Choosing a swimming aid for fishing or hunting is always about finding a compromise between load capacity, weight and cost. In the 330cm inflatable boat segment, one of the most popular solutions is the model. RiverBoats RB 330 This configuration attracts many water-engineers with its versatility, allowing the vessel to be used for both quiet walks and active trolling.
Unlike boats with sludge, technology is used here. NDMAIt's a very powerful way to change the way a boat behaves on the water, and you get a gentle ride, a great germination on the wave, and you can be comfortable kneeling while you're fishing for a trophy, but it has some features that you should know about before you buy, so you don't get disappointed.
In this article, we will discuss in detail the specifications, nuances of the assembly and the real driving qualities of this model. RiverBoats RB 330 Often choose to install engines with a capacity of up to 15 hp, and what pitfalls hides the operation of the inflatable floor.
Design features and materials
The basis of durability of any boat is the material from which it is made. RiverBoats RB 330 manufacturer uses a five-layer reinforced PVC This material is highly resistant to mechanical damage, ultraviolet radiation and aggressive environments such as gasoline or oil.
The key feature is the presence keelIt's not just shaped, it's also very stable at high speeds, and it doesn't add extra weight to the keel, as you would with a hard keel of plywood or aluminum.
All seams are made by hot gluing, which eliminates the risk of leakage even during prolonged use under load, and the cylinders are divided into several independent compartments, which guarantees buoyancy even in the event of damage to one of the sections. security It is the standard for modern inflatable vessels.
⚠️ Warning: Do not leave a fully pumped boat in direct sunlight for long periods of time unattended, and the air pressure inside the cylinders increases proportionally to the temperature, which can cause the seams to rupture.
The furniture used in RiverBoats RB 330It's made of strong plastic and stainless steel, and the mounts for oars, lintel rings and transom plates can withstand considerable loads, and it's important to note that the transom is made of 36 mm moisture-resistant plywood, which allows motors up to 15 hp to be installed without the risk of deformation.
Benefits of the inflatable floor of the NDND
The main feature of this model lies in the abbreviation NDMA (Low Pressure inflatable floor) Unlike hard sleigh, which has to be assembled from individual sheets and inserted into grooves, here the bottom is a single inflatable structure, which significantly reduces the time it takes to prepare the boat for launch.
Comfort is something that immediately catches the eye. NDMAYou don't feel the stiff ribs under your feet.
- 🎣 Freely move around the cockpit, changing position for throwing.
- ⛈️ It is easier to carry the swing, since the bottom cushions the shocks of the wave.
- 🏕️ Sleep in a boat on the floor without using inflatable mattresses.
- 🧱 Do not be afraid to drop heavy objects that can damage hard slate.
Another important aspect is thermal insulation, which creates an air gap between the water and the passenger, which helps to keep the heat warm in cold weather, and in heat, it helps to keep the heat from the hot side or the water.
The secret to fast-inflation of the NDLD
To speed up the pumping process of the bottom of the NDND, use a high-volume air compressor (CFM), not a high-pressure compressor. The pressure there is low, about 0.2-0.3 atmosphere, the main thing is to quickly pump a large volume of air.
However, it is worth remembering that rigidity The inflatable floor is still inferior to plywood sleigh when you go into planing under full load. If you plan to constantly carry 3-4 people and heavy loads, the acceleration dynamics may be slightly lower than those of sleigh models.
Technical specifications and configuration
To see if it's right for you. RiverBoats RB 330This model is a class of versatile boats that can be used alone or alone or together, and if necessary, threesomes.
Below is a table of basic parameters that will help you compare this model with competitors:
Parameter Meaning Total length 330 cm general width 145 cm Diameter of the cylinder 42 cm Load capacity 550 kg Boat weight (with bag) 48 kg In the standard completeness These are usually two inflatable seats (banks), a bag-pack, a remix, a product passport and oars (optional), usually aluminum oars, which add strength but also weight. For fishing, they are often replaced with lighter carbon-based counterparts.
The volume of the cockpit allows you to accommodate two fishing boxes, a sonar and other equipment without sacrificing legroom. cylinders (42 cm) provide good protection from splashes, which is especially important in choppy conditions on a pond.
Assembly and preparation for launching
Assembly process RiverBoats RB 330 It's very different from the classic models, and you don't have to mess with the sleigh sheets that can fit together or get stuck in the grooves, and it takes 10 to 15 minutes with the pump.
