Modern fishing has long ceased to be the lot of ascetics, ready for hours to get wet on the shore or paddle against the wind. Motor-powered inflatable boat It's become an indispensable tool for those who value mobility, speed and comfort on the water, and the ability to quickly reach remote brows, catch a vast area and return with a catch is what a competent boat package gives.
The market offers many options, from light single "cakes" to serious three-meter machines capable of withstanding the wave and trophy fish. PVC boats It's always a trade-off between weight, payload and cost, and a wrong motor or a bottom that's too light can turn pleasure into a fight for survival.
In this article, we will discuss all the nuances, from the choice of material cylinders to the installation of attachments. cross-board It's more important than it sounds, and how to avoid common assembly errors, and being ready for the season starts with knowing what you need on the water.
Criteria for Choosing the Perfect Boat for Fishing
The first thing to look at when buying is loading capacity. Many beginners mistakenly believe that it is enough to choose a model designed for the weight of one person, but you need to consider the mass of equipment, anchor, sonar and, of course, the engine itself.
The second critical parameter is the hardness of the bottom. slate-rug But if you're going to go fishing in large areas where there's wind waves, you're going to need to do it. high-pressure It provides excellent seaworthiness, but it adds weight to transportation.
⚠️ Warning: Never exceed the maximum power allowed on the boat's passport. Exceeding the limit can lead to the transom torn off and the boat to tip over at full speed.
The third aspect is the number of inflatable compartments. flyboat You have to have at least two independent cylinders, and if you puncture one of them, the other one will keep you afloat and get to shore, and ignoring that rule puts your life at risk.
Design features: cylinders and bottom
The fabrication material plays a key role in the durability of the craft. reinforced PVC It consists of several layers of polyester-coated tissue, measured in grams per square meter, and for fishing models, the optimal range is between 750 and 1100 g/m2.
The design of the bottom directly affects the behavior of the boat for an outboard motor. Hard Bottom provides better hydrodynamics and allows you to develop higher speed. Soft bottom is more comfortable when landing, but less maintains stability. The choice depends on the operating conditions.
- 🛶 The slate bottom - a classic solution where the floor is assembled from individual plates inserted into special pockets.
- 🎈 NDMA - inflatable floor, which is inflated to a pressure of 0.2-0.25 atm, providing a rigidity comparable to plywood.
- 📏 Keel beam - an element that runs along the entire bottom, which improves the germination of the wave and the course stability.
It's also important to pay attention to the protection of cylinders. flat-bar The perimeter protects the boat from impacts on the pier, rocks and other boats, and their absence significantly reduces the life of the product during active operation.
The effect of the color of the boat on the
It is believed that boats of protective color (olive, camouflage) are less frightening fish in clear water. However, for safety on the water, bright colors (orange, salad) make you noticeable to other water engines, which is critical in fog or dusk.
Choice of outboard motor: power and type
Engine picking is a science that requires balance. Too weak. boat-engine It's not going to take the boat to the plane, it's going to use more fuel and it's going to create a dangerous wave of kilvater, and it can destroy the transom or make the boat uncontrollable for an inexperienced driver.
The main division occurs in two-stroke and four-stroke units. Two-tacters They're lighter, cheaper, and they work on a mixture of gasoline and oil, and they're ideal for short-term drives and trunks in a car. Four-stroke engines It is heavier, but quieter, more economical and more environmentally friendly, as they work on clean gasoline.
When choosing, consider the length of the daydwoot. Inflatable boats are usually suitable motors with a short leg (S - 381 mm). Long leg (L - 508 mm) designed for boats with a high transom and inflatable will work incorrectly, capturing air.
| Motor type | Weight (kg) | Fuel consumption | Features |
|---|---|---|---|
| two-stroke 2.5 hp | 9.8 | 1.2 l/h | Light, requires mixing of oil |
| two-stroke 5bhp. | 19.0 | 1.6 l/hour | Optimal for planing 1+1 |
| four-stroke 5bhp. | 25.0 | 1.1 l/hour | Quiet, economical, but heavy |
| two-stroke 9.8bhp. | 26.0 | 2.5 l/hour | Maximum for 3-meter boats |
When buying a two-stroke engine, immediately purchase a separate fuel tank with a pear. Staff tanks often have a small volume, which often causes you to interrupt fishing for refueling.
