Fishing from the boat on ring It's considered one of the most extractive ways to capture large breams and ulcers in deep waters, and it requires careful preparation because the angler is directly above the fishing point, which imposes special design requirements for the gear. tooling allows you to effectively catch the bottom streams, where the stern cloud carries.
The main feature of the method is that the hooks with the nozzle must be strictly in the plume of the feeder, which uses a special metal ring that slides along the feeder cord, and an error in assembling a fishing rod or choosing the diameter of the fishing line can negate all efforts, especially when fishing on the current.
In this article, we will take a closer look at all the components of the system, from the selection of the ring itself to the nuances of the float load, and learn how to assemble a gear that will work even in high winds and changes in depth. The key factor of success is the ratio of the weight of the feeder and the length of the extended line of the rod.
Design and selection of the extension
The backbone of all gear is a fishing rod that needs to be compact but powerful enough to catch trophies. Usually, anglers use short rods that are 1 to 1.5 meters long. fishing-rod It's a hard-whip, so you can cut it down, and some craftsmen make the anglers themselves from the fiberglass tops of old telescopes.
The coil on this gear performs the function of storing the line and short-term catching. inertia Like the Nevskaya, or small meat grinders of 2000-3000, the main requirement is a smooth course and a reliable friction that will save the gear when a large fish is pulled, the fishing rod is fastened in the boat with the help of a special holder or fixed rigidly between the sides.
It is important that the angler has access rings in line with the coil, which minimizes the friction of the line when working with the cargo ring. If you use the telescopic option, make sure that the joints of the knees do not have sharp edges that can damage the fine mononity.
- 🎣 The optimal length of the rod is 100-120 cm for ease of work in the boat.
- 🎣 The fishing rod test must correspond to the weight of the feeder used and the current conditions.
- 🎣 The handle should be comfortable and not slide in a wet hand.
⚠️ Warning: Never tie a fishing rod to the side of a boat without the possibility of a quick discharge. When a large catfish bites or hooks, the gear can pull under the boat, flipping the boat.
Selection and installation of a sliding ring
The heart of this piece is itself ringIt can be made of lead, brass or steel, and the weight of the ring is adjusted so that the current does not carry it too high up the feeder cord, but also prevents it from falling to the bottom prematurely, and the standard weight varies from 30 to 70 grams depending on the strength of the flow.
Structurally, the ring has a hole for the feeder cord and a hole (or slot) for the fishing line. There are two main types: deaf and cut. The cutting ring It's more convenient to use because it allows you to quickly uncouple the feeder cord when you fish without pulling the whole gear out, but when it's strong, it can jump off spontaneously.
The ring is mounted on the feeder cord before being thrown, the fishing line is drawn into the ring's ear, and then the ring is put on the cord. When the gear is lowered, the ring carries the hooks with its weight, bringing them exactly to the feed source. The diameter of the cord hole should be 1-2 mm larger than the diameter of the cord itself.
When fishing on the current, the shape of the ring also matters. The drop-shaped shape creates less sailing and behaves more stable on the flow. If you use the purchase options, pay attention to the quality of the casting: the absence of metal inflows is critical for free slip.
Feed and cord: the basis of feeding
Without working properly. feeder It's not a ring fishing thing. It's a 3 to 10 litre container made of metal mesh, and the feeder's job is to keep the feeding for a long time, blurring it with the current, and create a stable feeding plume. The fine mesh clogs quickly, and the too big one pours out the feed in a volley.
The cord on which the feeder is lowered should be durable, smooth and not absorb water. Ideally suitable capron cord with a diameter of 1-1.5 mm or wicker line with a thickness of 0.4-0.6 mm. The use of cotton threads or ordinary string is unacceptable, as they soak, become heavier and strongly sail on the flow, violating the vertical gear.
