Fishing on feeder It's not just a variation of coastal fishing, but a fundamentally different approach to capturing fish, requiring specific training and understanding of hydrodynamics. Unlike the shore, where anglers are limited by the range and bottom relief at the water's edge, the craft allows you to get to the cherished deep-sea breams, pits and dumps, where large breams, carp and carp roll in the summer heat or in high winds.
However, the use of feeder afloat has its nuances: there is no possibility to make a wide swing rod, and anchorage The wind and the current can turn comfortable fishing into chaos if you don't follow strict discipline and use the right installations, which is why many anglers, when they go from shore to boat, lose their catch at first, without understanding the reasons for the failure.
In this article, we'll look at everything from point selection and anchoring to catching, so that your fishing is not only efficient, but also safe. feeder preferably long, how to properly place the feeder relative to the hook on a strong current and what errors most often lead to cliffs.
Selection of the vessel and requirements for the anchor system
The first thing that a fisherman who is planning to fish from the water has to do is to choose the right boat. PVC boats with a hard or inflatable floor, as they have excellent stability and extinguish the jerks of fish better than a hard metal hull. Metal boats such as the Kazanka or Volzhanka are also applicable, but require more careful adjustment of gear due to high noise and less cushioning.
The key to success is the anchor system, and feeder fishing from a boat cannot use one anchor, because the boat will unfold with wind and current, which will lead to entanglement of gear. double-anchor This is a stern, nose, and aft that locks the craft in a strictly defined position with its nose or stern against the current, and it creates a stable platform for delicate feeder rigs.
⚠️ Attention! Never tie the anchor thack directly to the can or cylinder of the boat without a string-dragging. If you push hard or anchor, it can lead to the boat tipping over or damage to the cylinders. Always use the safety gear.
buyret.
For the fixation of the boat, it is best to use anchors such as Cat or Grapple, weighing from 3 to 5 kg, depending on the strength of the current and the sailing of the boat. It is important that the angle of separation of anchor ropes is at least 30-45 degrees, which will ensure the necessary rigidity of the structure even when changing the direction of the wind. electric-anchor It can make the process much easier, but requires a reliable power source.
Features of the choice of feeder rod for the boat
The main misconception of newcomers is to take the same long rods on the boat that they catch from the shore. Long blank (3.60-4.20 m) in the limited space of the boat turns from tool to problem: they easily catch on board, awnings or, worst of all, by anchor ropes. feeder length from 2.10 to 2.70 meters.
These rods, often called boat feeder Or just shorts, allow you to perform accurate casting even sitting, without getting up from the seat. The rod test should match the weight of the feeders used, but it should be borne in mind that the boat often has to catch on a strong current, where heavy feeders weighing 80-120 grams or more are required.quivert) will allow the bite to be clearly seen and the fish to be controlled with confidence.
The coil must be reliable, with good traction and a volume of a spoole of 4000-5000 according to the Shimano classification. 4.6:1 – 5.0:1Because high-speed coils are less effective at pumping fish from depths and working with heavy feeders, having a bytranner or free-route coil flag is desirable, but not critical if the angler is closely watching the gear.
When choosing a boat rod, pay attention to the length of the handle: too long a handle will rest on the side or interfere with the catching, the optimal length is up to 30-35 cm.
Search for a promising place and anchoring tactics
The success of feeder fishing from a boat depends 90 percent on the right point. While you're on shore, you can only guess where the brow is. On a boat, you have the advantage of using the right point. sounder Your goal is to find a sharp drop in depth, an exit from a pit, or a local elevation at the depth.
The way you search is you slowly drift across the intended direction of the current, watching the sounder readings. As soon as there is a sharp jump in depth on the screen, for example, from 4 to 6 meters, this place should be "remembered." To fix the point, use a GPS navigation device, save the coordinates, or attach a buoy marker if the current allows.
How to read a feeder sonar
Look not just for depth, but for structure. A flat plateau without gradients is a bad sign. You want steps where white fish can feed and a predator or a large bream can wait for prey. Also, look for driftwoods or rocks, which are visible as arcs or intermittent lines on the screen.
Once you find the point, you anchor. You go upstream from the chosen location (10-15 meters, depending on the depth and the flow strength). Give the stern anchor, you snag the rope until you reach the point, then you give the bow anchor. You pull both ropes, you lock the boat. It's important that the gear is hanged vertically or at a slight angle, but not on the bottom far away from the boat, otherwise you lose sensitivity to pecks.
Installation and equipment for fishing from a boat
The configuration of the equipment when fishing from a boat has its own specifications, dictated by the vertical or close to the vertical position of the tackle. Gardner loop or Running FeederThey work perfectly, but there are nuances in the length of the leashes. In strong currents, when the line is under high flow pressure, the leash should be made shorter than in coastal fishing - usually 30-50 cm.
If the current is moderate, you can use longer leashes (up to 80 cm) to make the nozzle play more natural. Choose hooks depending on the type of nozzle: for worm and worm, long forearm models will suit (for example, Owner 53117 or Mustad 3399), and for corn and hammers - with a round bend and a short forearm. The thickness of the leash line varies from 0.10 to 0.16 mm, but when catching trophy carp or carp, it is better to be safe and put 0.18-0.20 mm fluorocarbon.
