Finding a reliable and compact boat for family vacations or fishing often leads a potential buyer to a model. Regat 340This range is considered the “middle ground” in the inflatable boat world, as it allows three adults to comfortably accommodate while maintaining mobility. Unlike the lighter two-seater variants, this model is already able to withstand a more serious wave and confidently carry an outboard motor with a capacity of up to 8-10 horsepower.
Owners often say that it is flyboat The 3.4-meter long model is their first major acquisition, marking the transition from simple rowing rubbers to full-fledged motor craft, and typically involves a low-pressure inflatable floor (LDPH) or solder floor, which has a significant impact on driving performance and plane speed. Understanding the nuances of operation and performance will help you make the right choice.
Purchased Regat 340You get a universal waterwalk tool that, if used properly, will last for years, and it's important to remember that the quality of the build and the materials in this market segment is critical to not only comfort, but also safety on the water.
Structural features and materials of the body
The basis of durability of any inflatable boat is the material from which its balloon is made. Regat 340PVC multilayer reinforced fabric is generally used, which is resistant to ultraviolet, gasoline, oils and mechanical damage. The density of the fabric is usually at least 750 g / sq.m., which provides high strength of the seams and protection from punctures when in contact with rocky bottom or branches.
Particular attention should be paid to the system. floor-floorThis design allows the boat to get on plane faster and provides a softer wave ride than rigid floorboards, however, the rigidity of the floor in such models depends on the pumping pressure, which must strictly comply with the manufacturer's recommendations specified in the product passport.
⚠️ Attention: Do not pump cylinders and bottoms under direct sunlight to maximum pressure! The air inside heats up and expands, which can cause joints to rupture or deform the structure. Leave a small margin of pressure when pumped in the sun.
Seams in quality boats are made by gluing using two-component glue, which guarantees the tightness of the joints. Tranza reinforcements The mounting area is made of extra layers of fabric, preventing the stern from deforming under engine load, which is a critical element, because this is where the maximum vibration loads are concentrated when driving.
Why is five-layer PVC important?
The multilayer structure of the material includes a mesh cord that works like reinforcement in concrete, which is the layer that prevents the boat from stretching under pressure and provides strength specifications, allowing it to withstand impacts and friction against the ground without forming microcracks.
Equipment and ergonomics of internal space
The interior space of the model Regat 340 The cylinders are often more than 45-50 cm wide, allowing you to comfortably position your legs and not feel cramped during long crossings. The ergonomics of the seats (cans) also play an important role: they can be rigid (plywood or dural) or inflatable, which affects the overall weight of the equipped boat.
Standard equipment usually includes not only the boat itself, but also the necessary accessories for the start of operation. transom wheels And the carry bag is often in the basic set, which eliminates the need to buy them separately, and the presence of a reinforced transom allows you to install motors with a shorter leg or standard length, depending on the model.
For ease of control in the nose is often provided squirt Or an anchor ring, and a liner cable around the perimeter of the balloon, which is not only for insurance, but also for the ability to pull the boat to the shore or the dock, and some versions have special pockets for storing small things, which increases the overall comfort of use.
☑️ Checking the completeness when buying
Driving qualities and compatibility with motors
Driving specifications Regat 340 The boats of this size are perfectly on course and have good stability. When you install the engine with a capacity of 5-8 hp, the boat confidently goes to plane with one passenger, and if you have two people, goes into displacement mode or requires a more powerful engine for planing.
The optimal power of the motor for this model varies in the range from 5 to 10 hp The use of more powerful engines is possible, but requires caution and compliance with the rules of loading, so as not to overload the transom and not to disturb the balance. planing Such boats start at a speed of about 20-22 km / h, which allows you to quickly overcome long distances.
The shape of the keel is an important aspect: the presence of an inflatable keel (if provided by the model) greatly improves the course stability and the ability to cut the wave, especially when driving against the wind or in large water, where the boat behaves predictably and does not prowl from side to side.
To save fuel and increase engine life, try to keep the boat in planing mode at full load. Prolonged movement in transient mode (when the nose is raised, but there is no planing yet) creates maximum load on the engine and transom.
