Stand for spinning in a PVC boat: selection and installation

Fishing from a swimming facility is radically different from fishing from the shore, requiring not only skill from the angler, but also competent organization of space. Spinning stand in PVC boat It's one of the key elements of ergonomics that frees your hands to control oars or motors, and the lack of a quality holder often causes the gear to lie on the bottom, get tangled up, or, worse, fall overboard when a trophy is pulled.

In today's fishing industry, there are many options for rod locks, specifically adapted for the soft and slippery side of inflatable vessels. A properly designed design not only protects the expensive rod from damage, but also provides instant access to gear at the time of bite. In this article, we will discuss in detail the types of mounting, installation features and nuances of operation of various holder models.

Classification of holder designs for PVC boats

The first thing that fishermen encounter when they search for accessory is the huge variety of shapes and ways they attach. spin-stand We can divide these into a few basic types depending on the mechanism of fixation to the cylinder or the structure of the boat, and understanding these differences is critical, because there are almost no universal solutions that are ideal for all fishing scenarios.

The most common type is the model attached directly to the inflatable board, which can use a system of belts, Velcro straps or special suction cups. The second popular option is holders mounted on a transom board or rigid cockpit elements, if the boat is equipped with runduks or banks with the ability to install racks. Stiffness of fixation in each case will be different, which directly affects the choice of rod and wiring technique.

• 🎣 Covered models: fastened to the upper edge of the board, without requiring drilling or complex installation, ideal for quick installation.
• 🔩 transom holders: fixed on a hard board, providing maximum stability when working with heavy tackles.
• 💺 Modular systems: They are installed on rotary seats or special rails, allowing you to change the position of the rod in a wide sector.

Special attention should be paid to the combination options that combine the functions of a hold and an organizer for trifles. The choice of a specific type depends on how often you plan to change the location and whether you need prompt access to different gear. For active fishing in the wiring, rigid mounts are preferable, while softer options are suitable for passive fishing.

⚠️ Warning: When using inflatable cylinder attachments, always check the tension of the belts after the first throws. PVC material tends to stretch slightly under load, which can lead to weakening of the fixation and loss of tackles.

Manufacturing materials and their impact on durability

Aggressive aquatic environment dictates its requirements for the materials from which fishing accessories are made. Spinning stand It is in constant contact with water, ultraviolet light and sometimes fish slime or bait attractants, so the quality of the material is crucial. Cheap analogues made of ordinary plastic can quickly lose strength and crack in the sun, creating a dangerous situation.

The most reliable designs are anodized aluminum or stainless steel grade AISI 316. These materials are almost inert to salt water and do not corrosion. However, the metal can be heavier than plastic, which is important for small boats where every kilogram of cargo is important. Plastic models made of ABS plastic or polypropylene are also popular due to their lightness and low price, but require more careful handling.

An important element of the design are seals and gaskets, where the holder contacts the sides of the boat, soft but elastic materials such as: EPDM rubber They prevent PVC from rubbing and provide additional friction to keep the holder from slipping, and ignoring the quality of the seals can damage an expensive boat cylinder with sharp edges of the fastener.

• 🛡️ Stainless steel: absolute corrosion resistance, high weight, premium price.
• ⚖️ Aluminum alloys: excellent balance of strength and weight, requires high-quality anodizing.
• 💰 Engineering plastics: Low cost, low weight, shorter service life with active UV radiation.

When choosing, you should also pay attention to fittings: bolts, nuts and screws must be made of the same material as the base, or have a zinc coating. Using ordinary black steel in fasteners will negate all the corrosion resistance of even the most expensive holder.

Fixing methods: from belts to rods

The method of installation is perhaps the most important aspect that determines the usability of the accessory. Fixing the stand It should be reliable, but not damage the structure of the boat. For inflatable vessels, it is strictly not recommended to use methods that require puncture of the balloon or gluing elements, unless this is provided for by the factory design of the boat.

The most gentle and popular method is the use of wide textile belts with buckles-fastex or Velcro straps. Such systems cover the side on top and bottom, or are fixed only from above, resting on the inside of the board. For boats with a hard transcus or sleigh, rods are ideal for a dead grip. However, when using them, you need to make sure that the sharp edges of the scabs do not touch the fabric.

There are also magnetic holders, but their use is limited to boats with built-in metal elements or the ability to install a response metal plate under the fabric. PVC Magnets are inefficient because of the thickness of the balloon, and a more advanced solution is vacuum suction cup systems, but they require a perfectly smooth and clean surface, which is difficult to achieve when fishing.

⚠️ Warning: Never attach the holder to an inflated balloon "by eye." Inadequate tension of the belts will lead to the rod chatter, and the tug can deform the balloon, creating a stress point dangerous when the water temperature changes.