☑️ Checking the equipment before throwing
Special attention is given to feeders. For boat fishing, bullet feeders with soiling hooks that hold the bottom well, or classic metal nets, plastic feeders can pop up when lifting, which is sometimes convenient, but can bear them when strong, the weight of the feeder is selected experimentally: it must lie confidently on the bottom, but when cut off, do not drag on the bottom, but immediately break off.
Feeding technique and the fishing process
Boat feeding is very different from shore feeding, and you don't have to feed a point with balls or a slingshot because you're directly above it. Start feeding is done with a series of 5 to 10 quick throws of a full feeder, and it's important that the feeding is washed out in 2-3 minutes, creating a vertical muti table that attracts fish.
When you fish, the rate of re-fishing is dictated by the activity of the fish and the strength of the current. If it bites actively, re-fishing is done often to keep the concentration of the feed at a point. If there are no bites, the intervals increase to 5-7 minutes. lazy feederWhen the feeder after falling to the bottom is slightly pulled up to begin to tear the food, creating a plume.
| fish-fish | catching horizon | Typical nozzle | Weight of the feeder |
|---|---|---|---|
| Breeze | Done | Worm, squirrel, pellets. | 60-100 g |
| Sazan/Karp | Bottom/bottom | Corn, boyls, worms. | 80-120 g |
| Iaz | In the waters/At the bottom | Bread, bread, dough. | 40-80 g |
| Sudak | Done | Cut, worm, bait. | 60-100 g |
It is important to monitor the behavior of the top. On a boat, especially in the wind, the nod can shake with the vibration of the hull. A real peck usually looks like a confident bend or, conversely, a relaxation of tension (if the fish goes to the angler), the slash should be short and sharp, since the distance to the fish is minimal, and an extra sample of slack foliage (slack) is not required here.
Recovery and safety on the water
Removing a trophy from a boat is always a stress test for the nervous system and equipment. The main rule is: never twist the handle of the coil when the fish resists and pulls the line. Give it freedom of movement by lowering the rod to the water, and wait for the moment when the jerks stop. sucker You need to take the fish strictly from the head, so that it does not get scared and does not leave at the last minute.
The boat itself is a danger. Big fish, when they get into the water under the boat, can start to throw themselves and get the fishing line tangled by the anchor ropes or the engine screw. To avoid this, try to immediately after the cut, take the fish away from the projection of the boat, working as a rod. If the fish still went under the boat, do not pull it vertically upwards, you better slowly release the rod so that it comes out on the other side, and only then continue to catch.
⚠️ Attention! When fishing for large fish (sarzan, large carp), always keep a knife on hand. If the line winds up on the leg or gets tangled in the equipment of the boat, and the fish makes a jerk, the count will go for seconds. The knife must be in an easily accessible place, preferably on the belt or tied to the vest.
Keep your personal safety in mind, too. Fishing, especially when standing or actively fishing, increases the risk of losing balance. A life jacket is not just a formality, it's a necessity, especially if you're fishing alone. Even an experienced angler can't resist the slippery, water-drenched floor of a boat when a trophy snags.
Water safety is more important than catching: never neglect a life jacket and always have a knife on hand to cut the line.
Frequent mistakes and how to avoid them
One of the most common mistakes is choosing the wrong length of the anchor ropes: if the ropes are too short, the boat will constantly twitch on the wave, which will alert the fish. If too long, the boat will turn across the current, which will create inconvenience for throwing and catching. The optimal length is 3-4 depths at the point of fishing.
The second mistake is to use too rough tools, and fishermen who are used to coastal fishing often put leashes of 0.25 mm or thicker, citing the possibility of catching trophies, but in clear water and with bad sticks, the fish sees the fishing line and ignores the nozzle. For bream and carp on pressed water bodies, it is critically important to use leashes thinner than 0.14 mmEven if there is a risk of a cliff.
The third mistake is feeding, and many people try to feed the dot with a lot of stuff, thinking it's going to attract more fish, and in fact, a lot of feeding feeds the fish, and it stops responding to the nozzle, and the "often but little" principle works much more efficiently from a boat.
What should I do if the boat starts to turn around?
If the boat is turned across the current, do not try to row or pull anchor. First select one anchor rope (usually the one that is against the current), move the anchor upstream and anchor again, then repeat the procedure with the second rope.
Do I need to use a sonar for feeder fishing from a boat?
The sounder is not strictly mandatory, but it's highly desirable, it allows you to not guess, but to know exactly the bottom relief, find eyebrows, pits and even fish clusters, without the sounder, you catch blind, relying only on intuition and knowledge of the reservoir.
Which line is better to choose: a wicker or a monophile?
For a boat feeder, preferable thread-cordIt's not stretchable, which gives you great sensitivity at great depths and allows you to make sure you cut it, and the monophilic line is stretched, which "greases" the bite, especially at depths over 4-5 meters.
Can I catch a feeder from an inflatable boat without a motor?
Yes, you can. A rowboat is even more convenient for quiet and tidy fishing, because there is no motor noise that can scare the fish, but you will have to deliver the gear and anchors on oars or by drag, which requires more physical effort.
Why does the line break when you get off the boat?
A common cause is the sharp edge of the boat or the shell on the anchor rope, which rubs the line, and the reason can also be the wrong setting of the friction: if it is tightened too much, the jerk of a large fish will lead to a cliff.