Technical specifications compared to analogues
To objectively assess the potential Regat 340You need to look at the basic parameters in numbers, and this data will help you compare the model with the competitors and understand how it meets your requirements for load capacity and dimensions.
| Parameter | Meaning | Note |
|---|---|---|
| Full length | 340 cm | Overall size |
| Full width | 150-160 cm | Depends on the pressure. |
| Load capacity | 500 kg | Including boat weight |
| Passenger capacity | 3 people. | Optimum 2+1 |
| Boat weight (bottom) | 45-55 kg | Depends on the configuration. |
Comparing these figures with analogues, it can be seen that loading capacity The buoyancy allows you to take on board additional equipment, anchor, sonar and fuel without the risk of overloading. The width of the cylinders also contributes to stability, making it a reliable choice for fishing.
Rules of operation and storage
And Regat 340 And you have been faithful to this for years, and you have to follow a set of rules of operation, and after every trip, especially if it's in salt water or a contaminated water, you have to wash it thoroughly with fresh water, and that removes salt, sand and organic residues that can break down the PVC structure or cause corrosion of the fittings.
Drying is a critical step before packaging, and even the minimum amount of moisture inside a rolled-up boat can lead to mold and a bad smell that is very difficult to get rid of. Valves. They must be open during drying to allow air circulation in all compartments.
⚠️ Warning: Never keep the boat rolled up immediately after use without first drying. Wet fabric is the ideal medium for fungus development, which destroys the reinforcing layer and reduces the tightness of the seams.
Storage should be carried out in a cool, dry place, protected from direct sunlight and rodents, the optimal storage temperature is room, but without sudden changes, it is recommended to periodically, once a season, pump the boat and check it for pressure loss to detect possible microdamage in time.
Proper drying and storage in straightened or semi-rolled form prolong the life of the boat by 2-3 times compared to storage in tight twists in a damp garage.
Home repair and maintenance
Even the most reliable boat can require repairs. Regat 340 It's a field-based repair kit, always a remix that contains a piece of cloth and glue, and for more serious repairs, like valve replacement or cut fixing, you might need a dryer to heat the glue and a roller.
The process of gluing requires careful surface preparation: degreasing (acetone or special means) and cleaning. Two-component polyurethane glue It provides the best adhesion and elasticity of the seam, which will not burst when the cylinder is deformed. It is important to apply glue on both glued surfaces and to withstand the technological pause.
Regular maintenance also includes greasing rubbing parts, checking the condition of slings and accessories. If you notice that the boat has begun to poison the air faster than usual, use a soap solution to find the leak site.
How do you glue PVC properly?
The secret to good gluing is temperature and pressure, the glue must be warm (about 40-50 degrees), and the gluing site after joining must be rolled strongly from the center to the edges to squeeze all the air and ensure close contact of the layers.
Frequently Asked Questions (FAQ)
Can I use the Regat 340 in winter?
Using PVC boats in subzero temperatures is possible, but it requires extreme caution. The material in the cold swells and becomes brittle. Any sloppy movement, impact on the ice or bending can lead to cracks. If operation is necessary, the boat should be kept warm until the last moment and avoid sharp bends.
What is the optimal engine weight for this model?
For Regat 340 The optimal motor is a motor weighing up to 20-25 kg, which allows one person to easily transport the engine and install it on a transom. More powerful and heavier motors (30+ kg) can overload the stern and make it difficult to control, especially alone.
How often should I pump a boat in the heat?
In hot weather, the pressure in the cylinders can increase. If the boat is on the water under the sun, it is recommended to periodically vent excessive pressure through the valve to avoid rupturing the seams. On land, it is better to keep the boat in shade or slightly deflated.
Is it really possible to assemble and disassemble this boat?
Yeah, assembly and disassembly. Regat 340 It's a very easy process for one person, although it's going to take some physical effort, and having an inflatable floor (BBB) makes it much easier than the solder versions, where you have to stack and dock heavy floor slabs.