Boat Fishing opens up possibilities for the spinner that are not available to the coaster, but the classic long rods in the limited space of the cockpit turn from a tool of prey into a source of constant problems. side-pinning - specialized equipment designed taking into account vertical wiring and cramped conditions.
Many beginners make the mistake of trying to adapt short ultralights to shore fishing without understanding the fundamental difference in tests and formation. Fishing requires tight control of the bait at depth and instant reaction to the bite that dictates their requirements for the form. In this article, we will examine all the nuances of choosing and operating such a tool.
The right gear allows you to ignore the wind, the current and the swing, ensuring a stable catch even in difficult weather conditions, and the wrong choice will lead to constant overfishing, bait breakage and, as a result, spoiled mood. Let's determine what exactly makes the flightman indispensable assistant on the water.
Design features of on-board rods
The main difference between the onboard spinning and the classic “stick” version lies in its geometry and load distribution, the standard length of such models rarely exceeds 1.5-2 meters, which is dictated by the need to control the tackle with one hand and a limited range of swing. Short form provides the stiffness necessary to penetrate the mouth of a predator at depth.
The materials here are special. Often high-module graphite with reinforced walls or composite mixtures that allow you to withstand high static loads when you fish vertically. Quevertypes (replacement tops) in such models are often absent or have a very high test, since the visual registration of the bite does not occur by bending, but by tactile sensations in the hand or by nod.
Why not use regular short spinning?
Conventional short spinning (such as travel versions) have a parabolic long-range casting system, which falls under the weight of heavy bait in vertical fishing and prevents effective cut-off at a depth of 10+ meters.
It's important to note the handle design, which is often made of EVA materials or a finger-cut cork for a more robust grip in wet weather. Reeler usually screwed, with reliable fixation, excluding backlashes when active brush work.
Some models are equipped with an additional ring on the form just above the coil holder, which is done in order to ensure that when the fishing line is strongly stretched, the angle of its exit is optimal, preventing breakage of the first ring or the stick itself at the coll.
Selection criteria: test, structure and length
The best gear is based on the conditions of the reservoir and the fish species, and there is no universal solution, but there are clear parameters that should be used. The rod test The primary parameter that determines the weight of the goods used.
To catch a pike or a bearch at depths of 5-10 meters, you will need a test in the range of 20-60 grams. If you plan to hunt a pike or perch in standing water, the range shifts towards 5-25 grams.
The form must be fast or extra fast, which allows instantaneous pulse transmission when cut, and parabolic models are inefficient because they get stuck in the fish up and down. Length It is selected based on the growth of the fisherman and the height of the boat: for PVC boats, optimal models up to 1.6 m, for metal "Kazak" - up to 2.1 m.
When you choose, look at the bandwidths. They need to be reinforced, with a quality insert (SIC or Alconite), because the load on them is higher when you wiring vertically than when you wiring horizontally. Cheap ceramics will quickly be rubbed with a wicker.
Equipment: coils, lines and nods
The onboard fishing coil is a separate topic of discussion, with the ball being dominated by animators and high-traction non-inertial models. Multipliers It is preferable for heavy weights and deep places, as they do not turn the line and allow you to feel the slightest pokes of fish.
The main cord is used only wicker. Monophile stretches at depth, making the bite invisible, and fluorocarbon is too expensive to use as a base for large diameters. Writer cord with a diameter of 0.12-0.16 mm (Japanese classification #1.0-#1.5) is the gold standard.
And the nod is worth noting, because unlike winter fishing, the onboard nod has to be tougher and shorter, and its job is not only to signal a bite, but also to set the game to the bait. Often anglers use homemade structures made of springs or lausan plates.
| Parameter | For standing water. | For the flow | Universal option |
|---|---|---|---|
| Test (gr) | 5–25 | 20–60 | 10–40 |
| Length (m) | 1.2–1.6 | 1.6–2.1 | 1.6–1.8 |
| Cord (PE) | #0.6 – #1.0 | #1.2 – #2.0 | #1.0 – #1.2 |
| nod | Soft, long. | Hard, short. | Medium-severity |
The coil fittings must be resistant to corrosion. Salt water and sprays with dissolved sand particles quickly disable cheap machinery. Regular maintenance and lubrication after each fishing is mandatory.