Installation of the holder: step-by-step instructions

The right installation will ensure the safety of your fishing and the safety of gear. Before you start installation, determine the optimal placement, given the length of the rods and the convenience of the cut. Usually, holders install in the cockpit area, closer to the rower or motorist, to access the gear without getting up.

The process of placing a mounted model on board the boat is as follows: first, you need to completely inflate the cylinders and let them stand for 15-20 minutes to stabilize the pressure, then try on the holder, straighten all the belts and make sure that they are not twisted, and then you make the final tightening of the fixing elements.

Sequence of action:
1. Clean the surface of the side of sand and moisture.
Place the holder on the top of the cylinder.
3. stretch the lower belts under the bottom of the boat (if the design provides).
Tighten the upper and lateral latchers evenly.
5. Check the angle of the holder's glass.

It is important to adjust the angle of inclination of the glass itself, into which the spinning handle is inserted. For fishing in a plumb or on bottom tackle, the angle should be closer to the vertical (70-80 degrees), and for running fishing with constant overthrows, more gentle (45-50 degrees) to facilitate rapid capture of the rod.

Nuances of installation on boats with inflatable floor

If your boat has an inflatable floor (BBB), it may be difficult to install holders with lower belts, in which case it is recommended to use models that are attached only to the upper edge of the side, or mount the holders on a rigid slate mat, if the design of the boat allows.

Comparison of popular models and specifications

To make it easier to choose, we have prepared a comparative table of the main specifications of the different types of holders on the market, these parameters will help you navigate the range and choose a model that meets your requirements for price and functionality.

Type of holder	Materials	Weight (g)	Compatibility	Price.
The Stylish Classic.	ABS plastic	150	Any boards.	Low.
Trans reinforced	Nerzh.	450	Boats with transoms	Medium
Modular rotary	aluminum	300	Special bases.	High.
Universal belt	Polypropylene	200	Any boards.	Medium

When analyzing the table, it is worth considering that weight In this context, it is not so much important for the overall load capacity of the boat as for the ease of transport and storage of equipment. Lightweight plastic models are easy to remove and put into a backpack, whereas metal structures often remain on the boat or require a separate cover to be transported to avoid scratches.

Also pay attention to the diameter of the glass. Standard dimensions range from 35 to 50 mm. If you use casting rods with massive handles or multiplier coils, make sure that the inner space of the holder allows the coll to freely enter to the end.

Operation and maintenance of fishing equipment

Even the best quality. spin-stand It requires regular maintenance, especially after fishing in salt water or in muddy (turbid) water bodies. Sand trapped in the fastening mechanism or inside the glass acts as an abrasive, quickly wearing out plastic elements and scratching metal. So rinsing with fresh water after each trip is a mandatory procedure.

Periodically check the condition of textile elements: belts, straps and Velcro. Under the influence of sun and moisture, synthetic fibers can lose strength. If you notice scuffing, decreased elasticity or fading of the fabric, the element is better replaced, so as not to risk losing gear in the middle of the reservoir. Metal parts can be treated with silicone lubrication to protect against oxidation.

Remember to check the reliability of the fixation before each step into the water. Vibration from the motor and waves can gradually weaken the tightening of the screws or belts. Simple preventive action will take a minute, but will save your rod from falling into the water or on rocks.

⚠️ Warning: Do not use aggressive solvents or acetone to clean holders, especially if they come into contact with the sides of the boat. Chemicals can damage the PVC protective layer, making the material sticky or brittle.

Frequently Asked Questions (FAQ)

Can I use a car holder for glasses in a PVC boat?

Theoretically, you can adapt the way you attach, but it's not recommended. Car holders are not designed to be in constant contact with water and salt, their mechanisms quickly rust. Also, their shape is often not suitable for spinning handles, which can be thicker or have a different geometry than a standard car glass.

What is the maximum weight of the rod withstanding the standard stand?

Most high-quality plastic and aluminum holders can easily withstand rods with a test of up to 150-200 grams and a total length of up to 3 meters. Problems can arise with heavy trolling "candies" or sea rods, for which it is better to choose reinforced metal models with additional support points.

Will the belt holder damage the side of the boat during long-term operation?

If properly fitted and soft pads are not, however, if sand or small pebbles fall between the belt and the side, it is possible to wipe the cloth when the boat is moving or winding, it is recommended to periodically correct the position of the belts and clean the contact surfaces of abrasive particles.

Are there holders for inflatable floor boats (BBBs)?

Yes, there are special models that are attached exclusively to the top of the cylinder or to rigid elements (banks, transom), without affecting the bottom. The use of classic models with lower belts on NDND boats is impractical, since the belts will deform the inflated bottom and interfere with a comfortable landing.