Any fisherman who spends time on the water knows how tedious it can be to hold a spinning spinning for hours, and the muscles become stiff, the attention becomes dull, and the risk of dropping a tackle into the water increases with every minute. rod-board It becomes not just an accessory, but a necessary element of comfort and safety.
The modern market offers many solutions, from simple plastic glasses to complex rotary systems. PVC boatsIt may be useless for metal "Kazanka" or "crowd".
In this article, we will discuss the main types of fasteners, consider the nuances of installation on different types of boats and even touch on how to independently manufacture reliable holders. A competent approach to choosing the location and method of fixation will allow you to focus on the bite, rather than finding a place for gear.
Types of structures and methods of fastening
The first thing that fishermen encounter when searching for accessories is the variety of form factors. Design of holder It depends on where you plan to place it and what gear you use, and the most popular option is a tubular glass, which is inserted into the handle of the rod.
There are also clip-on models that lock the form along the entire length, preventing it from falling out when pitching hard. signaler smack.
⚠️ Warning: Make sure the inside diameter of the glass matches the diameter of the handle of your spinning. Too wide the glass will lead to the rod boltanka, and too narrow will simply not let the tackle go down to the end.
The way you attach these supports, you can divide them into a few basic groups, depending on the material on the sides of your boat and the availability of space.
- 🔩 Invoices (on screws): fasten directly to the board or transom through drilled holes, ensuring maximum rigidity.
- 📌 On the suction cups: Suitable for smooth surfaces, but require constant monitoring of tightness and can be peeled off in the cold.
- 🧱 Injunctive: mounted in the planshira or deck, which requires a violation of the integrity of the structure, but gives an excellent result.
- 🧲 Magnetic: They are only relevant for metal boats, they allow you to quickly change position, but are afraid of the shocks of waves.
Each type has its advantages. Overhead models are reliable but require drilling. Suction cups are convenient for temporary use, but they can't withstand the heavy loads of catching large fish. Magnets are good for steel boats, but their grip strength must be very high.
Features of installation on PVC boats
Installing accessories on inflatable watercraft requires special sensitivity, and the main task is to ensure reliability without damaging the water. cylindersMost often, owners of PVC boats choose overhead models that are fixed on a transom board or inflatable elements.
For soft sides, there are special platforms with a wide base that distribute the load. If you plan to attach the holder to a hard transom, use stainless screws with a wide hat. Be sure to apply a sealant to treat the screwing sites to prevent moisture from entering the tree.
Some anglers prefer not to drill a trawler, but to use removable structures attached to stringers or cans, which allows you to quickly dismantle the equipment after fishing.
When PVC is mounted, use a rubber or dense fabric lining between the mounting metal and the balloon to exclude rubbing the material on the wave.
Hard fixing of the rod in this case can lead to breakage of the form when the boat rolls, it is better to use holders with a small backlash or shock absorbing insert.
Installation of holders on metal boats
Owners of aluminum and steel boats, such as "Crimea", "Ob." or "Voronezh"They have more freedom in the choice of fastening methods. Metal allows you to use powerful welded structures or bolt joints.
The most reliable method is to weld a glass to the board or deck, which eliminates the risk of losing gear even in the worst storm, and if welding is not possible, the method of drilling and installing rivets or nut bolts is used.
When drilling aluminum, be sure to use lubricant (for example, machine oil) so that the drill does not "burn" and does not bite the metal. The holes should be treated with an anti-corrosion composition and painted, since the broken layer of the oxide film is the beginning of the path to corrosion.
⚠️ Warning: When mounted on a metal side, make sure that the fastener hats do not interfere with the passage of the boat or tear clothes, it is better to use secret heads or cover them with plugs.
Metal boats also have magnetic holders, which allow you to quickly move the fishing rod from side to side depending on the direction of the wind or current. But you don't need to rely on a magnet to catch a large pike or pike, because a fish jerk can easily tear off even a powerful neodymium.
