Trolling from an inflatable vessel is radically different from fishing from a hard side, primarily due to the lack of the usual rigid structures. Fixing spinning to PVC boat It becomes not just a matter of convenience, but a critical safety feature for the entire gear and the boat itself, and an improperly installed holder can cause the loss of an expensive rod or, worse, damage the cylinder, jeopardizing the integrity of the entire boat.
Unlike metal boats, where drilling holes is a standard procedure, PVC The material requires a delicate approach and the use of specialized solutions. Modern technology allows you to organize a full-fledged trolling platform, keeping the cylinders tight and mobility of equipment. You will have to choose between stationary and removable systems, weighing all the risks of metal contact with rubber.
Effective organization of the workplace on the water is the balance between the reliability of the rod fixation and the speed of response to the bite. rod You can have a line overflow and you can lose your trophy, and a good approach to fittings and installation methods will make your inflatable boat a full-fledged trolling boat.
Criteria for the selection of holders for inflatable boards
The first thing that fishermen should pay attention to is the material of manufacture. holderFor PVC boats, it is strongly recommended not to use cheap plastic of low quality, which in the cold becomes brittle, and in the sun loses its geometry.
The second parameter is the type of attachment to the surface, and because you can't drill cylinders, you use systems that rely on the existing elements of the boat: liner cables, rim bolts or special platforms that are attached to the transom. Fixers should have soft pads in the areas of contact with the fabric to avoid friction and rubbing of the material during pitching.
⚠️ Warning: Metal attachments must not have sharp edges or barbs. Any sharp protrusion can instantly tear the cylinder in a sharp roll or strong wave.
The choice also takes into account the angle of inclination and the possibility of adjusting the position. rodFor trolling, it is important that the form is at the right angle to the water, providing the desired depth of diving of the bait. Some models allow you to change the angle from 15 to 90 degrees, which gives flexibility in setting up the wiring.
Schemes for rod placement on PVC boat
Right. layout The key to successful fishing without overlapping. On a narrow hull of an inflatable boat, space is limited, so the classic fan scheme works with difficulty here. Most often, rods are placed on the sides using remote mounts, or a special platform behind a transom.
If you use two spinning wheels, you can spread them out on different sides at or just behind the seats, and you need a retractable design for three or more rods. Trans holder It allows you to place up to four tackles at the back without taking up useful space in the cockpit, which is especially true for boats up to 3.5 meters long.
It is important to consider the length of the overhang of the line and the possibility of free passage of the glitter or wobbler when catching. The scheme should exclude the situation when the cut fish brings the gear under the bottom or behind the floating anchor. gear Minimizes the risk of confusion.
When placing more than two rods, use different handle or coil colors to visually monitor each tackle and quickly identify the spinning that is working.
Installation on the liner cable: step-by-step instructions
Installation of holders on a liner cable (stretched along the side of the cord) is the most popular and safe method for PVC boatsIt doesn't require drilling, and it allows you to easily move the mounting point along the side, and you'll need special locking clamps that are put on the cable to fit it.
First, you have to make sure that the liner cable is tight enough and does not sag under the weight of the holder with the rod. clampIt's a clamp that's locked by a screw or a quick-removal system, and it's already mounting the holder's pipe at the right angle.
☑️ Installation on the leer
The main advantage of this system is mobility. You can easily move it. rod It's closer to the bow or stern by changing the angle of the wiring, and when you're transporting a boat, you can remove the holders easily without taking up too much space in your bag.
transom platforms and their features
For serious trolling, transom platforms are often used that are attached to the motor or directly to the trunk of the boat. spinning It's the size of the body, which is especially important when you use downriggers or heavy gliders, and the platforms are foldable and stationary.
The mounting to the transom is done through special brackets covering the top of the transom board, and it is important that the contact points are protected by rubber pads. Aluminum platforms Steel is preferred over steel because of its lower weight and corrosion resistance, although steel is stronger when working with heavy equipment.
| Type of attachment | Load capacity | Difficulty of installation | Risk for PVC |
|---|---|---|---|
| On the liner cable. | Low/Medium | Minimum | Minimum |
| Tranza platform | High. | Medium | Medium (vibration) |
| On the slap bolts. | Medium | High. | Low. |
| Built-in floorboard | Medium | High. | Missing. |
When using transom systems, you should be aware of the vibration transmitted from the motor. Constant shaking can weaken the threaded joints, so (regular check) tightening of the bolts is mandatory. Fixers shall be fitted with locking elements to prevent spontaneous unwinding.
Balloon protection and gear safety
Security balloon Any mount, even the most reliable, is a potential threat if it is not used properly, the basic rule is that no metal part should constantly touch the fabric under load, use additional soft linings of neoprene or tight rubber at points of possible contact.
Pay special attention to fixing the rod itself in the holder. When trolling on the wave, the spinning can jump out of the glass if you don't use it. supple Loss of tackle at full speed is a common occurrence that is easily prevented by simple insurance.
⚠️ Warning: Never leave rods in holders when passing shallow water or grass thickets unattended. The hook can flip a light boat or rip the holder with a piece of cloth.
Also, consider the effects of the sun on materials. Cheap plastic holders can deform, and rubber seals can dry. fixation Replace worn-out items in a timely manner.
What if the holder has broken the fabric?
If you have a puncture or rupture, immediately shut down the engine and try to seal the damage with a remix. The main thing is not to panic and quickly get the boat ashore for full repairs. Water at the puncture site can come quickly, so have a pump or scoop on hand.
Frequent mistakes in organizing trolling
One of the most common mistakes is to overload one side, and placing all the rods on one side creates a dangerous roll that can be thrown into the air. PVC It's not only inconvenient for fishing, it also reduces the stability of the boat.
Another mistake is to use too rigid fasteners without cushioning, if you bite a large fish or get hooked hard. holder The rod should be able to play a little bit, extinguishing the inertia, and it might break down, and it might damage the side of the boat.
Don't forget to organize the space in the cockpit, because hanging fishing lines, decomposed tools and loose elements can cause an emergency. Order. On board, it is not only aesthetics, but also safety.
The main principle of trolling on a PVC boat is to minimize risks to the integrity of the cylinders while maintaining the functionality of the tackle.
Maintenance and maintenance of fittings
After every fishing trip, especially in salt water, all metal elements must be washed with fresh water. stainless steel, causing corrosion, which over time can spread to the fabric of the boat.
Rubber and plastic cells also require maintenance, and they should be wiped with a wet cloth and treated with special formulations to protect against ultraviolet light, which will prolong the life of the body. fixator And it'll keep them elastic.
Before long-term storage in winter, all removable elements are better dismantled and removed in a warm room, left in the cold plastic parts can crack, and metal parts can become covered with excess oxide.
How often should the seals be changed on the holders?
Rubber seals are recommended to be inspected before each season, and if you notice cracks, loss of elasticity or traces of material crumble, they should be replaced, and on average, during active use, you need to replace them every 2-3 years.
Can I use homemade holders?
You can use it, but only if you're confident in the strength of the structure and the safety of the materials. Water pipe brackets often have sharp edges and are not reliable enough to troll large fish.
What is the best angle for trolling?
The optimal angle depends on the type of bait and the speed of the boat. spinning They're set at an angle of 45 to 60 degrees to the water, and for deep-sea wobblers, the angle can be more gentle to increase the depth.