In the world of inflatable fleet model Solar 350 It is a vessel that is often chosen by anglers who need a stable spinning or trolling platform but are not willing to tolerate the bulkiness of large boats, and is built on time-tested solutions that combine the strength of the material with the thoughtful geometry of the cylinders.
The main feature that distinguishes Solar 350 The main thing about the competition is that it's a bottom reinforcement system, it's a tank protection system, it's a 3.5-meter long boat that can handle enough loads for two or three people with a full set of gear, and it's important to understand that the right weight distribution on the deck directly affects the rideability and handling on the wave.
Many newcomers mistakenly believe that all boats are the same, but it is the details of the assembly and the quality of the seams that determine the durability of the product, and in this case the manufacturer has used a technology of double-stitching seams, which significantly increases the tightness of the joints. The operating pressure in cylinders is 0.25 atm, which is the standard for this class, but exceeding this value in the sun can cause the seams to rupture.
Structural features and materials of the body
The body is based on five-layer high-density reinforced PVC, which is resistant to ultraviolet radiation, gasoline, oil and salt water. Balloons They are divided into three compartments, which ensures buoyancy even if one of them is punctured, and this scheme is mandatory for safety certification.
At the bottom of the boat is a reinforced ribbon that protects the bottom from abrasion by sand, shell or rocky shores. Solar 350 And you should pay special attention to the tension of this tape, because when it fits properly, it affects the aerodynamics of planing, and on the side, welded handles are made of durable rubber, comfortable even with gloves.
⚠️ Warning: When storing a boat in winter, do not allow material to bend at an acute angle, this can lead to the formation of microcracks in the reinforcement layer.
The tray insert is made of moisture-resistant plywood and is covered with special enamel. It is rigidly fixed in pockets, providing reliable traction. For the Model 350, the installation of motors ranging from 5 to 15 hp is recommended. More powerful units can create excessive cavitation and damage the transom during sharp maneuvers.
Seam technology
What's the secret to strength?: Solar boat seams are hot-glue-over-layered, creating a monolithic structure that's stronger than the material itself. Unlike cold-glueing, hot-glue avoids separation at temperature extremes.
Bottom types and deck rigidity
The most important element of comfort is the bottom system. Solar 350 The two most relevant options are low pressure inflatable floor (LDPB) and hard aluminium floorboard or plywood, depending on the purpose of operation: floorboard is often chosen for fishing in standing water, and for cruising fishing and family walks - NDNDB.
The hard floorboard provides a perfectly flat surface that is comfortable to walk on, and allows you to install the chair on a rotating base, which takes longer to build because it requires a consistent installation of stringers and solder sheets, but on the water you get a feeling close to the rigid body.
- 🛶 Aluminum profile: light, does not rust, dries quickly, but can be slippery in wet form.
- 🪵 Plywood plywood: heavier, requires drying after each operation, but is cheaper and provides excellent stiffness.
- 🎈 inflatable floor: maximum comfort, lack of rigid elements, but less planing speed due to the flexibility of the bottom.
When installing a pipe system, it is critical to tighten all connections correctly, a weak tightening of the stringers will cause a hump in the middle of the boat, which will worsen the hydrodynamics, and if you pull the elements, you can damage the internal valves or deform the profile.
☑️ Complementary floor assembly
Driving performance and management
On the water. Solar 350 It's a very confident behavior, even in moderate chop, and the shape of the balloons is designed to effectively dissect the wave, minimizing impacts on the water, but it's worth remembering that the inflatable boat has less inertia than the metal boat, and it reacts more sharply to distortions of the cargo.
The management is directly dependent on the location cargo Shifting the center of gravity closer to the nose can cause the nose to bury in the wave, and shift to the stern can cause yaw and difficulty in getting to the planing. The optimal is weight distribution, in which the boat goes with a small gap at the stern.
⚠️ Warning: When driving at high speeds, always keep your hand on a kill switch attached to your clothes so that the engine will instantly stall in the event of a person falling overboard.
To improve the course stability, many owners install transoms or hydrofoils on the leg of the engine, which allows you to adjust the angle of the trim and reduce the load on the transom. At speeds above 20 km / h, the boat enters planing mode, which significantly saves fuel.
Compatibility with motors and attachments
Choosing a motor for Solar 350
It's about balancing weight, power and budget, and lightweight two-stroke engines, 5-9.9 hp, are the middle ground, and they allow you to get a boat with two passengers to plane and they can be easily transported in the trunk of a car.When installing attachments, such as sonars or GPS-navigators, it is important to keep the mounts tight, often using special brackets attached to the bank (seat) or sides, and it is not recommended to drill cylinders for the installation of stationary holders.
| Motor type | Power (hp) | Weight (kg) | Recommended load |
|---|---|---|---|
| two-stroke | 5.0 | 19 | 1-2 men, quiet move |
| two-stroke | 9.9 | 26 | 2-3 people, gleaming |
| four-stroke | 6.0 | 25 | 1-2 people, economy, economy |
| four-stroke | 9.9 | 34 | 2-3 people, comfort |
Electric motors are also a viable option for this model, especially for fishing on pressurized water bodies. Traction batteries are heavy, so it is better to place them on the bottom in the bow for balancing, using special sealants.
Use transom wheels only to move on solid ground, and in sand or water, they should be removed or raised, so as not to create unnecessary resistance and damage the cylinders.
Rules of operation and care of PVC
Durability Solar 350 is not only dependent on the quality of materials, but also on proper maintenance. After each launch, the boat must be rinsed with fresh water, especially if it is operated in a salty environment, and sand and salt act as an abrasive, gradually destroying the protective layer.
Drying is a critical stage. Wet material rolled up in a tight bag is quickly covered with mold, which corrodes the fabric, and the boat needs to be dried in the shade, because direct sunlight with pumped cylinders can lead to thermal expansion of air and rupture of the seams.
- 🧼 Cleanup: Use a soft sponge and special PVC products, avoid solvents and gasoline.
- ☀️ Storage: The ideal temperature is from -20 to +40 degrees, in straightened or semi-curled form.
- 🔧 Repair: For minor repairs, use the remixes that come in the kit, having previously degreased the surface.
If you notice a loss of pressure, don't rush to look for a hole. Often, the cause is a thermal compression of air or a valve that is not tightly closed. Check the valves first using soap solution.
Regular treatment of PVC fabric with special air conditioners (once a season) restores the elasticity of the material and protects it from ultraviolet radiation, prolonging the life of the boat by 30-40%.
Frequently Asked Questions (FAQ)
How long does it take to assemble and disassemble the Solar 350?
The build time depends on experience and type of bottom. For the version with NDNDM (inflatable floor), the process takes 10-15 minutes. If you use a pyeol system with an aluminum profile, it takes 20-30 minutes to set the floor and pump the cylinders to working pressure.
Can I use a boat in winter in low temperatures?
Operation is possible, but it requires caution. PVC becomes hard in the cold, so you only need to pump the boat in the cold, not in the heat. A sharp blow to the ice can lead to damage. After use, the boat cannot be immediately warmed up - it must be heated gradually.
What is the maximum weight you can load on a Solar 350?
rated carrying capacity is usually about 450-500 kg, however, for comfortable and safe plane with the engine, it is recommended not to exceed the load of 250-300 kg (including the weight of the boat, engine, fuel and crew).
How to seal the boat if there is no remaplet at hand?
In emergency cases, you can use a piece of PVC from an old boat or even a dense rubber chamber planted on polyurethane glue (for example, for shoes), but this is a temporary measure, and full repair with warm-up seam is necessary at the earliest opportunity.