Finding a quality and durable solution to protect the bottom and sides of the swimmer is a challenge that every owner faces. Synthetic cover in the boat to buyThe modern market offers many options, but it is important not to make a mistake with the choice of supplier and type of material, so as not to overpay for unnecessary functions or, conversely, not to buy a low-quality product.
In this article, we will take a look at what synthetic textiles are, why they are becoming the standard for inflatable boats, and where to buy, and learn about the specifications, nuances of installation and real prices, which will help you make an informed decision. Competent approach The choice of decking will extend the life of your vessel and make fishing or cruising much more comfortable.
Many beginners underestimate the importance of proper flooring, focusing only on the motor or anchor system, but it is the floor that takes the brunt of boarding a boat, moving cargo, and contacting water. synth And it solves a lot of problems: it doesn't rot, it doesn't dry quickly, it doesn't slide, and let's see why this is the material that's worth your attention.
What is Syntec and Why is it Better than Plywood
Syntec is a high-tech material based on polypropylene filaments that undergo special heat treatment, and unlike natural wood or even moisture-resistant plywood, synthetics are completely inert to water. Plywood sheetsEven those lacquered, they gain moisture over time, they get heavier and they start to rot, creating the perfect environment for bacteria and bad smell, and Syntec is completely devoid of these drawbacks.
The key advantage of the material is its structure, because the pile of the carpet does not absorb water, but passes it through itself, remaining dry to the touch, and this is critical for safety, because the risk of slipping on the wet bottom is minimized. coating It has excellent thermal insulation, which is especially appreciated by fishermen in the cold season, when contact with the cold PVC bottom of the legs can be uncomfortable.
⚠️ Warning: Don't confuse conventional household carpet with marine syntec. Household options can release toxins under ultrafi and quickly lose pile, while specialized material for boats is stable and durable.
Synthec is durable for decades, resistant to sun-blooding, non-fluid, and easy to clean, and if plywood floors require periodic repainting and drying, then it is non-fluid. synthetic flooring Just rinse with water from a hose, which makes it the leader in the tuning segment of PVC boats.
Where to buy synthetic coverage: an overview of markets and suppliers
The question is, where exactly? Synthetic cover in the boat to buyThere are many options, and each has its own pros and cons. Large marketplaces offer a wide range of options, but often sell material at high prices or in rolls that are inconvenient to transport. Specialty water-motor stores are a more reliable option where you can get advice.
For many, the best solution is to order directly from manufacturers or large distributors who are engaged in cutting into sizes, which allows you to get exactly the piece you need without overpaying for extra meters. When choosing a supplier, pay attention to the availability of certificates and real customer feedback about the density of the pile and the quality of the base. Cheap syntec It can quickly "bald" in places of active cruising.
- 🛒 Specialized online stores: offer ready-made cutting for popular models of boats (Kazanka, Flagman, Miv, etc.), which simplifies installation.
- 🏭 Material manufacturers: They are sold in rolls, profitable for workshops or large boats, but require independent cutting.
- 📦 Marketplace: convenient and fast, but the risk of running into a product of poor quality or inappropriate density is high.
When buying, it is important to consider not only the price per square meter, but also the density of the material. For boats, it is recommended to use syntec with a density of at least 600-700 g / m2. Thinner options wear out faster and hold the shape worse. It is also worth clarifying whether the material is sold with an already applied adhesive layer or needs to be glued yourself, as this affects the final cost and complexity of work.
When ordering material, ask the seller to add 5-10 cm to your size for allowances, which will allow you to perfectly fit the coating in difficult places near the cylinders.
Comparison of prices and producers: specifications table
The price range in the market can be significant, and it depends on a variety of factors: density, availability of anti-slip impregnation, brand and volume of purchase. To make it easier for you to navigate, we have prepared a comparative table of popular options, the data are relevant for the current season and may vary slightly depending on the region.
| Type of material | Density (g/m2) | Estimated price (ruble/m2) | Term of service |
|---|---|---|---|
| Budget Syntec (China) | 450-500 | 400 - 600 | 2-3 years |
| Standard (Russia/Turkey) | 650-750 | 700 - 900 | 5-7 years |
| Premium (Europe) | 800-900 | 1200 - 1500 | 10+ years |
| Slate mat (ready) | Combined | 3000 - 5000 (pcs) | 5 years |
As you can see from the table, the price difference between the low-cost and premium segments is significant, but if you plan to actively operate the boat, you can see that the price difference is very high. material-saving Cheap synthetics lose their pile more quickly, and in a couple of seasons you'll be faced with a choice: change the coating or put up with discomfort, and investing in quality material pays off with comfort and no need for frequent replacement.
