Fishing from a swimming facility is radically different from shore fishing, requiring the most reliability from gear and equipment. In conditions of constant swaying on the wave and limited space of an inflatable vessel, competent organization of storage of gear becomes critical. Fastenings for rods on a PVC boat It's not just a comfort accessory, it's a necessity to keep the expensive spinning wheels safe and the angler safe, and a properly matched holder allows you to react instantly to the bite and frees your hands to operate the craft.
The modern market offers many options for fixation, from simple plastic glasses to complex mechanical systems with angle adjustment. The choice of the specific type depends on the design of your boat, the number of gear used and the preferred fishing style. An improperly installed lock can damage the board or cause the rod form to break when a large fish jerks. In this article, we will discuss in detail the types of fasteners, their features and installation rules, so that your fishing goes without unnecessary problems.
Main types of holders for inflatable boats
All existing fixation systems can be divided into several categories according to the principle of installation and design. cupThese are hollow tubes with a water drainage hole, which can be made of plastic, aluminum or stainless steel, and they're versatile and suitable for most types of rods, providing a reliable grip on the rod.
More complex designs include mechanical They allow you to lock the form anywhere in the handle, which is especially convenient when using spinnings of unusual length or shape, but such mounts require more careful handling, so as not to damage the rod or lacquer coating of the form when shaking.
- 🎣 Overhead models mounted directly on board or paioles using bolts or screws, providing a rigid design.
- 🎣 Pressure holders - are attached to the edge of the side or transom using screw clips, without requiring drilling.
- 🎣 Embedded systems - are installed in special profiles (for example, a D-shaped profile), allowing you to move gear along the side.
- 🎣 Universal hinge anchorages - allow you to change the angle of inclination of the rod, which is useful for trolling or catching in windy weather.
When choosing the type of fastening, it is important to consider the material of manufacture. Plastic options are cheap and not afraid of water, but can crack in the cold or from a strong impact. stainless steel Anodized aluminum, which lasts for decades, but requires monitoring of the condition of fasteners.
⚠️ Attention: When using metal holders, make sure that all contact surfaces are smooth and do not have sharp edges that can rub the PVC fabric or damage the rod form when pitching.
Methods of installation on board and transom
Installing anchors on inflatable boats requires a special approach, as standard drilling methods are often not applicable or undesirable. pressing-upThey are fixed to the top inflatable cylinder or rigid shaft profile (if any) with screw clips, often complete with kayaking holders or side brackets.
If your boat is a tough one turret (wood or aluminum), the installation process is greatly simplified, in which case you can use screws or bolt joints, drilling holes beforehand. To protect the wood from moisture of the attachment site, it is recommended to treat the sealant or varnish. Installation on the transom allows you to place the tackle behind the angler's back without taking up useful space inside the cockpit.
Particular attention should be paid to the installation of D-shaped profileThis is a special pocket of durable fabric sewn along the side, which is inserted into a rigid bar, which is already attached to various accessories, including rod holders, which allows you to move the gear to any convenient place along the side without re-drilling or re-arranging the clips.
☑️ Pre-installing check
Use of floorboards and Hard Gender
Owners of boats with rigid decking (floorboards) of plywood or aluminum have a unique ability to install mounts directly on the floor. This solution frees the boards for other tasks and allows you to place the gear in close proximity to the seats. flange-holderAnd they are sliding to the surface of the floor.
When mounting on plywood floorboards, it is critical to ensure waterproofing of the attachment sites. Water entering the layered plywood will swell and dissect the material, which will quickly disable the floor. Aluminum floors are more stable in this regard, but also require accuracy in drilling, so as not to disrupt the corrosion coating.
| Type of attachment | Place of installation | Difficulty of installation | Reliability |
|---|---|---|---|
| A glass of screws | Tranza, paiola. | Medium | High. |
| Pressure-clamp | Borth, vestibule profile | Low. | Medium |
| Insert in the D-profile | Board (pocket) | Low. | High. |
| A paddle bracket | A fun-loving squirrel. | Low. | Low. |
It is important to consider that mounting on the floor can interfere with movement inside the boat, so often use removable structures or install them closer to the sides, and it is also worth remembering the height of the installation: too low a holder can take water in choppy conditions, and too high will interfere with the view and control.
