The modern market of small craft is full of offers, but among them stand out time-tested models of domestic production. Ufimka inflatable boat 22 It is well-deservedly popular with fishermen and hunters for its reliability and affordability, and it balances compact transport with sufficient space to accommodate one or two people with the right equipment.
The main material for manufacturing is reinforced PVCIt's a keel that provides high wear resistance and puncture resistance, and unlike cheap ones, it's often equipped with an inflatable keel, which greatly improves the rideability of the wave. outboardThis makes a boat a full-fledged fast boat.
In this article, we will discuss the technical details, consider the design features and answer the questions that arise from potential buyers. Understanding the specifics of operation will help you make the right choice and avoid common errors in the maintenance of the boat.
Structural features and materials of the body
The foundation of durability of any boat is the material from which it is made. Ufim 22 High-density multilayer polyvinyl chloride is used. Five-layer fabric It provides excellent tightness and resistance to ultraviolet radiation, which is critical for long-term operation under the open sun.
Special attention should be paid to the system of seams. In high-quality instances, the hot gluing method is used, which creates a monolithic connection that is not inferior in strength to the material itself, this eliminates the stratification of the side even under extreme loads or sudden temperature changes.
⚠️ Warning: When buying a used boat, carefully check the seams for bloating or detachment. Even a microscopic gluing defect can lead to depressurization on the water.
The design of the bottom also deserves a detailed review. keel (K) gives the bottom a profile close to the hull of rigid boats, which allows effective wave breaking and reduces water resistance when driving for an outboard motor.
Technical specifications and load capacity
The numbers speak for themselves when it comes to water safety. Ufim 22 It's designed to withstand heavy loads while remaining maneuverable, and it's a standard length of 220 cm and a width of 120 cm, which is the optimal ratio for this class.
The capacity of the vessel allows you to carry on board not only passengers, but also a significant amount of equipment. However, it is important not to confuse the maximum load capacity with the recommended one.
Below is a table with the main parameters that will help you navigate in the choice:
| Parameter | Meaning | Note |
|---|---|---|
| Full length | 220 cm | Dimension inflated condition |
| Width | 120cm | Internal size |
| Load capacity | 220 kg | Including boat weight |
| Boat weight | 18-22 kg | Depends on the configuration. |
| Engine power | up to 5 hp | Recommended traction |
The weight of the boat itself in running order varies depending on the availability of sleigh and the type of decking. For carrying alone, this is quite a lifting weight, although the presence of a large number of sleighs is not a problem. coatboard from moisture-resistant plywood adds a few kilograms.
Set: slate, transom and accessories
The comfort of being on the water depends on what is under your feet. The basic equipment often includes waterproof plywood flooring, covered with special film. slate It distributes the load evenly and protects the cylinders from abrasion.
The tray is made of durable plastic or laminated plywood and is designed to install an outboard motor. The design allows you to reliably fix the lower unit, eliminating its displacement even when passing a steep wave or a sharp start.
☑️ Checking the completeness when buying
It is important to note that some manufacturers may change their equipment, so make sure to check the availability of:
- 🎒 Bags for transportation - dense and with comfortable straps.
- ⚓ Anchor-rim - for fastening the fag.
- 🔧 Remake - with glue and patches of the desired color.
- 🚣 The switch and fun - if the model assumes a rowing option.
The quality deserves special attention. fittingsThe can mounting Velcro straps must be held rigidly, and the etching valves must provide rapid pressure relief without jamming.
Operation for an outboard motor and on oars
Use of use Ufam 22 It's a very different experience from the ride, and it's a very safe, single-passenger, minimal-load vessel, but it's not a race car, it's a utilitarian vessel.
When steering on oars, the boat shows good course stability. The wide balloon works as an effective spray-breaker, keeping clothes and equipment dry even in bayonet waves. Rowing requires a certain skill, because the width of the hull dictates its amplitude of movement.
⚠️ Warning: Never exceed the recommended power of the motor. Installing an engine that is too powerful can lead to deformation of the transom and loss of control of the vessel.
For fishing in stagnant water or in low water, this model is perfect. It's quiet, which is important for duck hunting, and it's stable enough to throw spinning off the board. Whipped bottom helps to keep the course better in the side wind compared to flat-floorers.
Rules for storage and care of PVC
The life of your boat depends on how you store it in the off-season. Polyvinyl chloride does not like prolonged exposure to direct sunlight when deflated, as this can lead to layers of tissue clumping together.
Before packing for the winter, the vessel must be thoroughly washed with clean water and completely dried, and the humidity inside the bag is the main enemy, contributing to mold and unpleasant odor, which is difficult to get rid of later.
How do you fold the boat properly?
Stack the boat in different lines every time, change the folds to avoid microcracks on the PVC folds, and this will extend the life of the material several times.
It is best to store the product in a straightened form at room temperature, if this is not possible, it is permissible to pack in a bag, but without excessive compression, the optimal storage temperature is from +5 to +25 degrees Celsius.
Periodically, it is recommended to treat the surface with special PVC care products that restore elasticity and protect against ultraviolet light, especially for boats that are often in the open air.
Comparison with analogues and final conclusions
Against the backdrop of competitors Ufim 22 It looks confident because of its combination of price and quality, and unlike its Chinese counterparts, it uses thicker and more reliable materials, and the design of the seams has been tested for decades in harsh conditions.
However, it is worth considering that the weight of the boat can be higher than that of ultra-light models made of thinner PVC. This is a price for strength and durability. For those who value reliability above minimum weight, this will not be a problem.
When choosing between models with a hard and inflatable floor, remember: the inflatable floor is easier to collect by one, but the hard slate gives better stability when cruising inside the boat.
In conclusion, it is a universal solution for summer residents, fishermen and water lovers, and its simplicity minimizes the risk of breakdowns, and its maintainability allows you to eliminate minor damage on your own.
Ufamka 22 is a workhorse for small water bodies, offering the optimal balance between cost of ownership and functionality for 1-2 people.
Frequently Asked Questions (FAQ)
Can I put a 9.9 hp engine on Ufamka 22?
Technically, the transom can withstand a short-term load, but the product instructions and passport usually limit the power to 5-8 hp Exceeding these norms removes the warranty and creates a risk of destruction of the transmutation board.
Which glue is better to use for puncture repair?
For PVC repairs, two-component polyurethane adhesives are best used, providing a flexible and water-resistant seam, and a normal "moment" may not withstand the tear load of a pumped cylinder.
How long does the glue dry during repair?
The polymerization time depends on the ambient temperature. At 20°C, the primary grip takes 20-30 minutes, but the glue is fully strong after 24 hours. Don't rush to pump the boat immediately after gluing.
Will the boat withstand the rocky shore?
The material is resistant to abrasion, but the sharp edges of the stones are dangerous, it is recommended to use protective linings on cylinders or drag the boat by the flounder, minimizing contact with the ground.