The organization of the space on a swimming vehicle is not just a matter of comfort, but a critical element of safety and efficiency of fishing. When a slippery, vibrating balloon underfoot, unnecessary movements become dangerous. spinner It is one of the first elements of tuning, which is thought of by an experienced angler.
Unlike metal or fiberglass boats, inflatable boats require a special approach to fitting any accessories. You can't just drill a hole or weld a structural element. It's about adaptability and material care. Mistakes in fixing can lead to the loss of an expensive rod or, worse, damage to the balloon and depressurization of the boat on the water.
The modern market offers many solutions, from simple plastic clips to complex systems with rotary mechanisms and built-in organizers. The choice depends on the type of catch, the number of tackles and the design features of your boat. In this article, we will discuss all aspects of the choice in detail, compare popular models and provide step-by-step installation instructions that will help you avoid typical mistakes.
Typology of holders: from simple clips to rotary systems
The first thing that an angler encounters when looking for an accessory is a huge variety of designs. The basic solution is a simple plastic clip that sticks to the cylinder. It's lightweight, cheap, doesn't require complex installation. But its functionality is limited: it just keeps the rod in a horizontal position, often without providing reliable fixation when large fish jerk or pitch.
A more advanced option is the holders with adjustable angle of inclination, which allows you to adjust the position of the form so that the line does not get confused overboard or the trawler. turning-pieceThese are the ones that are attached to the nozzles or special platforms, and these devices allow you to quickly change the catch sector without getting up, which is especially true when you're trolling or drifting.
- 🎣 Balloon clips Minimalism and lightness, ideal for storing spare gear.
- ⚓ Trans holders - rigid fixation on the stern, often used to install additional fishing rods when trolling.
- 🔄 Turning bases Maximum comfort, allow you to change the direction of the rod by 360 degrees.
When choosing the type of attachment, it is important to consider the diameter of the comet of your spinning. Universal models often have rubber liners or adjustable clamps. If you plan to use heavy rods with a test above 60 grams, you can not save on the material of the holder’s manufacture – stainless steel or reinforced plastic is preferable.
⚠️ Attention: Cheap plastic holders become brittle in the cold. If you plan to fish in the off-season, make sure the accessory material retains elasticity at low temperatures, or it can burst at the first spurt of the fish.
Ergonomics should also be avoided: the holder should be positioned so that you can take the rod without hindrance, even if you are wearing a voluminous life jacket or raincoat, and the shifting of the center of gravity when installing heavy metal structures also plays a role, especially on small inflatable boats, where every hundred grams is important.
Methods of installation: glue and glueless solutions
Boat owners from PVC (PVC) often fluctuates between wanting to secure equipment and fear of damaging the tank material, and there are two main ways to do this: using glue or mechanical clamps, and the adhesive method is considered the most reliable and durable, but it requires preparation and accuracy.
For installation on adhesive, special two-component polyurethane-based compounds or specialized adhesives for PVC are used, such as Texacol or RadicalImportantly, the adhesive pad (pet) is made of the same material as the boat itself, or of a compatible material with a similar density, which ensures the monolithicity of the joint that withstands high tear and shear loads.
Glueless methods are becoming increasingly popular because of their safety and reversibility, including attachments to the clamps on board (with soft sponges), and suction cup systems, which are only suitable for smooth, hard surfaces and inflatable boats often prove useless due to the curvature of cylinders and ribbed fabric structure.
Mechanical clamps covering the cylinder should have wide soft pads. Narrow rigid clamps can damage the protective layer of tissue with prolonged exposure or vibration. If you choose the option with a mount on the switch, make sure that the diameter of the hole in the holder corresponds to the diameter of your key, otherwise the design will backfire.
☑️ Pre-installing check
There are also combined options, where the platform is glued, and the holder is inserted into it by the type of bayonet connection. Lock & LoadThis allows you to quickly remove equipment when you don't need it, leaving only a neat platform on the tank, an approach that is optimal for those who use the boat not only for fishing, but also for family walks.
Instructions: how to properly glue the platform under the holder
If you're stuck with the glue method, which guarantees maximum reliability, you have to follow the technology very closely. If you break the temperature or dry time, you'll have your site peel off with the holder and possibly the spinning, and it takes patience and cleanliness.
First, you have to prepare the surface carefully. The place on the tank where the nickel will stick, you have to wash with soap, dry and degrease. The best way to degrease is to use pure alcohol or a special degreasing agent, but not acetone, which can damage some types of PVC. After that, the surface should be skinned with fine sandpaper for better adhesion.
The technology may vary depending on the brand of the composition: some require the application of one layer on both surfaces and immediate connection, others require the application of two layers with intermediate drying and subsequent heating with a hairdryer. Carefully read the instructions on the tube. polyurethane Often, activation of the adhesive layer with hot air is required.
| Work segment | Time/Temperature | Key action |
|---|---|---|
| Preparation | 20-30 minutes | Cleaning, drying, degreasing |
| Applying glue | Depends on the type. | Uniform layer with brush |
| Drying the layer | 15-20 minutes | Before the stickiness disappears |
| Sticking | Instantly. | Heat and strong pressing |
Once the parts are joined, you need to have a strong press, you need to use a heavy load or a special roller to push the air bubbles from the center to the edges, and you need to have a full polymerization of the glue, which takes 24 to 72 hours, depending on the humidity and temperature, and you can't load the mount before that.
