The windy weather on the lake turns simple fishing into a test of strength and nerves of the crew. flyboat It's not fixed reliably, and gusts of wind can turn the side perpendicular to the wave, which will lead to a dangerous roll and even a flip. Unlike a heavy Kazanka, a light PVC vessel has a high sailing speed, so you can't ignore the force of the elements.
Proper anchorage requires understanding the physics of the process and understanding the features of the bottom relief. Mistakes in choosing a place or method of attachment often lead to a break in the falt or loss of anchor. We will discuss proven techniques that will help you maintain your position even in storm gusts.
Features of anchoring inflatable vessels
The main problem with light boats is that they're lightweight and they have a lot of surface area. sidewindThe boat starts to demolish quickly, and the anchor rope is pulled at a sharp angle, which creates the risk that the anchor will simply pull out of the ground, preventing it from catching.
For reliable fixation, you need to take into account sailability And the higher the center of gravity, the stronger the sway, and the more heavy the anchor can be dangerous for an inflatable balloon when you snatch.
If the falt is rubbed or has knots, it can damage the fabric under heavy tension. Always use smooth-surfaced carbines and check the condition of the ropes before leaving.
Use a special case made of dense fabric on the bow of the boat, if you plan to anchor often in windy weather - this will protect PVC from rubbing with the phalt.
Choice of anchor and phalanx
For inflatable lake fishing, cat anchors weighing 3-5 kg are ideal. Their paws are easy to fold, saving space and weight enough to keep the boat in moderation. Heavy models can be redundant and dangerous when climbing on board in pitching conditions.
It is better to use as an anchor rope polycore They have a certain elasticity that dampens the boat's thrusts on the wave, reducing the load on the anchorage points, and steel cable is not recommended because of its rigidity and the risk of damage to cylinders.
- 🪢 Length of the falter It should be at least 3-4 depths in the parking area to ensure the correct angle of attack of the anchor paws.
- 🧶 Nylon cord preferable polypropylene, as it is less stretched under load and resistant to ultraviolet light.
- ⚓ Anchor rum It must be installed strictly according to the diameter of the boat and have a reliable attachment to the transom plate or bottom stringer.
Pay special attention to the mounting point. On many budget models. pyre They're only glued to the top of the fabric, and in high winds, the load can tear them off, and make sure that your anchor shaft is attached to a power element, like a leer, that runs along the side.
Why not use a chain instead of a rope?
The chain has a huge weight that can damage an inflatable balloon when rocking a boat, and the chain does not extinguish the jerks, transferring all the energy of the impact to the mounting points, which leads to their rapid destruction.
Definition of location and direction of drift
Before you anchor, you need to assess the situation. Stand in the drift and see where you are blowing. The wind on the lake often blows unevenly, creating swirls near the shore. Your task is to stand up so that the boat turns nose-on to the wind and wave.
If you stand up wave-sideThis will increase the pitching amplitude, not only causing seasickness, but also creating a risk of water flooding through the side, and proper orientation is the key to a comfortable and safe parking lot.
| Factor. | Impact on the boat | Recommended action |
|---|---|---|
| Strong wind | Demolition, roll-around | Stand up against the wind |
| Current | Shift of position | Use two anchors |
| Bottom relief | Bad anchor hook. | Pick a place with silt or grass |
| Excitement | Twisting the falt | Increase the length of the anchor end |
And look at the surroundings, and the trees on the shore can create wind shadow zones where the wind subsides, but there can be dangerous swirls right behind them, and the open water is safer, but the wind flow is more stable and predictable.
☑️ Checking before anchoring
Installation technique: one and two anchors
The most common method is to place one anchor from the nose. When you get to a point, you pit the pellet slowly, let the anchor touch the bottom. Then slowly back up, picking the slack until the anchor is buried. The sharp jerks when you throw often cause the anchor to fall down with its paws up.
