Transportation floater It's always more of a question for owners than it is for a rigid case to be transported. PVC boat It is enough to simply throw in the back or tie to the trunk, without thinking about the risks of damage to the bottom and sides of the surface irregularity. trailer For this purpose, opens up new horizons of comfort and safety, if you approach the issue competently.
The problem is that the soft bottom of the boat is extremely vulnerable to friction and puncture, and a standard metal trailer frame, without proper preparation, will turn into sandpaper at high speed. paving This is the first and most important step before the start of operation of the car-trailer-boat bundle.
In this article, we will discuss in detail how to adapt the technique. Metal Service The right preparation will allow you to forget about blowing the cylinders on the way and enjoy fishing immediately upon arrival at the pond.
Features of the design of trailers MZSA for water technology
Factory MIZNA It produces some of the most mass-produced and affordable trailers in Russia, making them a popular choice for boat transport, and is structurally a welded frame made of profile pipe, which was originally designed for rigid loads. flyboat This means that the basic version needs to be improved.
The main advantage of these trailers is modularity and the availability of ready-made holes for the installation of additional elements. lay-up It's important to consider that standard galvanizing of the frame can wear off against the sandy bottom of the boat over time, so having a separation layer is critical.
The load capacity of MZSA models usually varies from 500 to 750 kg, which with a margin covers the weight of even large ones. PVC boat However, the distribution of this weight should be even, so as not to overload the breath and create dangerous situations on the track.
Surface Preparation: Lodge or Cross-Straights?
The choice of support type is the foundation of your boat's safety. There are two main approaches to equipping an MHSA trailer: using longitudinal support. laying-piece It's a cross-bar system, and each method has its own advantages and features.
Lodenters coated with carpet material or rubber provide support for the entire length. cylindersThis minimizes the risk of sagging and deformation of the case during prolonged parking, crossbars are cheaper and easier to install, but require more careful construction. fixers straps so that the boat does not move from side to side.
If you're a long-distance boat traveler, you'd better choose a bed, which dampens the vibrations and prevents friction. transom supports soft-coated.
Step-by-step instructions for installing supports
Installation of the support system on the trailer MIZNA It requires attention and technology, and you don't need to skimp on fasteners, because vibration on the road can weaken even the right screws.
First, you need to mark the mounting points or bars, the distance between the supports should correspond to the bending of the bottom of your particular boat model to ensure that the load is evenly distributed. After marking, holes in the trailer frame are drilled.
☑️ Checklist for the installation of supports
It's important to use growers Or self-contacting nuts when mounted, and the normal nuts can be unwinded by constant shaking, and it is also recommended that a layer of rubber be laid between the metal rack and the trailer frame to prevent direct metal contact and corrosion.
Once all the elements are installed, be sure to do a test load, put the boat down, inflate it to working pressure and check if there are any skews, and if necessary, the height of the supports can be adjusted by adding washers or adjusting the height of the pillars.
Proper fastening and slinging of the boat
The most important step is to fix the cargo, and you can't use conventional ropes because they tend to stretch and weaken. You'll need specialized ropes. snoring-belt (ratchet straps).
The boat is mounted at several points: the bow, the stern and the center. The bow belt prevents the boat from sliding backwards when braking, and the side and rear belts fix the position relative to the axis of the trailer. PVC material You can’t do that without deforming the cylinders.
⚠️ Warning: Never pass belts directly through the boat's valves or handles, which can cause the attachment elements to depressurize or tear off in transit.
For added security, use a rabies net or a special cargo net on top of the boat, which will prevent the belts from opening accidentally and protect the load from gusts of wind. hooks The belts are securely hooked to the trailer frame, and not over the sides of the boat itself.
Protecting the bottom and sides from damage
Even with the pawns, the risk of damage is still there, and the sand that gets between the bottom of the boat and the support works like an abrasive, so it is recommended that the pawns be cleared of dirt and debris before each loading.
A good solution is to use protective tent Or special linings made of dense fabric under the bottom of the boat, which is especially true if you plan a long parking trailer with a loaded boat.
How to keep a boat on a trailer in winter?
If you leave the boat on the trailer for the winter, be sure to lower the pressure in the cylinders to the minimum working or completely, if the design allows. Prolonged tension of PVC in the cold can lead to microcracks. It is also recommended to cover the structure with a wet awning.
Check your condition regularly carpeting If there are holes or abrasions, the material needs to be replaced. The metal base under the carpet should not contact the boat.
Traffic safety and GIMS
Operating a trailer with a boat imposes certain obligations on the driver. Speed mode must be reduced, especially on rough roads and when cornering. The center of gravity shifts, and the dynamics of the car changes.
Don't forget the requirements. GIMEThe trailer must be registered, have a license plate and a light alarm. The dimensions of the cargo (boats) must not exceed the permissible width limits, otherwise it will be necessary to install position lights on the boat itself or use the sign “Long-sized cargo”.
| Parameter | Recommendation | Critical significance |
|---|---|---|
| Trailer tyre pressure | 2.0 - 2.2 atm | Less than 1.8 atm |
| Speed on the track | 90 km/h | More than 110 km/h |
| Belt tension | Tight, no sagging. | Deformation of cylinders |
| Checking of anchorages | Every 50-70 km | After 300 km |
Tip: Before the first full-load trip, make a few laps around the garage or empty area, which will help you feel the dimensions and behavior of the trailer when reversing.
Pay special attention couplingBefore each trip, check the reliability of the breath and stop lights. Faulty light alarms are one of the most common causes of fines and accidents.
The safety of transporting a PVC boat on a MZSA trailer does not depend on the price of the equipment, but on the regularity of checks of the anchorages and the condition of the support surfaces before each trip.
Frequently Asked Questions (FAQ)
Can I transport a PVC boat assembled with an installed engine?
Technically, it's possible, but it's not recommended, because the motor puts extra stress on the transom and shifts the center of gravity, and the vibration can damage the lower unit, and it's better to take the motor off and carry it separately in the trunk or body.
Do I have to put the boat down before transportation?
You don't have to descent completely, you have to inflate the boat to work pressure to keep in shape, but in hot weather, you have to lower the pressure a little bit, because in the sun, the air inside the cylinders will expand, which can cause the seams to rupture.
How often should you change the carpet on the floor?
The life of the coating depends on the intensity of operation. On average, with active use (20-30 visits per season), carpet or rubber linings should be replaced every 2-3 years, or as through scuffs to metal appear.
Will the trailer of the MZSA 8113 withstand a boat 4.5 meters long?
Yes, the 8113 has a platform length of about 3 meters, but with the overhangs and the correct installation of the supports, the boat is 4.5 meters long and the main thing is to distribute the weight correctly so that the main load falls on the axle of the trailer, not on the breather.