The modern small boat market offers many options for water tourism and fishing, but among them a special place is occupied by the company. flyboat It's this class of swimmers, known as the NDNDM, that combines the portability of rubber products with the driving qualities of full-boats. Star He has become one of the leaders in this segment, offering solutions that are highly valued by both beginners and experienced boaters.
Choosing a particular model is often a difficult task, as many factors must be considered, from the type of cylinder material to the construction of the floorboards. Inflatable boats This manufacturer is characterized by a reinforced design and thoughtful ergonomics, which allows you to use them in difficult conditions. In this article, we will discuss in detail the features, advantages and technical nuances that will help you make the right decision.
Understanding design features is important not only when buying, but also during operation. PVC materials And this will extend the life of your boat for many years to come, and let's dive into the world of performance and see what these boats stand out from the competition.
Design features of the NDLD models
The main difference between boats with the acronym NDND is the presence of a low-pressure inflatable floor. float-upThis solution allows you to get a perfectly smooth surface that does not create turbulence when driving, which significantly saves fuel and increases speed.
The cylinders of such boats are usually divided into several independent chambers, which ensures that the vessel is not in a safe position. sluggishness Even if one of the compartments is damaged, the bow structure is often reinforced with a keel, which can be both inflatable and rigid, which improves course stability. It is important to note that the bottom rigidity is achieved due to the high pressure in the cylinders, which makes the surface comparable to hard analogues.
The use of high-quality materials allows you to withstand significant loads. PVC reinforced It is resistant to puncture, abrasion and ultraviolet radiation, which is critical for long-term operation on the water, and it is the combination of these factors that makes this type of vessel one of the most popular among fishermen.
It is also worth mentioning the stringer system, which some models may not have, because the rigidity is provided by the design of the cylinders themselves. However, larger versions use additional stiffness elements, which allows the load from the engine and passengers to be distributed more evenly.
Materials and production technologies
Basis for boat production Star It's a dense reinforced polyvinyl chloride, and it's a multilayer composite, where there's a grid of synthetic strands between the PVC layers. reinforcement It gives the material tensile strength and resistance to mechanical damage, and the quality of the welding is a critical factor in determining the durability of the entire product.
The production uses a technology of gluing cross-plated with two-component polyurethane glue, which ensures the tightness of the seams, which is not disturbed even with prolonged exposure to water. Heat treatment Some of the nodes are further enhanced by making them virtually inseparable, ensuring that the boat can withstand extreme loads.
⚠️ Attention: Using cheap adhesives or breaking the drying technology of the seams during repairs can lead to depressurization of water cylinders. Always use original remixes and follow the manufacturer's instructions.
The bottom of boats is often protected by additional rubber or denser PVC linings. protector-belt They take the brunt of the impact of pulling a boat ashore or coming into contact with rocky bottoms, and the color scheme of materials is usually tailored to mask, which is especially true for hunters and anglers.
Secrets of PVC durability
With proper care and storage in a dark, dry place at temperatures ranging from -10 to +30 degrees, the service life of quality PVC can exceed 10-15 years.
The fittings used to fasten cans, switches and fry bolts are made of stainless steel or high-strength alloys, which prevents corrosion and breakage at the most inopportune time. Quality fittings - This is a guarantee of safety and ease of operation.
Comparison of models: which to choose
The manufacturer's lineup includes many modifications, varying in size, load capacity and design features. For single fishing, compact two-seater options are often chosen, which are easily transported in the trunk of a passenger car. roomy with increased load capacity.
When choosing a cockpit, you should pay attention to the length of the cockpit, because it determines the useful space. Models with the index "Lux" or "Profi" often have reinforced cylinders and an increased diameter, which adds to the value of the cockpit. floatability And the following is a comparative table of popular modifications.
| Model | Length (cm) | Width (cm) | Load capacity (kg) | Weight (kg) |
|---|---|---|---|---|
| Compact-2 | 280 | 130 | 350 | 32 |
| Tourist-3 | 320 | 140 | 450 | 41 |
| Profi-4 | 380 | 150 | 600 | 54 |
| Expedition-5 | 420 | 160 | 800 | 68 |
It is important to consider not only the dimensions, but also the power of the recommended engine. For small models, a motor of 5-8 hp is enough, whereas for large versions you will need to use the engine. power-drive Overloading the engine can cause water to trawl over the side and reduce handling.
