Deep-sea bream fishing from a boat has always been considered the domain of experienced anglers who know the habits of this cautious fish. The ring or egg method is radically different from coastal fishing or using bottom tackle with a classic cast, where the key to success is not the range of the throw, but the accuracy of vertical positioning of the nozzle in a narrow feeding plume.
This is a way of catching bed pits, deep-sea brows and watering, where the bream comes out to feed in the daytime, unlike coastal fishing, where the angler is limited by the terrain and range of the throw. boating It allows you to stand right above the stern, and a well-assembled gear and a well-chosen seat ensures you catch even in periods of sluggishness, when other methods are powerless.
Selection and preparation of fishing craft
The success of the event depends on the comfort and stability of your floating craft. PVC The wide side allows you to conveniently arrange fishing rods and cages, and also provides stability in the water turbulence, which is critical when working with long but sensitive nods.
However, lightweight aluminum "Kazanki" or "Voronezh" boats should not be discounted. The metal hull is more resistant to punctures on the shell and snags, which is often found on deep pits. The main requirement is the ability to securely fix the fishing rods. The board must be equipped with holders or have a rigid design for installing brackets.
The anchor system requires special attention. You need two anchors to securely hold the boat across the current (stretch). Using one anchor will cause the boat to turn stern or nose-to-drive, pulling the hooks off the stern table. The weight of the anchors is selected based on the strength of the current and sail of the boat, usually 3-5 kg each.
- 🚣 The optimal length of the boat for comfortable fishing is 3.4 meters.
- ⚓ Be sure to use two anchor systems for rigid fixation.
- 🌊 The presence of a transom board will facilitate the installation of rod holders.
- 🛡️ The bottom of the boat should be protected from sharp shells at the depth.
The boat approach should be as silent as possible. A sharp blow to the side of the jolly or loud conversations can scare the fish away for a long time from the fermented point. Use an anchor cord with minimal stretchability so that the boat does not blow away with gusts of wind.
Design of tackle: fishing rod and mounting of the ring
The ring fishing gear is structurally simple, but requires precision in assembly. It is based on a short angler 1.5-2 meters long. There is no point in using long rods, since the fishing is almost vertical, and a long whip will only interfere with the tight space of the boat. Most fishermen use homemade fishing rods made of durable fiberglass or old telescopic "leafers".
The central element of the system is itself ring This is a 50-60 mm metal or lead ring with a hole to allow the feeder line to pass and an ear to attach the main line. Lead rings are preferred because they are heavier and better at the bottom without moving. Modern models are often made as a cut egg with a spring clip, which makes it easier to install.
The main line is chosen monophilic, 0.25-0.30 mm in diameter, or wicker 0.12-0.14 mm with a high burst load. The tile is more sensitive, but the monophile is better at quenching the jerks of a large bream on the flow. The nod is installed powerful, rigid, often from a clock spring or a metal plate, capable of working under the strong tension of the flow of water.
⚠️ Warning: Never tie a fishing line to a ring tightly without a vertebral. When catching a large bream or hooking, the ring should slide freely along the fishing line of the feeder, otherwise you risk breaking the gear or losing the fish.
Special attention is paid to hooks. Since fishing is often carried out on barley, worm or worm, the hook should be wide, with a long forearm (No. 8-12 in international classification), the sting should be perfectly sharp, since the cut is made by carpal movement, and a dull sting will lead to empty bites.
Feed: the heart of bream fishing
Without a well-functioning feeder, fishing for the ring becomes chaotic poking with a fishing rod in the hope of luck. The feeder (often called "smoking") is a mesh bag of stainless netting or a large capron net with a large cell that holds 3-5 kg of bait, the shape of the feeder can be cylindrical or conical, the main thing is that it lies steadily at the bottom.
The principle of operation is based on the flushing of bait particles by a current that creates a plume visible to the fish. Breath, with an excellent sense of smell, climbs this plume against the current and finds your nozzle lying exactly in the stream. The volume of the feeder should be sufficient to ensure feeding for 2-4 hours without lifting.
The composition of the bait is a separate topic, and for a river with a strong current, the mixture must be heavy so that it does not immediately blow away.
- 🌾 Boiled millet (the main filler that creates volume).
- 🍞 Sunflower cake or ground seeds (aromatics).
- 🪱 Cutting worm, worm or moth (living component).
- 🟤 clay or soil for weighting and ligament.
It's important to calculate the viscosity correctly. If the feed is too dense, the plume will not form. If it is too loose, the feeder will empty in 20 minutes. The perfect consistency allows the feed to wash out gradually, forming a muddy path.
The secret ingredient for bream
Experienced anglers add some ground biscuits or corn sticks to the bait, and they create a steady mud in the water that attracts the bream from a long distance, causing it to linger at a point longer than usual.
Tactics of searching and installation of the boat
Finding a fishing spot is 80 percent of the success. Breath likes deep pits, beds, and areas with smooth but not too fast currents. The bottom should be hard, clay, shell, or sandy. The elbow bottom is not good because the feeder can sink, and the plume will not go down the bottom, but will go into the water column or into the silt.