In a strong wind, the scheme is effective.floppyIf depth permits, reduce the length of the anchor line, which will reduce the radius of the boat's circulation around the dock and reduce the yaw amplitude, but the angle of attack of the paws must remain sharp.
⚠️ Attention: Never tie the anchor tile tightly to the rim without the possibility of a quick release. In the event of a sudden squall or the need to leave urgently, you should be able to uncoup instantly.
If the wind is blowing in different directions or you are swinging heavily on the wave, use a two-anchor circuit, one is mounted from the nose, the other from the stern, this locks the boat in a strictly defined position, except for turns. feed-fish.
When placing a second anchor from the stern, it is important not to confuse the shafts, they must come from different ends of the boat and not intersect under the bottom, a scheme often used for fishing in plumbing or jig, when you need to rigidly fix the position.
The use of two anchors (from the nose and stern) is the only way to completely eliminate the turn of the boat side to wave in variable wind.
Correct knots and anchorages
The reliability of the entire system depends on the nodes.baleenIt doesn't tighten tightly under load, and it's easy to untie even after standing in the water for a long time.
Carbine is often used to connect the rope to the anchor ring, but the knot is more reliable, since the metal can corrode or spontaneously open from vibration. If you use a carbine, choose models with double or triple locking.
- 🪢 Node Eight. At the end of the phallus, it will prevent it from slipping through the ear of the anchor or the river.
- 🔪 Knife should be fixed on the boat in an accessible place, preferably on the belt or in a special pocket near the seat.
- 🧵 Grabbing knot It is useful if you need to temporarily fix the tension of the fala on the leera without using a duck.
Check the condition of the ropes for scuffs. The sun and salt make the synthetics brittle. If you notice the filament filament, it's better to replace it. In an emergency, it may not be able to withstand the full weight of the boat in the wind.
Typical errors and security measures
One of the most serious mistakes is to tie the faucet to seat In high winds, the load can reach hundreds of kilograms, and the weak attachment will be pulled out along with a piece of cylinder or bulkhead. Use only regular metal dice.
Another mistake is that the thalf is not long enough, and if you anchor at a depth of 3 meters, with only 4 meters of rope, it will lie on the bottom, but it will not catch. The paws must lie on the ground and burrow, and for that you need a gentle angle.
⚠️ Attention: It is strictly forbidden to wind an anchor tile around the arm or body, and if a boat jerks sharply, the rope can cause serious injuries, break bones or drag a person overboard.
Always have a plan B. If the anchor is dead in a snag or a rock, and the wind is getting stronger, you should be able to shoot the anchor. To do this, a thin safety rope (buoys) is tied to the anchor ring, or special safety ropes are used to reach the surface. break-off.
What if the anchor is stuck?
Don't pull the boat forward, it can damage the transom. Try to approach the anchor from different sides, picking out the slack of the fail. If it doesn't work, use a snatcher or buoy.
FAQ: Frequently asked questions
What is the optimal weight for a 3.2 meter long boat?
For a PVC boat with a length of 3.2 meters, an anchor weighing 3-4 kg is considered optimal. The heavier (5 kg) can be used on the current, but it is harder to lift by hand, especially if the legs are stuck. Light anchors (1-2 kg) will be ineffective in winds of more than 5 m / s.
Can I use an anchor box instead of a classic anchor?
Yes, an anchor box (Danforth's box or a homemade box of stones) is a great alternative for a muddy bottom, it works like a suction cup, but on a rocky bottom, its effectiveness drops, and it can just slide on the surface.
How to safely raise the anchor in a strong wave?
You have to lift the anchor slowly, picking the throttle with your hands, not with the jerks of the motor. If the anchor is set, come close to it, select a slack and fix the throttle. Then slowly move to the opposite direction of the ambush, using the short work of the motor to shake the anchor.
Do I need to shut down the engine when I am at anchor?
In high winds, it is not recommended to completely silence the engine if you are away from shore, it is better to leave it at low speeds or in trolling mode so that you can instantly add traction for maneuvering or avoiding danger.