but experienced water engines appreciate it for its reliability and ease of maintenance.
In this article, we will discuss in detail all aspects of the operation of this modification, paying special attention to the design features and nuances that are often overlooked when buying. Hard Stringer. (WS) in the name is crucial for the running qualities of the vessel.
The three-meter (300 cm) dimensions are considered the gold standard for a single or a half-seater boat, the same size that can still be transported in the trunk of a passenger car, but which already allows you to confidently ride the wave and install a full outboard motor. Let's dive into the details.
Design features and materials
The basis of durability of any PVC boat is the material from which its body is made. The pilot 300 WS uses a five-layer reinforced fabric, which has high resistance to mechanical damage, ultraviolet radiation and exposure to fuel. The density of the material is usually 750 or 950 g / sq.m., which provides a balance between strength and weight of the product.
The key feature that the abbreviation indicates WSJIt is a structural element, which is a rigid insert (usually of plywood or composite) that runs along the side or is glued to the bottom, giving the body additional rigidity. Unlike inflatable keels, a rigid stringer does not require pumping and always retains its geometry, which has a positive effect on speed and stability.
The seams in quality boats, which include the model in question, are carried out by gluing the seams using two-component polyurethane-based adhesives, which ensure a tightness comparable to whole-cast products and eliminates stratification of the seams even when intensively operated in salt water.
When buying, be sure to check the quality of gluing the seams - they should not have bubbles, unpatched areas or sticking out reinforcement threads.
Bottom and rigidity system
The comfort and driving qualities of the boat depend directly on the design of the bottom. The pilot 300 WS is most often used high pressure inflatable floor (HPD) or plywood bottom with waterproof plywood with aluminum profiles. The presence of a rigid stringer allows you to minimize the deformation of the bottom under load, creating a “ski” effect, which is especially important when planing.
If you look at the inflatable floor, it's important to note that there are internal partitions that form a flat surface, which reduces the overall weight of the boat and makes it easier to assemble, because you don't have to insert and fix heavy sleighs. However, for long-distance fishing, many people prefer a hard bottom that better extinguishes the shocks against the wave.
What is the difference between NDND and floorboard?
The inflatable floor (BBB) is lighter, quicker to assemble and provides better germination on the wave thanks to its softness: the plywood bottom is tougher, more stable to stand on and easier to navigate, but assembly takes longer and the boat weighs higher.
An important safety feature is the presence of a hinge beam around the perimeter of the cylinder, which protects the hull from impacts on the pier, reed or side of another vessel. Pilot This element is made of rubber of high elasticity, which prolongs the service life of the main material.
Dimension, weight and load capacity
When choosing a boat, it is critical to understand its actual size and weight when assembled. For a 3-meter model, these parameters are compromises that allow you to manage the vessel alone, but with a margin for two people.
Below is a table with indicative technical specifications, which may vary slightly depending on the year of manufacture and the specific configuration:
| Parameter | Meaning |
|---|---|
| Length full, cm | 300 |
| Full width, cm | 136-140 |
| Load capacity, kg | 250-300 |
| Weight assembly (with motor), kg | ~35-40 |
| Passenger capacity | 2 people. |
It is worth noting that loading capacity 250-300 kg is not only the weight of people, but also the weight of the engine, battery, equipment and fuel, so for a comfortable fishing together with a full set of equipment, it is recommended to consider this boat as a one-and-a-half, or carefully monitor the total weight of the cargo.
Transportability is another great thing about this model: when deflated and packed in a bag, it can easily fit in the trunk of a mid-range sedan or in the back seat, and the weight in the pack is about 25-30 kg, which allows one person to carry the boat to the water without using a trolley.
Compatibility with motors and transoms
Train boat The 300-WS pilot is made of moisture-resistant plywood reinforced with aluminum linings or profiles. The transom is usually 38-40 cm high, which is the standard for most outboard motors. The design allows for both two-stroke and four-stroke engines.
