Legendary Ufim 22 It has proven itself as a reliable boat capable of withstanding the harsh conditions of Russian water bodies. PVC Owners often face the need to find quality components to restore driving performance or repair minor damage after the active season.
Finding original or compatible parts can be a real quest, given the variety of modifications and year of release. In this article, we will discuss in detail which nodes most often fail, where to look for reliable suppliers and how to correctly replace key components yourself. repair This will extend the life of your boat for many years.
Don't ignore the small scuffs or loosening of fasteners, because on the water, any small thing can cause a serious problem. Timely replacement of consumables is the key to your safety and comfort while fishing or cruising. Next, we will look at the main categories of spare parts and features of their installation.
Repair and replacement of the inflatable floor of the NDNDM
One of the most expensive parts of the structure is bottom (NDM) That's what takes the surges and the water pressures when it's planing, and if you notice that the boat has gotten worse on mode or has been deflected, it might be time to check the pressure and integrity of the bottom cylinders.
A frequent problem is a violation of the tightness of the valves or the appearance of microcracks in the places of folding tissue. Ufam 22 It's very hard, but over time, even these materials lose their elasticity, and in critical cases, you need to completely replace the bottom section, which is a complex but doable procedure in a workshop.
⚠️ Warning: Never use water-based household adhesives for bottom repair, as they will not withstand the pressure and tear load when moving on water.
When choosing a new bottom, it is important to take into account not only the dimensions, but also the rigidity of the used PVC materialToo soft bottom will lead to a decrease in speed, and too hard can create excessive stress in the places of attachment to the cylinders.
How to check the tightness of the bottom without water?
Soap the surface with soap solution and apply pressure, and the bubbles will indicate where the leak is, and look carefully at the seams and valves.
Furniture and fasteners
Metal elements on the boat are exposed to constant moisture, sun and mechanical stress. fasteners Or loosening the switches is a signal to act immediately. Ufamke 22 It is often required after several seasons of active fishing.
And you have to pay special attention to the rods and the rod holders, and these are made of stainless steel or brass, but even these can corrosive when the protective layer is damaged. fittings ensures reliable fixation of oars and safety of passengers.
- 🔩 The keys are turning - provide a comfortable stroke and folding of oars.
- 🎣 Spinning holders are necessary for comfortable trolling fishing.
- ⚓ Anchor rims are a critical element for safe parking.
- 🔗 Leier rings are used to fasten safety ends and equipment.
When installing new elements, you must use them. PVC-plate And it's a reinforcement patch made of the same material that the boat is made of, which guarantees that the connection is monolithic.
Valve replacement and puncture repair
The most common malfunction is loss of leakage. valve boat Ufim 22 It's required if it's not holding air or scrolling, and the replacement procedure is simple, but it requires precision and temperature.
Special remixes are used to repair punctures and cuts, and it is important to choose the right fabric: it must match the density and color of the main material of the boat. Repairs Small damage can be done directly on the shore, if there is a tool at hand.
| Type of damage | Patch material | Type of glue | Time to dry |
|---|---|---|---|
| Puncture to 2 cm | PVC | Two-pronged | 24 hours. |
| Cutting the seam | PVC tape | Polyurethane | 48 hours. |
| Valve replacement | Round paycheck | Special PVC | 12 hours. |
| Bottom scuffing | Liquid PVC | Not required | 6 hours |
Remember to degrease the surface before applying the glue. Using acetone or alcohol greatly improves adhesion and makes the connection durable. Poorly glued patch can come off at the most inappropriate moment.
Warm up the gluing with a hair dryer after drying (no more than 50-60 degrees) to activate the glue and increase the strength of the connection.
transom board and its reinforcement
The trans is the back of your boat, carrying the weight of the engine. Ufam 22 It's a very common thing to have motors up to 10 to 15 hp, which puts a lot of pressure on the squirrel board, and over time, the tree inside can start to rot and the coating can break down.
If you notice a transom deflection or visible damage to the laminate, you need to urgently repair it. replacement It's a complex operation that requires partial disassembly of the aft.
⚠️ Note: Operation of a boat with rotten transom is strictly prohibited - this can lead to loss of the engine and overturning of the vessel during a jerk.
To strengthen the transom, additional stainless steel linings or aluminum profiles are often used, which distributes the load from the outboard motor and prevents deformation. PVC tubes at the point of contact.
☑️ Translation diagnostics
Seats and boat cans
The comfort of the water depends on the quality of the seats. Ufamke 22 They can become uncomfortable or lose their fasteners over time, and replacing them with soft, anatomical seats improves ergonomics.
Modern. seat They have removable covers that are easy to wash and dry, which is important for maintaining hygiene and tidy appearance of the boat. Fixing new cans usually does not require drilling new holes, if the regular spaces under the boat are used. lyctrose.
When choosing new interior elements, pay attention to the material of the filler. It should be moisture resistant and not absorb the smell of fish or gasoline. Aluminum profiles of cans should be anti-corrosion coating.
Where to buy original parts
The sourcing issue is acute, as the market is flooded with counterfeit goods. Ufamki It is best to purchase from official dealers of the manufacturer or in specialized stores of water-motor equipment.
When ordering through online stores, carefully study reviews and photos of goods. Cheap counterparts often differ in color and fabric quality, which can spoil the appearance of your boat. Original PVC It has a specific roughness and density.
- 🏭 Official dealers of the Ufa Shipyard plant.
- 🛒 Large marketplaces with a section "boating".
- 🔧 Specialized service centers for repair of PVC boats.
- 🤝 Verified communities of owners of Ufimka boats in social networks.
Don't chase the lowest price. Quality parts last for years, while savings can lead to re-repairs in one season. Water reliability is more important than short-term benefits.
Buying original components from the official ensures the compliance of sizes and materials, which is critical for tightness and safety.
Frequently Asked Questions (FAQ)
Where to find a cutting scheme for replacing the bottom on Ufimka 22?
Precise patterns are rarely published in the public domain due to copyright. It is best to take measurements from your boat yourself or contact a workshop specializing in tailoring PVC boats. Self-cutting without experience can lead to a skewed design.
Can I replace the valve with another manufacturer?
Yes, you can, but you have to be very careful with the landing diameter and the height of the valve. Universal valves often require fitting the hole, which can weaken the structure.
How often should I change the slate?
If properly operated and stored, the transom can last 10 to 15 years, but annual inspection is mandatory, and if the boat is kept outdoors in the sun, the lifespan of the tree inside can be reduced to 5 to 7 years.
How to use PVC at home?
For quality repairs, two-component polyurethane adhesives are required. Single-component adhesives are suitable only for temporary repair or sealing of small punctures that do not experience tear loads.