Quiet breams and grassy backwaters are good for spinning, but when it comes to catching a large bream or an ulcer, experienced anglers go to the fairway. Here, in deep places with a noticeable current, the fish feels confident and actively feeding, being carried away by the flow of water. ring-fishing A method that allows food to be delivered precisely to hooks at great depth, creating a powerful attracting stream.
The essence of the method is simple, but requires a certain skill and proper preparation of equipment. The fisherman installs the boat across the jet or on the anchor stretch, lowering a massive feeder to the bottom. A special metal ring worn on the feeder cord is passed through the main fishing line, which ensures that the bait is delivered exactly into the plume of the washed food. It is not just fishing, it is an engineering approach to angling bottom fish.
To implement this method, you will need a reliable boat, as fishing often takes place on the fairway with active navigation, and a high-quality anchor site. Fishing on a ring from a boat on the current This involves the use of a rough but robust enough gear to withstand the resistance of a large fish and the pressure of the flow, so let's take a look at how to assemble an effective tool and not miss the trophy.
Principle of operation and advantages of the method
The key to the effectiveness of this gear is the physics of the process: the feeder, when lowered to the bottom, is eroded by the current, creating a long plume from the suspension of the feed, and the fish that goes against the current inevitably enters this feeding path. The RingAnd the sliding of the feeder cord allows the hooks to be positioned vertically, so they're always where the feeding flows, and without this device, it takes a few seconds to pull the hooks away from the feed stream.
The advantage of this method is that you can fish at any depth, in any current, even the strongest, so as long as the anchor holds the boat and there is bait in the feeder, fishing can go on for hours, this is a passive but extremely effective way, often called a "ladder", but it is worth remembering that success depends on the right choice of parking place.
Always check the strength of the current before anchoring. If the jet is too weak, the feeding plume will not form and the fish will not fit the gear.
It's also important to take into account seasonal factors. In spring and early summer, when the fish are active and flocking, the method works smoothly. In autumn, with the water cooling, the efficiency may decrease, but trophy specimens often continue to peck at depths where other gear simply does not reach.
Choice of boat and anchor system
Because fishing takes place on the current, often in the fairway of major rivers, the requirements for the boat are high. The boat must be stable and wide enough that the angler can comfortably handle long anglers and a heavy feeder. PVC Boats with inflatable sides are popular, but the metal flat-bottom ("Kazanka" or "ob") will be more stable on the wave created by passing transport.
The critical element is the anchor system. You need two anchors weighing at least 5-7 kg each to be stretched across the current. Using one anchor on the current can lead to a boat turning side to wave, which is dangerous and inconvenient to catch. The anchor cord must be strong, synthetic, with minimal stretchability, so that the boat does not blow.
- 🛶 For fishing alone, the length of the boat is optimal 3.0-3.5 meters, which allows you to conveniently place the tackle.
- ⚓ Use anchor cords with a margin of length exceeding the depth at the fishing site by 2-2.5 times.
- ⚠️ Attention: It is strictly forbidden to tie the anchor cord to the transom or elements of the boat structure without the possibility of rapid uncoupling (for example, on buoys).
Keep in mind safety. You should be visible to passing boats when you are on the fairway, the bright color of the boat, the presence of a flak or reflective elements is a must. Fishing for the ring It often occurs in places where cargo boats are operating, creating a powerful wave.
Tree design and feeding
The basis of success is a well-assembled feeder, and it's not just a mesh of porridge, it's a complex piece of gear. feeder It is a mesh cylinder or cone made of metal or strong fishing line, equipped with a heavy lead bottom. The weight of the bottom can vary from 1 to 3 kg, which is necessary to hold the feeder at the bottom in a strong current.
The feeder needs to be closed, so you can submerge it in a closed form so you don't lose the bait in the top water, and open it on the ground, and you can do this by using a simple mechanism: the lid is spring-loaded or tied with a thin line, which is interrupted by a sharp jerk after lowering.
| Type of feeder | Weight of cargo | Volume | For what current? |
|---|---|---|---|
| Metal mesh | 2-3 kg | 3-5 litres | Strong, fast. |
| Line net | 1-1.5 kg | 2-3 liters | Average |
| Plastic can | 0.5-1 kg | 1-2 liters | Weak. |
| Bag (waska) | 1-2 kg (stone) | 5 litres | Any (budgetary) |
The bait should be viscous and inert, based on steamed millet, barley, peas or special pellets, and it is important to add binders (clay, earth) so that the food is washed out gradually, over 30-40 minutes, if the feeder is empty in 5 minutes, the fish will leave.
The recipe for "killer" bait
Cook 2 kg of millet to half-ready. Add 1 kg of makuha (cake), 0.5 kg of breadcrumbs and a glass of unrefined sunflower oil. For weighting and viscosity, add clay from the shore. This mixture works on large bream and ulcer.