The optimal power of the engine for this boat is in the range of 2 to 5 horsepower. Motors with a capacity of 2 hp will allow only one person to get on plane with a minimum load. For a confident exit to plane, two or with a load, it is better to consider options 3.5-5 hp Installation of a motor with a capacity of more than 6 hp is impractical and can be dangerous due to the power limit specified by the manufacturer.
For a boat 300 cm optimal choice will be the engine 3.5 hp - it will provide planing, but will remain light and economical.
When installing the engine, it is important to adjust the different correctly (engine tilt). Too large or small angle of inclination will lead to loss of speed, increased fuel consumption and reduced handling. The instructions to the boat always indicate the recommended settings of the installation.
Package and additional options
The basic equipment of the boat usually includes the boat itself, two inflatable seats (banks), a bag for packaging, a remix and a pump. Pilot.
- 🎣 Installation of rod holders: plastic or metal spinning glasses can be mounted on cylinders, which frees the fisherman's hands.
- ⚓ Anchor system: the presence of a nose loop allows you to fasten the anchor, and a special anchor rum facilitates its lifting.
- 💡 Lighting equipment: the possibility of installing running lights for navigation in the dark (compliance with GIMS rules is required).
- 🛡️ Protective elements: pranches (treads) on cylinders for protection from sharp objects and stones.
Special attention should be paid to the possibility of installation electric motorFor quiet fishing on pressed water bodies or for trolling, electric traction is the ideal solution, and battery weight becomes a critical factor in the weight of the boat.
☑️ Check before the first descent into the water
Operational and maintenance rules
To the boat 300 WSW pilot You've been here for years, and you have to follow a few simple but important rules, and PVC is a tough material, but it's afraid of open fire, sharp objects and prolonged overheating.
⚠️ Warning: Never leave a fully pumped boat in direct sunlight for long periods of time unattended. The air pressure inside the cylinders rises when heated, which can cause seams to rupture or the hull to deform.
After each operation, especially in salt water or muddy water, the boat must be thoroughly washed with fresh water and dried. Drying must be done in the shade, in the straightened form. Stacking a wet boat is a sure way to get mold and bad smell, which will be difficult to get rid of later.
Store the product in a case, in a dry room at a temperature of -20 to +40 degrees Celsius. Sharp temperature changes are less terrible than constant dampness. Regularly check the condition of the valves and if necessary pull them up with a special key from the remix.
FAQ: Frequently asked questions
Can a 300-horsepower engine be installed more than 5 hp?
Technically, it is possible to install, but this violates safety rules and can lead to loss of controllability or destruction of the transom, and it will deprive you of the possibility of registering with the GIMS without additional approval, since the power will exceed the permissible for a given length and design.
What is the optimal pumping pressure for cylinders?
The recommended working pressure is usually 0.2 atm (about 200 mbar or 2.8 psi). Do not pump cylinders above 0.25 atm, especially in hot weather. Use a pressure gauge to check, as it is difficult to determine the correct pressure by eye.
Do I need to register with the GIMS for this boat?
According to the current legislation of the Russian Federation, small vessels weighing more than 200 kg are subject to registration. engine-mountedSince the weight of a 300-wheel motorized boat up to 5 hp is usually less than 200 kg, registration is often not required, but laws may change, and the final decision depends on the inspector and the region.
How to seal the boat in the field?
There's always patches and glue in the remix. To be repaired reliably in the field, you have to degrease the surface (alcohol or acetone), sandpaper it, apply the glue to both surfaces, dry it and press it hard. Full polymerization takes 24 hours, but it holds it in a few hours.
⚠️ Warning: Using a boat without life jackets is prohibited by water safety regulations, and life and health are more important than any catch or comfort.
In summary, it can be said that 300 WSW pilot It's a reliable and time-tested option for those looking for a balance between mobility and functionality, and its proper operation and timely care will make it a sure-fire mate for many seasons.