Many fishermen still believe that the classic bottom-handle With a rubber shock absorber, it is only effective when fishing on the shore, when the cargo is thrown from land. However, experience shows that fishing from a swimming aid opens up completely new horizons for the milker. snagThe brows overgrown with grass and deep pits, where it is simply impossible to take the cargo from the shore or bring it by boat without the risk of hooking.
The main advantage of this approach is the possibility precision delivery It's a pre-selected point, which is critical when hunting for a pike or bream tied to a particular bottom relief, and it removes range constraints and allows you to work with thinner fishing lines, because there's no need for a powerful jerk when you start throwing, which makes the tackle more delicate and catchy, especially during periods of passive sticking.
You don't have to have a very expensive boat to practice this method. PVC It's important to understand the specifics of the installation and sampling of the gear, so as not to confuse the fishing line and lose load. In this article, we will discuss in detail all the nuances, from the assembly of tooling to the tactics of finding fish in the reservoir.
Benefits of fishing with a swimming means
The shift to fishing from a boat is a radical shift in the way we approach fishing to bottom tackle. perfect-track From the shore of the line, it often lies down in an arc, bending irregularities, which makes it difficult to cut and creates sailing on the current. From the boat, you can set the gear strictly perpendicular to the shore or along the brow, which greatly improves contact with the bait.
And also, using a boat allows you to change your dislocation quickly, and if you don't have a cooler in an hour, you're not tied to one place, you can quickly pick out a tackle, swim a few meters further, and recharge your gum, and that mobility is especially valuable when you're looking for it. migratory fish in large reservoirs or rivers with strong currents.
Another important aspect is the possibility of using longer work sites, so as long as the shore angler is limited by the length of the loader's throw, the boater can sail as far as he wants, providing a comfortable area for the placement of 10, 15 or more hooks, which turns the donck into a real fixed net, which, however, does not violate the rules of amateur fishing, as it is an active tackle.
Design and features of gear for the boat
Although the principle of operation remains the same, the design rubber There are different things about boat fishing, especially the length ratio of rubber shock absorbers to fishing lines, and for shore fishing, you often use a 1:3 or 1:4 stretch factor to get the load, and when you're working from a boat that's hand-delivered, you can reduce that to 1:2 or even 1:1.5.
Reducing the coefficient of stretching allows you to use more rubberIt's a snail that sails less in the course and returns the hooks to their starting position faster after cutting, and it's critical for fishing at depths of over 4 meters, where soft rubber can take a long time to walk underwater, confusing leashes.
Special attention should be paid to the fastening of the cargo. Since you will be lifting it by hand, the weight of the cargo can be any, but it is better to use loads with an eye or tie the fishing line to the center of gravity, so that when sampling it does not cling to bottom obstacles.
For installation of the main line is best used cock-cord Or a line with a diameter of 0.4 mm. Thin lines when sampled from a boat can cut fingers, and if there are hooks, they are easier to break if the main cord is strong. The lead is set with a length of 15-25 cm, so that when sampled they do not overwhelm the main line.
Preparation and installation of gear
The installation process begins with careful preparation. On the shore or in the boat, you need to unwind the main cord, check the rubber condition for cracks and straighten the leash. The hooks are better equipped with a nozzle in advance, so as not to waste time on the water. If you fish alone, the installation process requires a certain skill and sequence of actions.
☑️ Checklist before installation
First, the boat is anchored upstream from the intended fishing site, the cargo with the rubber band and fishing line is carefully placed on board or in a separate container, so as not to get confused at launch, the boat slowly moves downstream or sails away until the cargo is lowered at the desired point.
⚠️ Attention: Never tie the end of a rubber band to the side of a boat or to an anchor shaft! With a strong fish jerk or a sharp gust of wind, rubber can pull the boat off anchor or, worse, get tangled in the engine propeller if it is lowered. The end of the tackle must be securely fixed to a separate anchor ring or holder inside the boat.
Once the load has been laid down, you have to choose the slack of the main line, but leave the rubber in a slightly strained state. The line is laid in water or on special motovils. ionMake sure the brake friction is released so that the fish can reel off the fishing line when biting.
Search tactics and location selection
And the success of fishing for rubber from a boat depends 80 percent on the right location. Unlike shore fishing, where we're tied to the accessible shore, here we can find any bottom anomaly. pit-holeThe boundaries of the shell and the sand tongues, extending into the depths.
The tables, the plateau-like highlands in the middle of the depths, are very effective, and the bream and the pike like to go out to feed on these areas, and to find them, use a sonar or a method of measuring the depths of lead weights on a cord with markings, and when you find a difference in depth, anchor upstream and throw the load on the lower eyebrow.
When fishing on the current, it is important to consider the removal of the fishing line. The equipment should lie at the bottom at an angle, forming an arc. If you put the boat strictly above the load, the fishing line will hang in the water column, which will lead to frequent overlapping and false bites from the little things that swim by, the optimal angle between the fishing line and the bottom is 30-45 degrees.
Secret tactics for night fishing
At night, predators and white fish often go out into shallow water, and set a rubber band across the brow so that one edge of the tackle is 3-4 meters deep and the other goes 1.5 meters deep, and this allows you to simultaneously catch a bream at the depth and a perch or pike at the dump.
Fishing and hooking techniques
The boat tackle has its own specifics: the cutoff has to be sharp, but not overly sweeping, so as not to pull the hooks far out of the fishing zone. Thanks to the elasticity of the rubber, after the cut, the hooks will come back to their place. Your task is to choose a line, remove the fish, correct or replace the nozzle and smoothly release the gear.
Fishing on the current often uses the "game" technique. Once you have the gear, you can periodically smoothly pull the fishing line up to 10-20 cm and let it go. This movement makes the bait move, which provokes the predator (perch, perch) and attracts the attention of the white fish, but you need to do this carefully so as not to confuse the leashes.
The number of hooks varies from 5 to 15. For fishing from a boat, it is optimal to have 7-10 hooks. The greater number makes it difficult to maintain the tackle, especially in windy weather or when active pecking when the fish begins to get confused. The distance between the hooks should be at least 1.5-2 leash lengths so that the neighbors do not catch each other.
| fish-fish | № hooks (in Russian Federation) | Type of nozzle | Depth of fishing |
|---|---|---|---|
| Breeze | 8-10 | Worm, squirrel, corn | 3-8 meters |
| Sudak | 6-8 | Malek, cutting, worm | 4-10 meters |
| Carp | 10-12 | Dough, worm, barley. | 1-4 meters |
| Perch | 8-10 | Worm, baby. | 2-6 meters |
Boil and fish
spol