Company NGO Our Boats For more than two decades, the company has been a strong player in the Russian small boat market, from a small workshop to a large production association that produces hundreds of vehicles annually, and is well known to anglers, hunters and water enthusiasts for its optimal combination of price and quality.
The main specialization of the plant is production PVC inflatable boats and aluminum catamaranEngineers are constantly improving fabric cutting technologies, introducing new composite materials for paioles and developing ergonomic transomic inserts, which allow products to withstand the harsh conditions of operation on rivers and reservoirs.
In this article, we will discuss in detail the model range, technical features and nuances of the choice of a boat from this manufacturer. frigate and Solar.You will also get practical advice on how to take care of your boat.
History and philosophy of the NGO brand Our Boats
The production began in St. Petersburg, a city with a rich water tradition, and the founders aimed to create an affordable but reliable boat that would not be inferior to expensive foreign counterparts. NGO Our Boats It uses advanced equipment for welding and cutting materials with precision, and its philosophy is based on three pillars: safety, functionality and maintainability.
An important development step was the introduction of its own technology of reinforcing the sides and strengthening the bottom, which allowed to significantly increase the product's life when in contact with rocky bottom or ice. Polyvinyl chlorideThe stainless steel used in production passes strict quality control and tests for frost resistance.
⚠️ Warning: When buying a boat, be sure to check the presence of the factory number on the transom and its compliance with the number in the product's passport.
The company is actively implementing composite This makes the boat faster and the structure harder, and unlike classical plywood, the composite does not absorb moisture and does not rot, which significantly prolongs the life of the craft.
The main series of inflatable boats from PVC
The range of the manufacturer is extensive and divided into several key areas, each series is focused on specific tasks, from quiet duck hunting to serious trolling in large bodies of water. PVC density from 750 to 1100 g / sq.m.
Series frigate It's positioned as a universal classic, and these boats are equipped with an inflatable keel, which provides excellent wave scent and stability. Kilson system Load distribution allows you to install motors with a capacity of up to 15 hp without the risk of deformation of the transom.
For lovers of maximum load capacity created a series Solar.The peculiarity of these models is the increased width of cylinders and the presence of anchor-pocket The design of the transom board has been reinforced, allowing for more powerful propulsion systems.
- 🚤 frigate - classic keel, ideal for running fishing and family holidays.
- 🎣 Solar. Maximum load capacity, wide cylinders for a stable platform.
- 🏞️ riviera Compact rowing models for calm water bodies and fishing in the thickets.
- 🌊 Profi. Professional models with reinforced bottom for rocky rivers.
Special attention should be paid to the series. rivieraIt's the lungs. rowing-boatThey're easily carried by one person, and despite the lack of an inflatable keel, they're very stable because of the geometry of the cylinders.
Aluminum catamarans and metal boats
In addition to inflatable products, NGO Our Boats The brand's aluminium catamarans have a reputation for being unsinkable and resilient, and are ideal for fishing with two or three people, providing a huge internal volume.
The design of catamarans is based on two sealed floats made of aluminum alloy AMGAnd there's a frame in between that's where the deck is mounted, and this is a scheme that ensures that even if one section is damaged, the boat stays afloat.
Metal boats of the series Solar-K fitted slab-slabAluminum does not require painting and is virtually non-corrosive if you follow the rules of operation, making it an excellent choice for northern regions and salt water bodies.
The Benefits of Aluminum Catamarans
Our boats have unique class stability, even when the fishermen move sharply on deck, the risk of tipping over is minimal, and the flat bottom allows you to approach the shore itself, which is convenient for disembarking with a dog or cargo.
An important advantage of metal models is the ability to install attachmentOn board, holders for rods, sonars and anchor winches can be mounted without fear of damaging the material structure, as is the case with PVC.
Technical specifications and comparison of models
When choosing a boat, it is important to focus not only on price, but also on specific technical parameters. Below is a comparison table of popular models that will help you decide on the choice depending on your needs.
| Model | Length, cm | Width, cm | Load capacity, kg | Engine power, hp |
|---|---|---|---|---|
| Frigate 280 | 280 | 136 | 400 | 2-5 |
| Frigate 330 | 330 | 150 | 550 | 5-10 |
| Solar 350 | 350 | 160 | 700 | 5-15 |
| Pro 380 | 380 | 170 | 900 | 10-20 |
As can be seen from the table, with increasing sizes, not only the load capacity increases, but also the permissible capacity. motor-powerFor two adult fishers with a load, the best choice will be a model from 330 cm in length.