The procedure is as follows:
- 🌬️ Spread the boat and pump the keel-ballon to a pressure of 0.2 atm.
- ⚓ Pump side cylinders to 0.2 atm so that the boat takes shape.
- 🦵 Fully pump the inflatable floor (NDND) to 0.2-0.25 atm.
- 🔋 Bring the pressure in the main cylinders to the working (0.25 atm).
It's important to keep the keels in line. If you inflate the sides first, it can be difficult to access the bottom valve, and then you can use the keel to straighten the bottom properly, avoiding folds.
☑️ Checklist before first launch
Done: 0 / 5⚠️ Warning: Never use a car compressor without a built-in pressure gauge for the final pumping. Excess pressure in the heat can lead to strain of the seams, and failure to pump - to reduce driving performance.
After pumping, it is recommended that the boat be allowed to lie down for 10-15 minutes in the air so that the PVC material stretches and takes its final shape. normalize before launching.
Driving and handling
On the water. RiverBoats RB 330 It's a predictable, confident, inflatable keel, and it keeps the boat on course, even in the side wind, so it reduces the driver's burden and saves fuel, because you don't have to constantly adjust your trajectory.
With a 9.9 hp engine, the boat can easily plane with a single driver, with two passengers and a load, the plane speed will be about 25-30 km/h, enough to move along large reservoirs or rivers with moderate currents.
Tip: To improve driving performance and fuel economy, install a hydrofoil on the transom, which will help the boat to go faster on the plane and reduce yaw at high speeds.
Small boats are also high, soft bottoms can dampen the vibration from the engine, making the trip more comfortable, but you should consider that the sailing speed of inflatable boats is higher than that of metal or fiberglass counterparts, so in high winds you may need to anchor or use a dreck.
Wave resistance is a separate topic. RB 330 The soft side and bottom can take the impacts without passing them to the fisherman's spine, making it an excellent choice for morning fishing when the water is still calm.
Care, storage and winter conservation
To the boat RiverBoats RB 330 It's been in the water for years, and it needs to be taken care of properly, and PVC is a very unpretentious material, but it also requires attention, and after every trip, especially if it was a sea or a salt lake, the boat needs to be washed with fresh water.
Drying is a critical step, and even if the boat seems dry, there may be moisture between the layers of fabric or under the valves, which can cause mold and unpleasant odors, and you need to dry the boat in the shade, completely straightening all the elements.
- 🧼 Wash the boat with a soft sponge using soap solution.
- ☀️ Avoid drying in the direct sun in hot weather.
- 📦 Turn the boat down only after drying out completely.
- 🌡️ Keep the packed boat at temperatures between -20 and +40 degrees.
The best storage space is a spacious space where the boat is not crushed by heavy objects. Although modern materials are resistant to clamps, prolonged deformation at one point is undesirable. Periodically, once a season, it is recommended to topping up the boat and leave it in the straightened form for several hours to straighten the folds.
The main rule of long service PVC boat - complete drying before packaging and storage in a clean, dry place without access to rodents.
In winter, the boat can be stored in an unheated garage or on the balcony, and the main thing is to protect the package from direct sunlight and mechanical damage. RiverBoats RB 330 It will serve you faithfully for over 10 seasons.
Frequently Asked Questions (FAQ)
Can I install a 15 hp engine on the RB 330?
Yes, transom and cylinder design. RiverBoats RB 330 It allows you to install engines with a capacity of up to 15 hp However, it should be borne in mind that with such a motor, the boat will go on plane with only one or two passengers. When fully loaded (3 people + cargo), there may be no plane, and the boat will go in displacement mode.
Do I need to buy a separate pump for NDND?
A separate pump is optional, but highly desirable. Standard foot pumps ("frogs") have two modes: high volume/low pressure and low volume/high pressure. High volume is required for BNDT. Many modern two-stage pumps do this, but an electric pressure-adjusted pump will make the process much faster and more convenient.
How to repair punctures in the inflatable floor?
The NDNDM uses the same remix as the cylinders to repair the punctures, degreases the damage, patches the remix and rolls the roller, and lets the glue dry according to the instructions (usually 24 hours) before pumping, and if the puncture is in the seam area, you should contact a specialist service.
Is the boat enough for three people?
Formally load capacity 550 kg It allows you to accommodate three adults, but in terms of comfort, for three people, this boat is going to be a little cramped, especially if everyone has fishing gear, and the optimal load for a comfortable fishing trip is two people, and three people can be accommodated for a short walk or a short walk.