Fishing and hunting on the water require a reliable boat that can withstand difficult operating conditions. PVC boat It is a special place because of its accessibility and proven design, and many aquatic motorists consider this brand as a starting or primary for fishing in medium water bodies, and in this article we will discuss in detail the technical nuances, pros and cons, as well as the features of the operation of these products.
Choosing an inflatable vessel is always a compromise between weight, load capacity and price. Company Dive For many years, we've been delivering budget solutions that are still in demand, and it's important to understand that in this price segment, you don't have to wait for premium materials, but basic safety requirements are generally met. Let's look at what this product is today.
The main material for the production of the body is a multilayer reinforced PVCThe design of the cylinders involves several independent compartments, which ensures buoyancy even if one of them is damaged, and it is the reliability of the material that is a key factor in the choice between different manufacturers of the budget segment.
Design features and materials
The design is based on a classic scheme with inflatable tubes and a hard or inflatable floor. PVC boats Dive Most often equipped with a low-pressure inflatable floor (LDPB) or plywood/aluminium plywood system. The use of reinforced polyvinyl chloride allows the product to maintain elasticity at low temperatures and not stretch excessively in the sun.
The seams in the products are made by cold or hot gluing, depending on the specific model and year of production. Welding technology It's more reliable because it creates a monolithic compound that doesn't break down over time, but when it's done properly, it can last for years without losing its tightness.
⚠️ Warning: When buying, be sure to check the quality of gluing the seams for the presence of bubbles or unpaved areas, as this is the main source of problems during long-term operation on water.
Special attention should be paid to the transom board, which is inserted into a special pocket at the stern, it is made of water-resistant plywood and sheathed with plastic or reinforced with fiberglass. Tranza It must be perfectly adjusted so that the motor does not create excessive vibration and does not shift during movement.
Technology of cylinder production
The production uses five-layer reinforced PVC density from 750 to 1100 g / m2. This provides high tensile strength and resistance to gasoline and oil.
Comparison of models: Dive 280, 320 and 360
The manufacturer's line covers a variety of needs, from single pleasure options to full-fledged two-seater boats. 320The silk is considered the "golden mean" in terms of load capacity and dimensions in the assembled form, smaller versions are suitable for calm water, and larger ones are suitable for loading by two fishermen with full equipment.
Below is a comparative table of the main specifications of popular modifications, which will help determine the choice:
| Model | Length (cm) | Width (cm) | Load capacity (kg) | Kit weight (kg) |
|---|---|---|---|---|
| Dive 280 | 280 | 130 | 250 | 24 |
| Dive 320 | 320 | 145 | 350 | 29 |
| Dive 360 | 360 | 150 | 450 | 38 |
| Dive 400 | 400 | 160 | 600 | 45 |
When choosing a size, it is important to consider not only the number of passengers, but also the method of transportation. Dimensions in packaged form The 360 and 400 may be critical for small car owners, but the 280 with a powerful engine will be difficult to plane together.
Installation of attachments and transom
The operation of the boat is impossible without properly installed equipment. transom plate It's the foundation for the motor attachment, so it needs to be given the most attention, and it needs to go into pockets with effort, but without distortion, so that it can be vertically lower unit.
The motor is fixed with a special stop or belt, which is often included. motor or a petrol unit, make sure the height of the transan (usually 381 mm or 508 mm) meets the requirements of your engine.
- 🛶 Make sure the air supply valves are closed and protected from water and dirt before installing the motor.
- 🔧 Check the tightening of all bolts on the trans board after the first 15 minutes of engine operation under load.
- ⚓ Use the safety crease for the engine so that in case of breakage of the transom, the engine does not sink.
The sides also have liner cables that are used to anchor or anchor equipment, and they can't be used for towing or mooring, because they're not used for anchoring. tear-up They're limited. It's better to use special reinforced points in the bow to attach the anchor beam.