Fishing tactics and wiring techniques
Fishing from the boat is very different from the shore, so there's no need for a long-range throw, the whole game is under the nose of the boat, and there are two main techniques: vertical flickering and jig in the plumb. Vertical flare It involves working with short swings of the rod, causing the bait to jump and plan.
Jig fishing in the plumb requires constant monitoring of the position of the bait at the bottom. The line must be stretched by a string. The bite often feels like a blow to the arm or a sharp "knock." The slashing should be short and sharp, with an amplitude of no more than 20-30 centimeters.
Use the sounder while you're fishing in plumb, and you'll see the fish's reaction to your game, and you'll be able to adjust the swing amplitude in real time.
Float drifting is a technique used in the current fishing, the boat is slow to swim in the wind or current, and the spinner catches promising points, and it's important not to cling to death if you're looking for an active predator, but to control the rate of demolition.
⚠️ Attention: When fishing in plumb never wind the line on your hand! With a sharp jerk of a large fish or a hook on a snag, this can lead to serious injuries to the hand or fingers.
The efficiency of the wiring depends on the rhythm. The predator often reacts to pauses. After a series of 3-5 strokes, be sure to stop, during which the bait slowly lowers, and it is at the fall that up to 70% of the pecking and bearsh occur.
Flight fishing baits
The range of the flight trooper is diverse, but it has its own specifications, and unlike the cast fishing, here the shape and play of the bait in vertical motion are more important than aerodynamics. Balancers They have a horizontal suspension, and when you wave, they go aside to describe the eight.
Vertical splashes (cloves, triangulars, pilkers) are also extremely effective, creating powerful vibrations and attracting fish from a long distance, and often using narrow, long lusters with a soldered hook or chain for perch.
- 🐟 Silicone baits: Vibrotails and twisters on jig heads or "Moscow montage" gear are ideal for passive fish.
- 🦑 Rattlin: Vibrating rappers without blades, creating a powerful background noise, provoking the predator to attack.
- 🪱 Dead fish: It's a big predator when other methods are powerless.
The color of the bait matters, but it's secondary to the game: in murky water, there's acid and white, in transparent water, there's natural tones. Size experiments are key to success. If a large balancer is ignored, switching to micro can have an unexpected result.
The secret to success is to constantly find a working bait, change the color, size and type of game every 10-15 minutes of unsuccessful fishing.
Safety and storage of gear
Boat fishing is always a risk. Short spinning is safer than long spinning because it's less likely to catch a neighbor or get entangled in gear when rolling, but sharp hooks and heavy loads require increased attention.
Storage of the rods should be organized so that they are not subjected to mechanical damage. Graphite is fragile on fracture. Use tubes or special cases with hard walls. Do not leave the gear in direct sunlight for a long time - ultraphirazet destroys the binder form.
☑️ Checklist for water safety
⚠️ Attention: Never leave your gear unattended on board on a sunny day. The heated elements of the coil and blank can deform, and the fishing line left in the sun will lose strength in one season.
After fishing, be sure to wash the gear with fresh water, especially if the fishing was conducted on salt water. The salt crystallizes in the mechanism of the coil and rings, causing corrosion and abrasive wear. Lubrication of the moving parts of the coil should be carried out regularly.
FAQ: Frequently asked questions
Can I catch a side spinning from the shore?
Technically, it's possible, but it's very inconvenient. A short rod will not allow you to throw long distances, which is critical in shallow water. In addition, the tests of flight crews are often sharpened to vertical loads, and when thrown "behind the back" the form may not work properly.
How long should the nod be for onboard fishing?
The optimal length of the working part of the nod is 10-20 cm Too long nod will sail strongly in the wind and create unnecessary fluctuations, knocking down the game of bait. The stiffness is selected under the weight of a particular bait.
Do you need a sip when fishing in the plumb?
When you fish vertically, you often go up to the boat and you see the boat and you jump to the side, and without the sucker, you're going to miss the trophy at your feet, and the length of the sucker handle should be the height of the board.
Why does the line at the coil break when fishing in the plumb?
Most often, the reason is "beards" or knots formed during previous casting or improper winding, and the line can be rubbed against the edge of the side of the boat or sharp edges of the holes (when fishing from ice, but the principle is similar). Always check the first 5-10 meters of the cord before fishing.