Materials and durability of structures
Aggressive aqueous environment, ultraviolet radiation and mechanical loads dictate strict requirements for the materials from which they are made. rod-mountingThe plastic used in budget models must be frost-resistant and resistant to fading. Cheap polymers become brittle when exposed to the sun and can burst at the most inopportune moment.
Metal components such as bolts, nuts and holder housings themselves must be made of stainless steel AISI 304 or AISI 316. Conventional zinc-coated steel rusts quickly in salt water or even fresh water with frequent use. Anodized aluminum alloys also show excellent results, combining lightness and strength.
How do you extend the life of the fasteners?
Lubricate threaded joints regularly with silicone lubrication to prevent metal from boiling. After each fishing, especially in salt water, rinse the fasteners with fresh water to remove salts and sand that act as an abrasive.
Rubber or plastic inserts inside glasses play an important role in shock absorber, they suppress the vibration of the form and prevent scratches on the rod lacquer coating. Over time, these inserts can wear out or lose elasticity, so their condition should be periodically checked and replaced if necessary.
Features of operation in trolling
Trolling places increased demands on the reliability of fixing tackles, when the boat moves on the rod, there is a constant load from the resistance of the bait, as well as dynamic jerks when the waves pass. Fastenings for rods on a PVC boat In this case, they should provide not only vertical fixation, but also limit horizontal displacement.
Special trolling is often used for trolling. outrigger Or remote brackets that allow the gear to be spread across the sides, avoiding the overlap of the line, and the angle of the holder's tilt plays a key role in this case: it should allow the rod to work as a nod, signaling a bite, but not let the form pop out of the nest when a sharp jerk.
⚠️ Attention: When trolling on an inflatable boat, never tie the fishing line to the board or structural elements. In the case of a hook or bite of a large predator, this can lead to the boat tipping over or serious injury to the angler.
It's important to calculate the load on the anchorage point correctly. When you fish a large fish, the force is transferred to the side or the trawler. If the holder is mounted on a soft inflatable cylinder without a rigid base, it can simply tear out a piece of cloth. Therefore, for active fishing, it is preferable to use transom mounts or rigid inserts in the D profile.
Additional accessories and upgrades
Standard holders can be greatly improved with additional accessories. replacement The same glass can be used for spinning and powerful sea rods, and fast-shift systems are also popular, allowing you to extract the rod in one motion, which is critical when catching active fish.
For night fishing or fishing in low visibility, reflective elements or the ability to install LED beacons on the holder will be useful, which will help to quickly find the gear in the dark. Some anglers equip the mounts with small carbines to fix the coil, preventing it from spontaneously turning when shaking.
Don't forget to protect the rods themselves, and if you're planning long walks or keeping gear fixed, use covers or special capes to protect the blank from sun and splash, and prevent sand and dirt from getting into the coil mechanism.
Frequently Asked Questions (FAQ)
Can the holders be attached directly to the inflatable cylinder without a rigid base?
It is strongly recommended not to attach rigid structures directly to the soft fabric of the balloon without the use of special linings or profiles. Pressure at the attachment point when pulling a fishing rod can damage the material. It is better to use a D-shaped profile or transom mounts.
Which material is better: plastic or metal?
Metal (stainless steel, aluminum) is stronger and more durable, but heavier and more expensive; plastic is lighter and cheaper, but less resistant to shock and ultraviolet light; for most anglers, quality plastic glasses with metal fasteners will be the best trade-off.
Do I need to lubricate the thread of the fasteners?
Yes, regular lubrication of threaded joints with silicone or graphite lubrication is necessary, which will prevent corrosion and "fixing" of the bolts, allowing you to easily dismantle the mounts at the end of the season.
How to avoid overlapping lines when installing multiple holders?
Arrange the holders at a sufficient distance from each other (at least 30-40 cm) and use different angles of inclination. For trolling, it is effective to use remote slats (outriggers) that spread the tackle to the sides.
Safety and reliability of PVC boat gear attachment is more important than convenience. Always check the fixation before you get on the water.