The organization of the working space on a boat is not just a matter of convenience, but a critical element of successful fishing. Holder for trolling on the boat It is a key element of the tooling, allowing you to effectively control up to 6-8 tackles simultaneously without the risk of overlapping and loss of trophies. A properly selected and installed mounting system turns chaotic fishing lines into a clear, well-functioning mechanism for catching a predator.
The modern market offers many solutions, from budget plastic glasses to complex engineering designs made of stainless steel with the ability to adjust the angle of inclination. The choice of a particular model depends on the type of vessel: whether it is lightweight. PVC heavy-handed aluminum-boatAn error in load calculations can cause expensive spinning to break or, worse, damage to the shipboard during a storm.
In this article, we will take a closer look at the nuances of selecting, installing and operating these devices, and learn how to properly distribute gear across the sides to ensure optimal wiring for wobblers, and what materials really withstand an aggressive salty environment. The maximum load per quality holder during trolling should not exceed 3-4 kg, even if the declared strength limit is higher.
Design features and types of fastenings
The fundamental difference lies in the method of installation and the purpose of the device. Airborne holder It's attached directly to the bumper or the transom, taking over the main traction of the fish and the resistance of the water when it moves. downriger or deck options serve to fix the tackle in a vertical position, often using additional outriggers for breeding fishing lines.
Manufacturing materials play a crucial role in the durability of the accessory. marine stainless steel AISI 316It's basically corrosion-free. aluminum-alloy or plastics require more careful care and regular lubrication of the moving elements to avoid jamming the angle adjustment mechanism.
Why is the angle of inclination important?
The angle of the holder's inclination (usually from 0 to 90 degrees) allows you to adjust the depth of the wobbler's immersion without changing the speed of the boat. The steep angle causes the bait to go deeper, the gentle angle reduces the entrapment.
It's important to consider the design of the glass itself. snap-mechanismIt's a slug-like device that allows you to instantly extract spinning when you bite without taking time to pull out of a deep glass. Other models are a slug tube, which is reliable, but less convenient when you're fishing.
- 🎣 Glass type: A classic solution where a spinning comet is inserted into a pipe and the form is pressed with a belt or a fixator.
- 🎣 With angle adjustment: Equipped with a rotary mechanism that allows you to change the angle of attack of the tackle depending on the depth and type of wobbler.
- 🎣 Universal platforms: Fixed to welding platforms or rails, allowing you to move the holder around the perimeter of the cockpit.
Specifics of installation on PVC and aluminum boats
Softboard installation PVC This requires a special approach, because classical drilling is not allowed here, and these vessels use special inflatable or rigid cans with integrated sockets, as well as belt mounting systems that cover cylinders, the main task is to distribute the load from the fish jerk so that the fabric of the side or seams is not damaged.
In the case of metal boat It's not the case with boats, and it's acceptable and often necessary to weld or mount bolts through the mandatory sealing through the through holes. Trans holders Aluminum is often combined with brackets for downrigers, creating a single powerful design on the stern.
When installing on PVC, use wide response slats (petaks) on the inside of the side if drilling is inevitable, which will increase the contact area and prevent tissue from breaking through under load.
Don't ignore the height of the setup. Too low will cause the wave to overwhelm the tackle, and too high will create excess leverage when catching, which can overturn the light boat. The optimal height of the glass slice above the water level is 40-60 cm.
For owners of inflatable boats are a great solution detachableThis allows you to quickly dismantle the equipment after fishing and transport the boat in its assembled form without unnecessary protruding parts.
Schemes of arrangement of tackles in trolling
The standard four tackle scheme involves placing two holders on the sides in the bow and two on the transom, which allows the wobblers to be driven at different distances and depths, simulating the movement of a pack of forage fish.
When increasing the number of tackles to 6-8 pieces, you need to use outrigger They allow you to spread the line to the sides, increasing the area of the area to be caught, the central gear goes behind the transom, and the side gear is much wider than the size of the boat.
It is important to keep the distance between the baits. Wobblears should not go in the kilvater stream of each other, unless it is a special tactical technique. Gliders And clips help to fix the line at the right distance from the side, but require accurate tension adjustment.