Installation of tackle: fishing rod and ring
The ring fishing gear itself is different from the classic feeder or donck, which does not require long-range throwing, since the boat is directly above the fishing point. The rod is short, 1.5-2.0 meters long, with a hard whip. The rod test should be high, because the catching takes place "in the forehead", without the ability to release the fish.
The key element is: ring.. They used to be poured out of lead, now they use brass or steel, the ring has a hole to let the feeder cord through, and an eye to attach the line, and there are slotted rings (eggs) that make it easy to remove the gear without pulling out the feeder, which is very convenient when catching a large trophy.
The installation of the main line is simple: it is passed through the ring (or tied to it if the structure is solid), then the tool is knit at the end. Usually it is a short coil or a small coil. The line is used monophilic, with a diameter of 0.3-0.4 mm, or a wicker of 0.15-0.2 mm. The wicker is more sensitive, but the monophile is better at cushioning the jerks of large fish on the current.
- 🎣 Steering: side fishing rod or short spinning (up to 2 m).
- 🧵 Line: 0.35 mm monofile or 0.18 mm wicker.
- 🪝 Hooks: No. 8-12 in international classification, with a long forearm.
- ⚠️ Attention: Don't use too thin fishing lines. During the course, the sailing gear is high, and the resistance of large fish in the water flow increases many times over.
The tooling is most often a leash or a garland of 2-3 hooks, the distance between the hooks should be such that they do not get confused, but are in the range of the plume, the optimal length of the leashes is 20-40 cm, depending on the strength of the current.
Fishing process and catching technique
The fishing technique starts with the right fit. The boat is placed across the current on two anchors (stretches). The feeder is lowered from the side upstream (or from the nose if the boat is facing upstream, but this is less common). The feeder cord should be pulled like a string.
After lowering the feeder, a ring is put on the cord with a gear tied, we lower the tooling to the bottom, then slightly lift (by 10-20 cm) and fix the fishing line, and now the current will stretch the leashes into the line, and they will be in the stern path, all that remains is to wait for the bite.
☑️ Algorithm of actions on water
The pecking on the current feels like a confident but smooth pull. Fish, when they take a nozzle, often feel no resistance due to the free slip of the ring. The cut should be short and sharp, but without a strong amplitude, so as not to cut the lip of the fish, and the fish is harvested by taking the line with their hands, going through it.
If you get a big bream or a sazan, don't rush. Let the fish get tired in the flow of water, periodically pulling up and releasing the line. The main thing is not to let the line sag, otherwise the current will confuse the gear around the feeder cord. Bring the fish to the boat from the leeward side.
The key to success is to have fresh feeding in the feeder, and once the peel stops, the feeder needs to be lifted and recharged.
Frequent mistakes and expert advice
Despite the apparent simplicity, beginners often make mistakes that reduce their performance to zero. One of the main ones is the wrong choice of place. If you stand on a flat table without a current, the method will not work. If you stand on too fast a flow, the tackle will tear down and the ring will jam. You need a "golden mean" - a smooth, confident current.
Another mistake is to use bait, which is quickly washed out, the dust mixture will flow away in a couple of minutes, collect small change, but will not hold the large fish, the bait must be heavy and sticky, and often ignore the length of the leashes: too short will not allow the nozzle to play in the flow, too long - get confused.
⚠️ Attention: Never leave the feeder cord unattended or unattached. With strong winds or passing waves, the boat may pull, and the cord with a heavy feeder may injure the arm or become entangled in the engine screw.
Experts also advise to pay attention to the time of day. Fishing for the ring It's most effective in the early morning and evening, but on cloudy days with moderate winds, the sticks can be stable all day. Don't be afraid to experiment with the nozzles: worm, horn, barley, dough — fish preferences change.
And remember the fishing rule: respect nature. Don't leave any garbage behind, especially fishing line and bait bags. The river is a living organism, and our job is not only to take it, but to preserve it.
Can I catch a ring from one anchor?
Technically possible, but extremely inconvenient and dangerous, the boat will be turned on board to the current and wave, in which case the gear will constantly get tangled around the anchor rope, and the feeder will be demolished under the boat, the use of stretch marks (two anchors) is a prerequisite for comfortable and safe fishing.
Which one works best on the sleeve?
The classic is a bunch of dung worms or a large crawl. And sandwiches like worm + wool, barley + corn work great, and in the summer heat, bream may prefer plant nozzles like mastro, peas or flavored dough.
Do you need a special rod?
You don't have to buy a special rod. Many anglers have been successful in using short spinning, winter rods for glittering, or homemade side fishing rods, and the main requirement is that they have a stiffness and a comfortable handle, because the rod often has to be held in their hand.
What to do if the ring is stuck on the feeder?
If the ring (especially the whole one) is stuck on the node or the feeder element, don't pull sharply. sway the gear carefully, try to choose the slack of the feeder cord. If it doesn't work, you have to raise the feeder, which is why connector rings ("eggs") are considered more progressive.