The feeder is attached to the boat on a separate anchor rope or cord, which should always be in a tight state. If the boat is swinging with the wind, the feeder cord will go from side to side, leading the ring away from the fishing point. So often use two anchors: one fore, the other aft, or stretch marks to shore landmarks.
| Type of current | Volume of feeder (l) | Diameter of the mesh | Weight of cargo |
|---|---|---|---|
| Weak. | 3-4 | 5x5 mm | 2-3 kg |
| Average | 5-6 | 7x7 mm | 3-4 kg |
| Strong. | 8-10 | 10x10 mm | 5-6 kg |
| Very strong. | 10+ | 12x12 mm | 6+kg |
Lines, hooks and leashes
The main fishing line should be strong, but as thin as possible to provide minimal resistance to water. monophile The use of wicker is not recommended, since it is strongly sailing on the flow and it is visible to the fish, which can alert a cautious bream.
The lead is made of fluorocarbon or soft monofilament with a diameter of 0.14-0.2 mm. Leash length is a critical parameter. On a weak current, short leashes are put (30-50 cm), on a strong one - long (up to 1.5 meters) so that the hook with the nozzle has time to play in the flow. The number of leashes usually varies from one to three.
The hooks are chosen depending on the nozzle. For worm and worm, the long forearm models (No. 10-14 according to the international classification) are suitable, for mastro and peas - with a short forearm and a wide undergrazing. The color of the hook is preferable dark (grooved, bronze), so that it does not glare in the water.
- 🎣 Use a low-extensibility fishing line for better bite transfer.
- 🎣 Fluorocarbon leashes are less noticeable in water and are resistant to pike teeth.
- 🎣 The hooks should be sharp, check the sharpening before each fishing.
The main line and leash are better connected through the vertebra to avoid twisting the gear when exhausting. The vertebra also serves as a stopper, preventing the leash node from entering the ring hole.
Installation schemes for fittings
There are several options for assembling the tackle, but the most effective is the scheme with a draw leash above the ring. In this embodiment, the main line passes through the hole in the ring, and above it (at a distance of 30-50 cm) is tied or fastened with a carbine of a draw leash. tooling It allows the hook to be directly in the thick of the falling feed.
The second option is a blank mount, where the ring is rigidly fixed on the fishing line and the leash goes lower, which is less effective because the hook is often out of the stern, especially in lateral winds. The third option is the use of a skewer, which extends the leashes to the sides, preventing them from overlapping.
☑️ Checking the mounting of the gear
It's important to be consistent when you assemble, first you put a ring on the feeder cord, then you tie a fishing line to the ring, or you fasten it, and then you can put the gear in the water, and if you put the fishing line down first, the ring can get stuck on the bends or get tangled.
⚠️ Note: When using several leashes, make sure that the distance between the places of their attachment is greater than the sum of their lengths. Otherwise, when you exhaust, you will get a “beard”, which will have to be unraveled for a long and tedious time.
Catch and catch tactics
The fishing process begins with the boat being placed across the current or at a slight angle to it. The feeder is lowered vertically downstream at a distance of 3-5 meters from the bow of the boat. The feeder cord must be pulled. The hook ring is lowered.
The bream comes up to the feeder from the top upstream, so the hooks should be just above the feeder or level with it, but never lower. If the current is very strong, the feed plume can blow far away, and then it makes sense to let the ring down the cord, increasing the distance between the feeder and the hooks.
The snatching is done carefully, without any sudden jerks. A large bream at the depths behaves calmly, but at the surface it begins to rampage. suckerPulling fish out with your hands, especially if an ulcer or sazan is on the hook, is risky - you can hurt yourself or break a thin leash.
Once you catch a fish, you need to quickly check the nozzle and lower the gear again. Time plays against the angler: while you're fiddling with the fish, the feeder can empty or shift, and experienced anglers make this movement work and automatic.
What is the best course for catching a ring?
The optimal is the medium force flow, when the feeder does not blow much to the side, but the feed is washed out quickly enough to form a noticeable plume. On standing water, the method does not work, since there is no flow that carries the smell of the feed.
Can I catch a ring from an inflatable boat?
Yes, you can, but you need to be careful, the inflatable boat is tall, and it's not easy to work with long gear, and the sharp hooks and teeth of fish can damage the cylinders, and be sure to use a yawner and soft netting pad.
What to do if the ring is stuck on the cord of the feeder?
Don't pull too hard. Try to let go of the fishing line a little bit and play with the rod. If the ring is jammed because of the garbage in the feeder, you'll have to pull out the whole system. To avoid this, regularly check the contents of the feeder and the large factions.