There's a "ladder rule" where the gear is arranged along the length of the vacation and the depth of the dive, and the spinnings near the boat are tuned to a smaller depth, the far ones are tuned to a greater depth, which minimizes the risk of overlap even with the sharp maneuvers of the vessel.
| Type of boat | Optimum number of tackles | Type of attachment | Recommended material |
|---|---|---|---|
| PVC (3.0 - 3.6 m) | 2-3 | Inflatable banks/belts | Plastic/Aluminum |
| PVC (3.8 - 4.5 m) | 4-5 | transom arc/Board | Stainless steel |
| Aluminum (4.0 - 5.0 m) | 4-6 | Welded glasses/rails | Stainless steel |
| Boat (5.0+ m) | 6-10 | Combined with outriggers | Marine steel AISI 316 |
Materials and corrosion protection
The aquatic environment, especially the salty environment, is extremely aggressive towards metals. stainless steel The 304 grade is only acceptable for freshwater and requires careful desalination after each fishing. AISI 316 (with the addition of molybdenum), which resists point corrosion.
Plastic elements, such as the sleeves inside the glass or the adjusting screws, must be made of ultraviolet-resistant polymers. Cheap plastic becomes brittle when exposed to the sun and can burst at the most inopportune moment, leaving you without gear.
⚠️ Warning: Even the best quality stainless steel requires maintenance. After each release, be sure to wash the holders with fresh water. The salt, drying on the metal, creates local corrosion centers that can destroy the structure in one season.
The attachment fittings (bolts, nuts, washers) must be identical to the material of the main holder. steel-holder Aluminum bolts, a galvanic pair will appear, and the fastener will rot in a few months, leaving the holder to hang on one or two surviving thread turns.
Instructions for self-assembly
The installation process begins with careful marking, and you need to determine not only the mounting point, but also the trajectory of the gear when you catch it, and the spinning should be able to leave the glass at any angle without touching the structure of the boat or other gear.
For cut-in models, a crown of the corresponding diameter is used in the side or trawler. The edges of the hole are necessarily treated with an anti-corrosion composition, and the glass itself is planted on a sealant (for example, polyurethane sealant), which provides watertightness and additional fixation.
☑️ Checklist before drilling
If you install the holder on the welding site, make sure that the weld is cleaned and painted. Immediately before tightening the bolts, apply a thread lock (for example, Loctite) so that the vibration of the engine does not weaken the attachments during the movement.
After you've installed it, do a test. Put the spinning in, simulate the jerk, check the locks, make sure that the structure doesn't have any backlashes that could cause the rod to break.
Exploitation and typical errors
One of the most common mistakes is to use too tight fixers, and if you hold the form "deadly", then when you bite a large predator or hook the spinning will not jump out of the hold, but break. Tension adjustment It should allow the angler to draw the rod with one confident upward movement.
The second common mistake is ignoring the length of the hanging line, and when the boat moves, the loose loop of the line can wind itself into a screw or get entangled in the boatmate's own gear. clippings Or keep the line in a strained state until you put it on the water.
⚠️ Warning: Never leave the tackle in the holders when moving on the planing unattended. A sudden stop or wave can throw the spinning overboard or, worse, confuse the fishing line in the screw, which threatens to lose the engine or damage the transom.
Check the condition of the rubber or plastic liners inside the glass regularly. If they are worn, the metal edge of the holder will begin to rub the lacquer coating of the form of your expensive spinning, which will lead to its dissection and breakage.
The main principle of operation: the holder must securely fix the tackle when moving, but allow instant extraction when pecking. Balance between rigidity and freedom is the key to success.
Frequently Asked Questions (FAQ)
Can I use car holders for fishing rods on a boat?
Car holders are not designed to be in constant contact with water, vibration from a water propeller and loads when catching fish, and their materials quickly degrade under the influence of UV radiation and salts, which will lead to the loss of gear.
What angle of tilt holder to choose for deep trolling?
For deep trolling (more than 5-7 meters), the holder is usually placed vertically (90 degrees) or even with a slight tilt towards the stern. This allows you to lower the wobler deeper by increasing the length of the line and changing the angle of attack of the bait relative to the bottom.
How often should the holders’ rotating mechanisms be lubricated?
At least once a season, preferably at the beginning and at the end, use only specialized lubricants for marine equipment (e.g., lithium-based or silicone) that are not washed away by water or destroy rubber seals.
Will the holder on a PVC boat withstand a pike weighing 10 kg?
A quality holder, properly mounted on a hard jar or reinforced side, will withstand the jerk of such a fish. However, it is critical that the design of the mount (belts, cans) is designed to handle such a load, otherwise the boat can get damaged.