Operation and assembly on a reservoir
The process of preparing for the launch requires a systematic approach: first, the boat is laid out on a flat surface, cleared of sharp objects, pumped cylinders to the operating pressure specified in the instructions (usually 0.2 atm), pumping in the heat is dangerous to break seams, under-pumping reduces the rigidity of the structure.
The motor is mounted in the center of the transom, and the fasteners are tightened with effort, but without fanaticism, so as not to damage the wood or the plastic of the transom board. anticavitational The engine was parallel to the bottom of the boat or was buried 1-2 cm below the bottom level.
After descent, be sure to check for water in the hold, even a microscopic amount of water can indicate leaky valve or etching seam, in which case you should immediately return to shore for diagnosis.
- 🔧 Always carry a remix, pump and spare valve.
- ⚓ The anchor should weigh about 1/10 of the displacement of the boat for reliable retention on the current.
- 🧭 Navigating even in familiar places requires a compass or GPS tracker.
☑️ Checklist before getting on the water
Safety and care of PVC boat
After every fishing trip, especially in salt water or muddy rivers, the boat must be washed with fresh water. The silt and sand, when dried, act as an abrasive, damaging the protective layer. PVC.
Store the product in a dry, cool place, in a straightened form or in a special bag, but not in a very compressed state. Direct sunlight, when exposed to prolonged exposure, destroys the structure of the polymer, making it brittle. Use special sprays to protect against ultraviolet.
⚠️ Warning: Do not leave a pumped boat in direct sunlight for long periods of time unattended. The pressure inside the cylinders is increasing, which can lead to rupture of the seams or deformation of the transom.
Check the valves and the joints regularly, and if you put soap on a small air bubble, you need to get repaired immediately, and if you ignore the small defects, you're going to have a lot of water problems.
Proper drying and storage of the boat in the off-season increases its service life by 5-7 years, maintaining the elasticity of the material.
Accessories that improve fishing
The basic equipment of the boat is often minimal, so anglers equip it with additional elements. transom wheels This is a must-have for a solo angler, allowing you to move a heavy motorized boat along the shore without assistance.
For comfortable fishing irreplaceable anchorIt allows you to quickly attach the anchor shaft and, if necessary, easily uncouple it by pulling the ring if the anchor is stuck, and also popular rod holders and sonar platforms.
And remember, the awning or the sun visor, the fishing takes hours, and the protection from the scorching sun or the sudden rain keeps you strong and healthy, and the awnings are attached to arcs that are inserted into special pockets or attached to the fries.
- 🎣 Chairs-seats inflatable tubes increase comfort and stability when fishing.
- 🔦 LED belts on cylinders provide visibility in the dark.
- 📦 Hermbags of various volumes are necessary for storing personal belongings dry.
anchored lifehack
Instead of a heavy metal anchor, many anglers use a "cat" or a bag of rocks drawn on the shore, saving boot space and weight during transportation.
Frequently Asked Questions (FAQ)
Which motor is better for a boat 320 cm long?
For a boat with a length of 320 cm, the best choice will be a motor with a capacity of 5 to 9.8 hp The 5 hp engine will provide confident planing with one angler and a small load. If you plan to take two adults or a large amount of equipment, it is better to consider the option of 8-9.8 hp, but be sure to check the maximum power specified by the boat manufacturer.
Can I repair the PVC boat by myself?
Yes, small punctures and cuts (up to 3-5 cm) can be sealed yourself with a remix that comes with the kit. It is important to use a special glue for PVC and follow the instructions for degreasing and drying. For valve repair or major damage, you should contact a specialized service.
How often should I pump a boat in the heat?
In hot weather, the pressure in the cylinders can increase significantly, it is recommended to check the pressure every 2-3 hours of active operation, if the boat is unattended in the sun, it is better to blow some air or put it in the shade to avoid rupturing the seams.
What is scaling and why is it necessary?
Gleaning is a mode of movement in which the boat slides on the surface of the water, resting on it only part of the bottom, allowing you to achieve high speed with minimal fuel consumption and reduces water resistance. For fishing, gleaming is important for a quick transition between fishing points.
How long does a PVC inflatable boat last?
When properly operated, stored and repaired, a quality PVC reinforced boat lasts 10 to 15 years or more, depending on the frequency of use, storage conditions (UV ray protection) and the accuracy of the owner.