Also worth considering is the cost of related materials such as glue. If you buy a material without adhesive, you will need a special adhesive for PVC and fabrics. Cheap adhesives may not withstand the tearing loads when inflating a boat, so this component is also not recommended to save. High-quality glue It ensures the monolithic structure of the floor.
Instructions: how to properly open and lay the coating
The process of installing synthetic coatings requires care and preparation. If you decide to do the work yourself, you'll need a sharp knife, a ruler, a marker and perhaps a glue. Before you start, the boat needs to be completely inflated and let it stand for several hours to straighten all the folds, which will ensure the accuracy of the cutting.
First, you do a pattern of paper or old cardboard if the shape of the boat is complicated. In simple cases, you can mark the material right on the bottom, leaving small margins at the edges. You need to cut the syntec on the front side so you don't damage the pile and see the cutting line. The knife movement must be confident and continuous.
☑️ Checklist before editing
If the material requires gluing, apply the glue in a thin layer to the bottom of the boat and on the back of the synthetic. Let the glue dry according to the instructions (usually 10-15 minutes), then press the material tightly, smoothing from the center to the edges to expel the air. It's important. prevent the glue from getting on the front part of the pile, since it will be almost impossible to remove it then.
⚠️ Warning: Never apply a synthetic "stretching" coating before sticking. When pumping the boat, the bottom may deform slightly, and if the material is pulled, it may detach or go in waves.
Caring for synthetic flooring in a boat
One of the main arguments in favor of the decision Synthetic cover in the boat to buy Unlike plywood, which requires drying after every trip, synthetics forgive many of the errors of use, but for the material to last as long as possible, you need to adhere to simple hygiene and storage rules.
After every fishing or day on the water, it is recommended to rinse the floor with fresh water, especially if you have swam in salt water or in bodies of water with abundant vegetation. The sand and fine dirt, stuck between the villi, work as an abrasive and can accelerate the wear of the threads when cruising.
How do you dry syntec?
Synthetic carpet dries very quickly. Just shake off the water and leave the boat straightened in a draft or sun for 15-20 minutes. You can roll a boat with wet syntec, but you better let it dry to avoid the musty smell in the closed case.
Keep a synthetic boat in a straightened or loose folded state, and you should not put heavy objects on a rolled-up boat in the place of the floor bend, so as not to break the base of the material. flooring It retains its presentable appearance and functionality for many seasons.
Frequent errors in selection and installation
Despite its apparent simplicity, many users make common mistakes that negate the benefits of the material, one of the most common being trying to use adhesives that are not designed for PVC or polypropylene, which causes the coating to move away in stockings at the first severe load or temperature drop.
Another mistake is choosing a material that is too thin in the hope of saving money, a thin synthetic quickly wiped under the heels of shoes or spikes of boots, and often ignored the need to degrease the surface of PVC before gluing, which dramatically reduces adhesion. Quality of surface preparation This is 90% of the success of the entire operation.
- 🚫 Use of inappropriate glue: This leads to the detachment and deterioration of the material.
- 🚫 Consistency savings: The slender pile quickly tramples down to the base.
- 🚫 No tolerances: This leads to the appearance of gaps at the sides after shrinking the material.
To avoid these errors, you can carefully study the material manual and consult the seller before buying. Feel free to ask about the compatibility of the glue and the type of synthetic. Remember that the work will take longer and more money to rework than the original quality installation.
The main secret of floor durability is not only the quality of the synthetic itself, but also the correct glue, as well as careful preparation of the PVC surface before installation.
FAQ: Frequently asked questions
Can I put a syntec on an already installed plywood floor?
Technically, it's possible, but it's not recommended, and the plywood will soak up water and rot under the syntec, creating a hotbed of corrosion and smell, and it's better to dismantle the plywood, treat the bottom of the boat, and put the synthetic coating right on the PVC.
How much does the sun heat up in the sun?
The synthetic material heats up less than dark PVC or metal, but it can be warm in the direct sun, but it doesn't get hot to the point where you can't step foot, and it cools down quickly when you get water.
Do I need to shoot Syntec for the winter?
No, you don't have to remove the coating, it's resistant to frost and temperature, and you can store the boat assembled or rolled up with the synthetic material glued on it without losing its properties.
Can I wash the syntec with a kercher?
Yes, high-pressure washers are acceptable, but it is better to steer the jet at an angle and not bring the nozzle close to the pile so as not to damage the structure of the threads.
In summary, it can be said that the decision Synthetic cover in the boat to buy This material combines durability, aesthetics and functionality, saving the owner from many problems associated with wooden floors. The right choice of supplier, careful installation and minimal care will ensure your boat takes a second breath and make every outing a pleasant event.