Model series Profi. reinforced protector It's a special tape of tight rubber that takes the brunt of the boat when it comes ashore, and it's a very low risk of puncture against sharp stones.
When choosing the length of the boat, consider not only the number of passengers, but also the dimensions of your trunk. Boats more than 360 cm in length when assembled may not fit in a standard station wagon without removing the rear seat.
Design features and materials used
The quality of any inflatable boat depends on the fabric. NGO Our Boats It uses reinforced polyvinyl chloride, which consists of two outer layers of PVC and an inner mesh of polyester filaments, which provides high tensile strength and abrasion resistance.
Seams in boats are performed by method hot-welding This creates a monolithic bond that is stronger than the material itself, and unlike adhesives, the weld does not dry out over time and is not afraid of temperature changes.
Paioles (floor) in boats can be made of moisture-resistant plywood or compositePlywood floorboards are cheaper and warmer to the touch, but require careful drying after each operation. Composite solutions are lighter and more durable, although they cost more.
☑️ Checking the boat before buying
The sling insert is the backbone of the stern of the boat, and it's made of layered plywood and protected. plastic-coated It's the transom that's the main traction load of the motor, so its integrity is critical.
Operation, maintenance and storage of vessels
The long life of your boat depends on proper care. After every fishing, especially in salt water or muddy rivers, the product must be rinsed with fresh water. PVC.
Drying the boat should be in the shade, in the straightened form. Direct sunlight can lead to local overheating and deformation of the material, especially if there are water droplets on the surface that work like lenses. It is better to store the product in a rolled up, but not overstretched, at a temperature of -20 to +40 degrees.
⚠️ Warning: Never leave a fully pumped boat in direct sun on a hot day. The air pressure inside the cylinders can exceed the permissible limits and cause the seams to rupture.
For minor repairs in the kit always goes kit However, for serious injuries, such as cuts greater than 5 cm, it is better to contact a specialized service, self-repair of large damage can disrupt the geometry of the balloon.
Proper drying and storage at room temperature is the guarantee that the boat will last you 10 years or more without losing its tightness.
Owner reviews and final recommendations
Analyzing user reviews, there are a few key points: owners appreciate the rigidity of the design and good swelling in models with a high level of weight. keelMany people say that boats NGO Our Boats They behave predictably even with lateral excitement.
The negatives sometimes include the weight of the kit when assembled, and powerful plywood-bottomed models with a motor can be really heavy to carry by one person, but they are a price for reliability and water-resistant properties.
When choosing a boat, clearly define your goals. For frequent trips for two with an overnight stay, it is better to take a model of the series. Solar. It's a light fishing boat, and a compact fishing boat is ideal. frigateIn any case, the products of this brand remain one of the best offers in the domestic market.
How to properly pump the NGO boat Our Boats?
Pump the cylinders sequentially, without immediately bringing to maximum pressure. First fill all compartments to 50-60%, then bring the pressure to normal (usually 0.2-0.25 atm). In hot weather, leave a small reserve, as the pressure will increase in the sun.
Is it possible to use a boat in winter?
Yes, PVC materials remain elastic at low temperatures, but in the cold, the fabric becomes more rigid, so assembly and disassembly must be done carefully, without sharp inflections, and you can't keep a frozen boat rolled up.
What warranty period does the manufacturer provide?
The standard warranty period for NPO Our Boats products is 12 months from the date of purchase, subject to compliance with the operating rules.
What is the difference between PVC fabric 750 g / sq.m. from 1100 g / sq.m.?
The figure indicates the density of the material. The fabric is 1100 g/sq.m. thicker, stronger and heavier. It resists puncture and abrasion better, but the boat will weigh more. For quiet fishing, 750-850 g/sq.m., for trophies and rocky rivers, you need a safety margin of 1100 g/sq.m.