Solo fishing nets from a boat are a top-of-the-line fishing skill that requires not only physical endurance, but also a deep understanding of the hydrodynamics and habits of the fish. Many beginners mistakenly believe that they will be able to perform a sea-going fishing mission. net It is impossible to do it alone, but with proper preparation and the availability of suitable equipment, this process becomes quite manageable and even debugged to automatism.
The main difficulty is the need to simultaneously control the movement of the boat, monitor the purity piecework and stack properly load-cordUnlike working in pairs, where one person rows or drives the engine and the other one runs the network, a single person must perform all these functions in synchrony, relying on pre-prepared mechanisms and the inertia of the boat.
The success of the operation depends on the choice of gear and the conditions of the reservoir, so before getting on the water, you need to soberly assess your strength and capabilities. PVC boats A well-organized workplace and safety knowledge will turn a complex task into a routine but fascinating procedure that can bring impressive catches.
Selection of the place and analysis of the conditions of the reservoir
The first and perhaps most critical step is to choose a place to install fishing gear, because it depends not only on the catch, but also on the safety of the fisherman. On lakes with variable depth and complex bottom relief, installing a net alone can become a real torture if you can find yourself in a situation where you can find yourself in a lake with varying depths and complex bottom relief. load-cord will catch on the snag or bottom vegetation, which will lead to entanglement of the entire canvas.
The direction of wind and current must be considered, as these are the factors that will dictate the boat's trajectory during the tackle sampling. If you plan to put the net across the brow or along the reed thickets, make sure you have the maneuverability and that you can do it. net It will not be blown by the wind to the already established areas or to the boat itself.
⚠️ Warning: Never try to set nets alone in high-current areas or in open water during a storm warning, as the risk of getting tangled in your own gear or flipping the boat increases many times over.
For successful fishing, it is important to understand the structure of the bottom, so preliminary depth-test If you know the terrain, you can choose the optimal length of the network and the type of equipment, which is especially important when working without a partner, when correcting errors takes a long time.
- 🌊 Evaluate the direction and strength of the wind so that it helps rather than hinders the boat’s movement.
- 🌿 Avoid areas with abundant bottom vegetation that can “eat” the net.
- 🗺️ Examine the depth map or use the sonar to look for eyebrows and pits.
- 🚫 Check the lack of shipping lanes so as not to become a hindrance to other boats.
Preparation of equipment and equipment for single work
The quality of the equipment before getting on the water determines 90% of the success of the entire operation, especially when you work without the help of a partner. tape or to the bunker so that when sampled it comes out freely, without jerks and hooks, which is critical to maintain integrity piecework.
Particular attention should be paid to the network: load-cord must be heavier than usual to ensure rapid immersion of the tackle, and float-cord It should be buoyant enough to keep the net upright, and for single-handed operation, networks with increased mesh pitch and reinforced landing are ideal, which are less prone to entanglement.
Equally important is the preparation of the boat itself: you need to secure all the moving elements so that they do not interfere with the work with the network, and prepare special hooks or leera for temporary attachment of the gear. cat anchor With buoy-buoys (float markers) attached to them, it will make it easy to find the ends of the network after installation.
To make it easier to sample the network, you can use special mechanical or electrical grid winches that are attached to the boat, but even without them, using the right stacking technique and simple devices like this. rogue For temporary storage of the selected network, you can achieve excellent results.
- 🎣 Check the integrity of the workpiece for tears and holes before exiting.
- ⚓ Prepare additional anchors and buoys to mark the ends of the network.
- 🧤 Have spare kits for boats and nets on hand in case of unforeseen situations.
- 🔦 Don’t forget to use the lights and lights if you plan to work at night.
Network installation technique: step-by-step algorithm of actions
The network installation process begins when the boat is in a starting position against wind or current, allowing the vessel to control drift. load-coreHe made sure he went underwater and began to straighten out, forming the right wall.
Moving at low speed or working with oars, you need to give the network evenly, controlling that the float-cord not over-swept with load-coreThe main rule of a solo is to constantly monitor the back of the boat, as this is where the net goes into the water, and any sudden movement can lead to its entanglement in the engine propeller or on oars.
☑️ Checklist before installation
Done: 0 / 5If you're using a motor, you have to be at a minimum speed, literally at idle speed, so that the net can spread and sink, and in calm weather, you can use the inertia of the boat, giving it a short acceleration with paddles, and then giving the net off during the free passage of the vessel.