⚠️ Attention: Do not glue in the cold or in the direct scorching rays of the sun. The optimal temperature for working with PVC adhesives is from +15 to +25 degrees Celsius. In the cold, the glue will not catch, and in the heat can boil in the seam.
What to do if the glue hits the boat?
If the glue is not already frozen, it can be carefully removed with a cloth soaked in a PVC solvent. If the glue is frozen, try gently tucking the edge with a blade (very carefully!) or warming it with a hair dryer and erasing. Don't use aggressive solvents like acetone on colored boats - they can remove paint.
Safety and ergonomics of the location of gear
Installing the holders is not only a matter of convenience, but also safety. An improperly positioned rod can cause injury when a boat rolls or an engine jerks, and hanging gear can catch on to the screw when pulling the boat ashore or maneuvering at the water's edge.
The optimal location of the holders depends on the type of boat. NDMA (low pressure inflatable floor) holders are often mounted on rigid cans or special platforms attached to stringers, which allows the gear to be spread across the sides without cluttering the bow passage.
It's important to consider the length of the spinning. If you use long rods (more than 2.4 meters), when assembled, they can rest on the opposite side or interfere with rowing. In this case, it's better to use holders that lock the rod forward or at an angle. It's also worth providing space for the lift and the kukan so that they do not get confused under the feet.
- 🎣 Place the holders so that the line does not touch the sharp corners of the transom or cylinders.
- ⚓ Consider the height of the fisherman: the holder should not interfere with getting up or moving around the cockpit.
- 🔄 Leave free access to cylinder inflating valves in case of emergency pumping.
Ergonomics also means protecting the rod itself: Cheap holders may have sharp inner edges that, when vibrating on a wave, can damage the lacquer coating of the form. It is recommended to use models with a soft inner coating or to glue the inside of the holder with fluoroplastic tape or soft cloth on their own.
Use bright colors for holders or stick a reflective tape on them, which will help to quickly find a rod that has fallen into or overboard, especially at dusk or in poor visibility.
Care for fasteners in an aggressive environment
Water, salt, ultraviolet light and temperature extremes are the main enemies of any equipment on the boat. Even the highest quality fasteners require regular maintenance. Metal elements, unless they are made of marine stainless steel AISI 316Plastics, when exposed to the sun, become brittle and fade.
After each fishing, especially in salt water, the fasteners should be washed with fresh water. The salt, when dried, forms crystals that act as an abrasive and accelerate the destruction of the material. If the holder has moving parts (latches, swivel mechanisms), they should be periodically lubricated with silicone lubricant, which is not aggressive to rubber seals and plastic.
Check the glue seam regularly, and if you see bubbles, if you see edges detached, if you change the color of the glue around the site, you're going to have to disassemble the attachment, clean it up, re-glue it, and ignore the minor defects, you can lose the holder completely at the wrong time.
⚠️ Attention: Don't use aggressive household chemicals or solvents to clean plastic holders. They can break the structure of plastic, making it brittle. Use only soap solution or special PVC cleaners.
For winter storage, it is better to free the boat from attachments. Prolonged tension of the material in the attachment areas (especially if the holder is fastened with belts) can lead to deformation of the cylinder.
Comparative analysis of popular models
There are many brands on the market, from Chinese OEMs to eminent firms like Rapala, Stowe or FlagmanCheap analogs often copy design, but are inferior as materials. Chinese plastic can be thinner, and rubber seals can lose elasticity faster.
Expensive models often offer additional features: built-in bait organizers, the ability to fit into different pipe diameters, reinforced construction. However, for most amateur anglers, mid-range models are enough, the main thing is that the manufacturer indicates compatibility with PVC and provides quality adhesive in the kit.
When choosing, consider versatility: A fastener that can be moved from one boat to another or used on different types of boats will be a better investment, and repairability is also important: can rubber liners or fasteners be replaced if they are lost.
The best fastening is the one that is securely fixed, does not damage the boat and is convenient for your fishing style, not the most expensive or branded.
In conclusion, the installation of spinning holders is a simple but effective way to improve your fishing comfort, and properly selected and installed accessory will allow you to focus on the fishing process without being distracted by holding the fishing rod or finding a place to store it.
Can I use car holders for a PVC boat?
Theoretically, you can adapt the way you attach it (e.g., stick a pad). However, car holders often have an aggressive design with sharp edges and are not designed to be in constant contact with water and salt. They can quickly rust or damage the fabric of the boat.
Which glue is better to use for PVC: two-component or polyurethane?
Two-component adhesives (based on polyurethane) are considered more durable and elastic, they better withstand tear loads. Single-component adhesives are easier to use, but can yield in durability under extreme loads. For spinning holders, where reliability is important, two-component formulations are preferred.
Do I need to clean the surface of the boat before gluing it if it is new?
Yes, it is. Even on a new boat, the surface can be covered with factory lubrication or have an oxide film, which will reduce adhesion. Easy skinning with fine sandpaper (granularity 200-400) will significantly improve adhesion of the adhesive to the material.
Will the adhesive attachment withstand heavy trolling spinning?
Yes, if the bonding technology is followed and a sufficient area (minimum 80x80 mm) is used, it is recommended to use not one but two attachment points or specialized reinforced platforms for load distribution for heavy rods.