The installation process begins with a sounder measuring the depths, and if you find a promising depth difference or plateau, you have to get upstream. The distance from the boat to the fishing point depends on the depth: the deeper you go, you have to put the boat up to the fishing line at an angle. The optimal angle of gear to the surface of the water is 45-60 degrees.
Starting order:
- Anchor and lock the boat across the stream.
- Lower the feeder to the bottom strictly from the side, where the fishing rods will stand.
- Lower the tackle with the ring, having walked the line through the hole in the ring.
- Smoothly lower the ring to the feeder, controlling the tension.
Once the ring is on the feeder, you have to pull the line and put the fishing line in the holder, the nod should be bent by the flow of water, now you have to wait for the fish to come, usually bream comes to bait 30 to 60 minutes after feeding.
If the current is very strong, use two rings on one line or a weighted egg ring so that the gear does not blow away from the aft stream.
Techniques of catching and catching trophies
The blister bite on the ring often looks like a confident, but not sharp, nod down. The fish standing against the current takes the nozzle and moves higher, weakening the tension or, conversely, pressing to the bottom. The cut should be short and sharp, the amplitude is not more than 20-30 cm. You do not need to make a wide swing, otherwise you can injure the fish or confuse the tackle.
The most critical thing is to get out of the way, and when you feel the cut, the bream starts to fight back, and your job is to keep it from going out, under other gear, or worse, under a boat, and you have to keep the line tight, working with your brush, and helping yourself with your second hand, picking a line, and if you get a large one, don't force the events, you have to tire the fish in the course.
When the fish comes to the surface, it needs to be carefully lifted, but there's a caveat: the ring is still on the fishing line of the feeder.
- 🐟 Bring the fish to the board without lifting high above the water.
- 🔓 Remove the ring from the fishing line of the feeder (if the design allows) or raise the feeder.
- 👐 Carefully remove the hook and send the bream to the cage.
The cage should be set so that the throat is in the water, and the net itself does not touch the bottom of the boat, so that the bream does not clog. In hot weather, it is better to lower the cage to a depth of 2-3 meters, where the water is colder and more oxygenated.
| Parameter | Optimal value | Permissible range |
|---|---|---|
| Length of fishing rod | 1.5 - 2.0 m | 1.2. to 2.5 m |
| Diameter of the line | 0.25 mm | 0.20 - 0.30 mm |
| Ring weight | 40 - 60 g | 30 - 80 g |
| Size of hook | № 10 | № 8 - № 12 |
| Weight of the feeder | 3 - 5 kg | 2 - 7 kg |
The secret to success is to keep the line tight, and the line's slack on the current will cause the gear to become entangled against the stern cord.
Typical errors and security measures
Despite the apparent simplicity, beginners often make mistakes that negate all efforts. One of the most common is the wrong choice of place. Fishing in scorched areas or in reverse-flowing "boilers" often ends in hooks and cliffs. Choose clean areas with a flat bottom.
Another mistake is to use too rough gear. Breathing on the flow, especially in clear water, can be careful. Thick fishing line sails on the flow, knocking off the nozzle from the fed stream, and alerts the fish. Use high-quality but thin fishing lines of proven brands, such as: Shimano or Sunline.
Safety on the water is priority number one: fishing from a boat, especially in depth and using heavy loads, requires compliance with the rules:
⚠️ Warning: Always carry life jackets for passenger numbers. Do not stand up in a full height PVC boat in high winds or excitement - this can lead to a rollover.
Also worth checking is the condition of the gears. A worn fishing line on the ring can burst at the most inopportune moment, and you will lose not only the fish, but also an expensive ring. Regularly check the last 2-3 meters of fishing line before each outing.
☑️ Checking before getting on the water
Which is the best way to use a ring?
The best nozzle is a large dung worm, a bunch of squirrels or boiled barley. The worm is good because it is active and attracts attention, and barley is perfectly hooked when strong currents. Often anglers use a sandwich: a worm with a squirrel or a barley with a mastress.
Can I catch the ring at night?
Yes, night bream fishing is very effective, especially in summer, and at night the bream comes closer to the shore and to smaller places, but additional training is required: having a good lantern, fireflies on nods and knowing the place during the day so as not to get confused in the dark.
What to do if the ring is stuck on the feeder?
If the ring (especially the whole one) is stuck on the feeder, don't pull sharply. Try picking the slack of the feeder line, pulling it closer to the boat and gently loosening the ring. If it's an egg, make sure the clamp mechanism isn't clogged with debris or shell.
Do you need a sonar to catch the ring?
Sound sounder is highly desirable, but not strictly necessary, and it helps you find the exact bottom relief, detect the eyebrow or the pit, and see the approach of the fish, and without the sounder, you have to rely on experience, knowledge of the reservoir and the pumpkin method, which greatly reduces the efficiency of fishing.