For fishing, the best choice will be a model length of 320-340 cm, which will provide comfort and allow you to install a sonar with a battery.
Operation and preparation for launch
Proper assembly and pumping of the boat is the key to a safe and comfortable walk. Before getting on the water, you need to carefully check the pressure in the cylinders. Normative pressure It is usually 0.2-0.25 atmospheres (about 200-250 mbar), but in hot weather it can increase, which requires control. Insufficient pressure will lead to deformation of the bottom and loss of driving performance, and excessive pressure will lead to rupture of the seams.
It takes a little bit of time to build, especially if you've got a sequence of things going on, and you've got to decompose and pump the bottom, and then you've got to make sure that you don't have to leave the cockpit. foreign-stockThe deck should be flat, without folds.
The use of a transom wheel makes it much easier to move a boat along the shore, especially alone, and this accessory is attached to a transom and allows the boat to roll like a trolley. The transom wheel This is not just a convenience, but a necessity for those who often change places of descent.
⚠️ Warning: Never leave a fully pumped boat in direct sunlight for long periods of time unattended. Heating the air inside the cylinders can lead to a critical increase in pressure and valve rupture.
When installing the engine, make sure it is securely secured with rods. The engine must be located strictly in the center of the transom. slippage or damage to the transom board during movement.
Care, storage and repair
The durability of your vessel depends on how you care for it. After every fishing or walk, the boat should be washed with fresh water to wash away salt, sand and organic residues. fittingsDrying before packaging is a prerequisite to prevent mold and unpleasant smell.
It is best to store the product in a straightened or semi-folded form in a dry room, if this is not possible, it is allowed to store in a deflated state, but without heavy loads on top. Temperature conditions The storage should be stable, without sudden changes. The optimal temperature is room, but storage in unheated garages is allowed, provided that it is protected from frost.
If you get a puncture or cut, you don't have to panic, you can do some repairs yourself with a remix, you can degrease the surface, you put the glue on, you put a patch in the same material. Quality repairs restores tightness and does not affect further operation.
☑️ Seasonal boat service
Check valves regularly, sometimes sand or dirt can get into them, which will lead to air venting, and simple valve cleaning often solves the problem without having to replace the part. Preventive examination This will help you avoid unpleasant surprises on the water.
Tuning and additional equipment
The basic equipment of the boat can often be improved with the help of additional equipment. quilt Or reinforce the transom, if the design allows, and many owners also install additional pockets for gear, rod holders and sonars.
To increase comfort, long hikes are fitted with soft pads on cans (seats), which allows you to sit for several hours without discomfort. Comfortable seats With a backrest, a hard jar is turned into a full-fledged chair, and awnings and canopies that protect against sun and rain are also popular.
Installing an anchor ditch in the bow makes anchoring easier, especially when fishing in windy weather. A cat anchor weighing 2-4 kg is the best choice for boats of this class. Anchor system It should be reliable and quickly accessible.
Install a special plastic or rubber tread (heel) on the transom, which will protect the lower part of the transom from the shocks of waves and abrasive wear when moving, significantly extending its life.
Safety is also important, and life jackets, anchor end and scoop are mandatory under GIMS rules. Life-saving equipment It should be easily accessible, not hidden in a distant knob, and the right preparation will make your walk not only pleasant, but also safe.
What pressure should be in the cylinders in winter?
In winter, at low temperatures, the pressure in the cylinders drops. It is recommended to pump the boat to the standard 0.2-0.25 atm, but take into account that in the cold the material becomes less elastic. Do not pump the boat in a warm room before leaving for the cold - it is better to pump it immediately before launching.
Can I use the Star of the NDND for diving?
Yes, hard bottom models or NDBs are great for diving because of their stability and the ability to install additional equipment, but the load capacity should be considered when placing air cylinders and equipment.
How to wash a boat if it is very dirty?
Use warm water with mild soap solution to wash, avoid aggressive solvents, gasoline or acetone, as these can damage the top protective layer of PVC. After washing, be sure to rinse the boat with clean water.
How to fold the boat properly so as not to damage the bottom?
Stack the boat along the longitudinal axis, avoiding bending in the same places. Make sure the surface is completely dry before packing. Don't put sharp objects inside the cockpit before rolling.