Homemade stands: drawings and materials
Why pay more for factory plastic when you can make a reliable thing yourself? Homemade stand It's often superior to the store's, and it's adapted to a particular boat, and it requires a minimal set of tools to make it.
The main material used is PVC pipes 50 mm in diameter or metal pipes of the corresponding diameter, the plastic is lightweight, does not rust and is easy to work, the metal is stronger, but requires protection against corrosion.
Drawing of a simple construction of PVC pipe
Cut the 15-20 cm pipe, brew one end or close it with a plug, drill two bolt holes 5-7 cm from the open edge, and you can glue a piece of bicycle camera to improve the fixation inside.
The manufacturing process is simple: the pipe is cut at an angle of 45-60 degrees (for the rod tilt), or left straight; the lower edge can be melted or closed with a plug; the mounting pad is welded or glued to the side to attach it.
If you make a holder of metal, be sure to hide sharp edges so as not to damage the fishing line and hands. You can paint the structure in a bright color, so it will be easier to notice if it accidentally falls overboard.
Comparative table of materials
The choice of material for the stand affects the durability and weight of the structure, and the following is a comparison of the main options used by anglers.
| Materials | Weight. | Corrosion resistance | Strength | Price. |
|---|---|---|---|---|
| Plastic (PVC) | Low. | High. | Medium | Low. |
| Stainless steel | Highly | Very high. | Very high. | High. |
| aluminum | Medium. | High. | High. | Medium |
| brass | Highly | High. | Medium | High. |
Plastic is ideal for lightweight gear and inflatable boats; stainless steel is the choice of professionals willing to pay for perpetual service life; aluminum is the middle ground for metal boat owners to avoid galvanic pairs when in contact with the hull.
For saltwater fishing (sea walks), use only stainless steel or titanium, as aluminum and brass will quickly break down.
Ergonomics and safety of use
Correctly installed fishing-staff Not only does it have to keep the gear, it also has to make fishing safe, and a boat rod is a potentially dangerous item, and if a fish jerks or a boat rolls, it can cause injury or loss of expensive equipment.
Arrange the holders so that the rod combo does not interfere with the operation of the oars or control the engine. The optimal height of the installation is just above the level of the board, so that when you cut the gear you can quickly remove the gear in one move.
- 🎣 Inclination angle: for bottom fishing, the vertical position is more convenient, for spinning - inclined (45-60 degrees).
- 🌊 Water protection: in the bottom of the glass, it is desirable to drill 2-3 drainage holes with a diameter of 3-5 mm so that water does not accumulate inside.
- 🔒 Fixing: Use a safety rope for valuable rods, especially when fishing from the board.
Remember that while the boat is going, the fishing rods must be taken out of the glasses. Punching "horns" can catch on the bushes near the shore or cause injuries to passengers.
☑️ Checking before getting on the water
Frequently Asked Questions (FAQ)
Can I attach the stand on the suction cup to the board of the PVC boat at full speed?
No, it's not recommended, it's designed to be parked or very calm, and at full speed, the vibration and pressure of the water are guaranteed to rip off the suction cup, and you risk losing gear or damaging the board.
What diameter of the pipe is optimal for spinning rods?
The internal diameter of 40-50 mm is considered standard. This is suitable for most cork handles and EVA. If you use casting rods with a "hatch", it is better to take a pipe with a diameter of 50 mm or make a special cut.
Do I need to make holes in the bottom of a plastic glass?
Without drainage holes, the glass will accumulate water, which will lead to wet handles (especially cork) and possible development of mold. 2-3 holes with a diameter of 3-4 mm are enough.
How to lubricate the thread of fasteners on a metal boat?
The best way to do this is to use lithium lubricant or special marine anticores. Ordinary solidol in the sun can leak, and graphite lubrication can create a galvanic pair. It's important to isolate aluminum from steel if the materials are different.
Can a holder be used for trolling?
Normal cups are not suitable for this. Trolling requires special outrigger holders or powerful structures with an angle of inclination, allowing the gear to work when the boat is moving, a regular glass will simply break out at the first stretch of the fishing line.