Properly installed transom is a guarantee of no vibration and safe glides, do not skimp on checking this node.
Assembly and preparation for launching
The assembly process takes 10 to 20 minutes depending on experience and air temperature, and in cold weather, the material becomes stiffer and the cylinders are harder to straighten. Algorithm of action It always starts with laying the boat on a flat surface, free of sharp objects and debris.
Inflate cylinders to a state of solid elasticity, but not pumping them above normal. The pressure in the cylinders should be 0.2-0.25 atm. foot-pump With a pressure gauge allows you to control the process and avoid deformation of the seams due to excessive pressure, especially if the boat is in the sun.
⚠️ Warning: Never leave a fully pumped boat under direct sunlight unattended, as heating the air inside the cylinders can cause the seams to rupture.
After pumping the cylinders, the bottom is set up, and if they are floorboards, they are assembled into a single flat structure and inserted inside. The inflatable floor (BND) requires separate pumping to a pressure of 0.2-0.3 atm, which gives the vessel excellent seaworthiness and rigidity. Underbody rigidity It directly affects speed and controllability.
☑️ Checklist before getting on the water
Operation and care of PVC
The life of the product depends on how it is cared for, and after each fishing, you need to wash the salt, sand and silt with fresh water. Aggressive environmentsGasoline or oil should be removed immediately using special PVC cleaners to avoid damaging the material structure.
Keep the boat in a dry, cool place, in a straightened or slightly deflated state. It is not recommended to store the product in a compressed form for a long time, especially at low temperatures, as this can lead to scrap-room Periodically check the valves for leakage.
If a puncture or cut occurs, you can repair it yourself with a remix, the damage is cleaned, degreased and sealed with a special patch using PVC glue. It is important to follow the drying technology and press the patch with a load.
To extend the life of the rubber valve seals lubricate silicone grease once a season so that they do not dry out and keep the pressure.
Advantages and disadvantages of the model
By analyzing the experience of owners, there are a number of objective pros and cons. priceIt's a very popular boat for aspiring anglers, and it's also very resilient on the water because of the design of the cylinders.
However, there are also disadvantages associated mainly with the weight of the kit and the quality of the accessories in the basic versions. Heavy floorboards Plywood adds extra pounds, which is critical when carried over long distances, and there are also occasional complaints about the quality of the bag-package, which can break when used actively.
- ✅ Low cost compared to competitors of similar size.
- ✅ The presence of a reinforced keel in some modifications, improving the exchange rate stability.
- ❌ A large weight in the assembly with a plywood bottom, inconvenient for carrying by one person.
- ❌ Basic paddles often prove too short or heavy for comfortable rowing.
In the end, PVC boat It's a tool for those who are looking for a balance between price and function, and it's not without its drawbacks, but when handled carefully, it can last for many seasons, enjoying a steady fishing experience.
What is the maximum pressure that can be applied to the cylinders?
The optimum working pressure is 0.2-0.25 atmospheres, and exceeding this value (more than 0.3 atm) can cause seam strain, especially in hot weather. Always use a pressure gauge for monitoring.
Can I use a boat in the sea?
Use in marine conditions is only possible in calm weather and near the shore. Salt water is aggressive to material and fittings, so thorough washing with fresh water after each exit is required.
Which engine is better for the 320?
For the model 320, the optimal engine will be a 5-8 hp engine. This will allow you to go to the plane with one or two passengers. Motors with a capacity of 2.5-3.5 hp will provide only displacement mode.
How is the NDNDD different from the PDD?
BND (low pressure inflatable floor) is lighter, more compact to assemble and provides better seaworthiness. The plywood (plywood/aluminum) bottom is tougher but heavier, takes longer to assemble and takes up more space during transportation.
How to keep a boat in winter?
Store it clean, dry at temperatures between -10 and +20 degrees. It is best to hang it in a straightened state or fold it, but not squeeze it with heavy objects. It is recommended to check and pump the cylinders every six months.