⚠️ Attention: It is strictly forbidden to try to unravel the network, if it caught on the screw of the working engine - turn off the engine and only after a complete stop of the screw proceed to release the gear.
The final step is to anchor or buoy at the ends of the network, which should be brightly colored and visible from afar. A properly installed network looks like a flat wall, facing underwater, without sagging and hinges on the surface.
Table: Comparison of methods of network installation alone
To systematize knowledge and choose the optimal strategy, it is worth considering the basic methods of network installation available to solo fisherman and their specifications in different conditions.
Method of installation Equipment required Complexity Risk of confusion Anchored (static) Two anchors, buoys Low. Minimum On the move (with the engine) outboard motor, winch Medium Medium (screw) On paddles (quiet move) Oars, tape for the net. High. Low. From a drifting boat. Sail or wind drift Medium High (demolition) The choice of method depends on the specific conditions: in shallow waters or in overgrown areas, it is better to use the method of installation from anchor, working carefully with oars, so as not to damage the network. In deep water and with experience, you can use the motor efficiently, which greatly speeds up the process.
5 to 3 meters, since at great depths to control the verticality of the canvas alone becomes extremely difficult without specialized equipment.
Network sampling and catching process
Network sampling is the most time-consuming stage that requires maximum concentration, since it is at this point that the risk of getting confused is high. flat-paint The movement must be strictly against the wind or current, so that the net is placed on board, rather than being pulled under the boat, creating dangerous stress.
Gradually pulling up load-cord and float-cordYou need to carefully choose the fish, freeing the gills and fins, and immediately put the catch in a special container or on the kukan, so that it does not interfere with further work. loader They didn't crash on board.
What to do if the network gets confused?
If the network is entangled, do not pull it sharply. Dip the entangled area carefully in water, straighten the knot underwater where del slides better, and only then continue sampling. In critical cases, use a knife, but try to maintain the integrity of the canvas.
When sampling a large network alone, it is useful to use special hooks on a long handle or even homemade "racks" for pull-ups. cargo-cordThis is especially true for owners of narrow boats, so as not to bend over the side and not to disturb the balance of the boat. PVC boatswhere any shift in the center of gravity can cause a roll.
- 🐟 Check every meter of the net for stuck fish to avoid missing the catch.
- 🧶 Distangle small nodes immediately so that they do not turn into large tangles.
- 💧 Rinse the net in water periodically to wash away the mucus and mucus, making it easier to sample.
- 🛑 In high winds, stop sampling and wait or secure the net on buoys.
Security measures and typical novice errors
Safety on the water is the number one priority, especially when dealing with networks that can cause serious injuries or loss of a boat. The main mistake of beginners is neglecting the life jacket and trying to work in an unstable boat, which, combined with entanglement in the network, can lead to fatal consequences.
A common problem is misjudged weather conditions: the wind can quickly intensify and the boat with the half-net will begin to carry on obstacles or open water. Always carry a sharp knife mounted on the belt or on the strap of the vest, so that at any time you can cut. load-cord Or tangled tackles.
Always bring a spare set of anchors and buoys, as losing one of the items can make it impossible to find a network, especially on a large body of water.
Another common mistake is to set up networks that are too long alone, which is physically difficult and technically difficult to control, and it is better to put two short nets than to suffer from one huge one, risking spoiling the tackle and losing the catch.
The main principle of safety: the network should not become an anchor for your boat, always leave the opportunity to quickly release the gear in an emergency.
Don’t forget about the legal aspects: make sure that the size of the mesh, the length of the net and the installation site are in compliance with the fishing regulations for your area to avoid fines and confiscation of equipment.
Can I put a network on a strong current?
It is strongly advised not to put the net alone on a strong current, since control of the boat and gear will be almost impossible. The network can instantly become confused, and the boat will turn across the current, which will create an emergency situation.
What is the optimal length of net for solo fishing?
For single fishing, the optimal net length is 25 to 50 meters. Longer nets (100 meters and above) require a second person to control the installation and sampling process.
Do I need to register a network in GIMS?
Yes, according to the legislation of the Russian Federation, all fishing gear, including nets, must be marked and entered in the travel list or permits if fishing is carried out in permitted places and seasons.
What if the network is broken during the sample?
If the network is broken, you need to carefully collect both ends, link them with a time node and continue sampling, and at home the damaged area will need to be patched or replaced with delya.